Watch how ultrasonic cleans spark plugs

Ultrasonic Cleaner: s.click.aliexpress.com/e/_AFalG9
Detailed video: • Watch how ultrasonic c...
I was Pushing gas pedal but no acceleration and the engine misfiring, and i didnt had a check engine light so i can read any code, and i found out there was Oil in spark plug hole due to cleaning oil from engine valve cover gasket
so i had to change it and clean clean spark plugs
so Watch how ultrasonic cleans spark plugs

[@tymon995]

Those look like NGK V-Power Cooper plugs. They’re about $1.50 a plug, you might have spent more on the cleaning solution.. And cleaning them doesn’t regrow the electrode…

[@callishandy8133]

The short version of my answer ! You are absolute right ! Well done ! Perfect ! But if you like to controll the combustion ... have a closer look at the ceramic of the center electrode look for ceramic cracks and clean with tower and brass brush install the still udsble spark plugs Dont wait to long and buy new spark plugs. See how many torque the plug need. See rhe rust. That is no rust ! It is ceramic to outide sealing by NGK (and maybe rust). These spark plug have a gas leak and need to be replaced. See NGK webpage. AliMECH have to learn first car mechanic.

[@Tenkaichibudokai22]

Yes it does

[@calliris]

​@@Tenkaichibudokai22oh so whatever this magical ultrasonic fluid is can regrow steel?

[@samuel3253]

I thought exactly the same thing. No matter how much you clean it, a worn old car is still a worn old car.

[@Tenkaichibudokai22]

@@calliris yes.

[@barrycolla2506]

When i was working as an aircraftmechanic, we used to sandblast them in a machine from champion sparkplugs...those were expensive plugs so we always cleaned them and tested them...worked fine

[@johnnysolano1025]

You get out of here all this work for $5 plugs my guy

[@shaunconklin5694]

Even the most high end plugs are only 17 bucks a plug would still be a waste of time.

[@shaunlinde3439]

@@shaunconklin5694 would it actually be a waste tho? If you chuck it in and do other stuff and come back and just install it again...

[@shaunconklin5694]

@@shaunlinde3439 yes beacause it's going to be misfiring in a week or so and your going to be doing the same thing. Also the longer you run them the more likely they are to break apart that's more coming on turbo cars that are boosted. Any ways you change plugs like every 100k miles just put new ones in.

[@shaunlinde3439]

@@shaunconklin5694 ah yes that makes sense. Thanks

[@DavidJones-wq5fx]

eBay and Amazon are full of false spark plugs at $ 20 set of four . Real ones are about $ 20 each in Dealers. I prefer to clean and reuse my good known ones than getting fake plugs

[@muhammadafifazzindani9667]

Buy a new one you'll be fine, thank you

[@jonmyers8046]

Lol, I just did that with a bunch of plugs I had laying in my toolbox. Just curious. I tested them in my lawnmower to see which ones were ok and then put them aside for spares. I wouldn't use them for tuning up my car, but they're good for having around to diagnose small engine issues. When you don't have a lot of money, every penny counts.

[@Beloglazovalex]

Прикинь можно и поменять

[@a_n_toxa]

Воздушный фильтр забыл постирать

[@nikitagusarov2185]

@@a_n_toxa и масляный помыть

[@AndreyVor]

Тогда уж и масло через марлю профильтровать

[@homehandmade383]

​@@AndreyVor через самогонный аппарат 🤣🤣

[@callishandy8133]

тряпка Латунная щетка для свечей зажигания Больше ничего не нужно. Проверьте расстояние между электродами. Проверьте, не разбита ли керамика. Свеча зажигания течет, потому что на изоляторе видна ржавчина. Это может иметь и другие причины. Обычно свеча зажигания затягивается с слишком большим моментом. Это очень чувствительные свечи зажигания. Ну это двигатель. Видео мало чего стоит. Так не работает автомеханик, прошедший обучение. Так работают любители, желающие зарабатывать через KZbin.

[@Ni2205ck]

2 вопроса: зачем? Если свечи стоят не на много дороже комплекта фильтров Второй: масляный фильтр чем стираешь?

[@pfoxhound]

If the engine is fine - spark plugs are cleaned inside combustion chamber. 3$ regular spark plug? Is it worth it?

[@captainsupermaket8003]

We be cooking food for robots now

[@brake_4_cake]

Either the plugs are the problem, in which case they need to be replaced, or something else is fouling the plugs, in which case they'll clean themselves when you fix the problem. Neither is solved with an ultrasonic bath.

[@Sh-sh1hc]

Берете Димексид кидаете в баночку разогреваете и остается просто протереть, а если пшикать очистителем корб. То он еще сдует со всех щелей +они высохнут за 1 минуту. На свечах не останется ни капли грязи, они будут как с магазина

[@Centralflorida22]

What solution did you use?

[@jalimani-_-]

I want to ask please, what's the name of water compressor you used at the end of the video to clean. Thanks

[@BVP_edits]

Is it impossible to buy new candles?

[@JohnDoe-ef3wo]

I just hit the electrode with a wire wheel, and good as new 100% of the time!

[@callishandy8133]

No see NGK webpage or Denso webpage or learn car mechanic at a really good school.. But yes I clean sometimes well spark plug with a brass brush. Often it is better to use new spark plugs. You wrote as good as new ? Ok you have to learn a lot. The flash like sharb metal edges and there the electric field is extreeeem strong and the flash jump easy. Old spark plugs have rounded edges at the center electrode. Forget these spark plug an buy a new one. you have to learn a little bit mor of quality work in car mechanic. Even if you work in a car garage. The US guys are not well trained and spend years at a car mechanic school. I know it better, but still not perfect for raceing cars. But Porsche or BMW or Audi and spark plugs well premium high level education at top world level. Ok it was a long long time ago but I still look at the fingers from young car mechanics.

[@tinkerbell69714]

🤩WOW!! I KNEW THAT THAT THIS WAS POSSIBLE.JUST DIDNT KNOW HOW TO GO ABOUT IT. YOU ARE A GENIUS❤️💋 EXCELLENT JOB!

[@the_kombinator]

The brake cleaner near the end would have been step 1, then regapping the plugs step 2. Whatever the plugs took a bath in is completely unnecesary, a wire brush if anything at all.

[@callishandy8133]

No first towel for the dirt/oil than think why ther is rust ! Tust an sealing from inside say NGK You need new spark plugs. The sealing from inside to ouside is worse. (=Broken insdie ceramic or often to many torque?) Less rust or no rust ! You can clean it with towel, than brass brush. Ok break cleaner spray and twist the thread in a towel . But only of the center electrode have nearly still a sharp edge for the spark and the ceramic around have no cracks. Have a closer look at the colour of the combustion dirt. The only reason why I have often a look at my spark plugs. ok gap control and be careful if you regap ... Very careful ! Finsh with break cleaner spray Ready But always remember = new spark plugs are cheap and nice for the engine. A old 2nd hand scrap yard engine ... Remember = Torque must fit ! Not to many torque (and not to less). See NGK webpage Done good work Ultrasonic is not necessary. Yes, you can write overkill.

[@paulwolf8444]

A propane torch does much better. Just heat until glowing.

[@lone_wolfe]

can you ultraconic the spark itself or is it possible for blinker fluid to ultrasonic clean

[@massa6490]

Lacetti

[@xSBXGAMESx]

The ultrasonic cleaned my ears.

[@wdowa94]

My brain just melted xD

[@nunyabusiness896]

The primary reason to change plugs nowadays is erosion of the electrode, not simply being dirty. A set of 4 good plugs is like $40, you’d have to buy an ultrasonic cleaner and have a very low paid tech baby sit them to just barely come out ahead. Not worth it at all, just replace.

[@volvo09]

Yep. Plugs do not get dirty unless you are burning tons of oil, or running so rich that the exhaust reeks like fuel and makes you sick. Heck, now that I think of it, I supercharged my car 8 years ago and it has 100k miles on the platinum plugs I put in... Time to change them, not clean them.

[@clamax1974]

Buen procedimiento, pero no era mejor reemplazarlas? Aparte de toda la suciedad hay un desgaste.

[@DavidJones-wq5fx]

Mucha bujía falsificada en EBay y Amazon. Preferible limpiar las auténticas usadas mías hasta donde se pueda

[@clamax1974]

@@DavidJones-wq5fx nunca dije que hay que comprar en eBay o Amazon, obviamente ofrecen barato y lo barato cuesta caro. Hay casas de repuestos donde se pueden comprar, los fabricantes venden las mismas a un precio más bajo solo por el hecho de que no trae la caja con la marca del vehículo o el logo en la misma bujía.

[@adieywaniey6553]

What liquid u use??water or what?

[@rytin6580]

The problem is tip-in. Your throttle plate needs to be cleaned and you won't have the hesitation to tip-in with the pedal.

[@Lenzkrafters]

What fluid are you using to clean them in the ultra sonic cleaner?

[@AliMECH]

Seafoam, injector cleaner

[@TylerRivera635]

I paid 18 bucks for denso spark plugs….

[@ahmedmourad8284]

Buying new ones sometimes costs less than the electricity u spent and the liquid price and specially the time …

[@DatsunBloke7357]

A wire brush does the same thing.

[@johnnyreb1475]

Nothing better than fried spark plug for breakfast.

[@naingmoehtet8995]

What kind of liquid use?

[@shakeelrehman6572]

What is in the ultrasonic cleaner , water or what?

[@manjeshkumar2496]

I think putting a new spark plug is better ....when plugs head is cut inside the head is more cost to remove it

[@mihailynigin7988]

Что это за такой волшебный раствор?

[@Airknifemanufacturer]

hi dear friend, do you need air knife for ultrasonic cleans

[@ComputerGeek18]

All things aside, I'm curious if the ultrasonic vibrations are bad for the ceramic insulator.

[@callishandy8133]

Possible, but I dont think so. The guy AliMECH possible got a gerneral purpose 40 kHz ultrasonic cleaner. For mechanical prt to high frequency , but i will work and the buyer will be happy. He dont know it better and never will know it in his life. Around 60 kHz (or little higher) and you get softer cleaning and smaler imploding bubbles. Best for small parts than can break. But for electronic boards with electronic part mounted you will be safer to use above 60 kHz upto 80 kHz and under 100 kHz. But why ou clean a spark plug with ultrasonic ? First mechanical with a brass brusch. Than very short with a 400 sand paper the isolator (only get the dirt away but not perfect away ! One start and you work is ...) than use break cleaner to flush the brush dirt f out of the small gap at the center ceramic to the plug metal part. Gently use compress air . Ready ! You dont need to produce a like new spark plug ! On rev up with a cold engine ... i dont need to clean with ultrasonic. Towel, brass brush, break cleaner spray = Ready ! Have a close look at the center electrode. Nice sharp edge = well you can use it If the spark plug is older the gap will be worde 8you have to know how to adjust without get contakt to the chenter electrode and the ceramic ! One unvidible crack ... Really no good idea ! The center eletrode will be rounded by lost of center electrode metl FORM THE EDGE. Ask electronic enigneers or physic students for electrostatic field. Or use KZbin or google. Than you know that the electric field strength is very strong at a sharp edge. Tound edge is worde and you can start think to buy new spark plugs. These are not expensive ! You gasoline and your engine and you O2-sensor and your catalytic is expensiv. By the way if the spark plug fall at the floor, the ceramic WILL be BAD from the center electrode. A plug for the bin. IF your engine it a lot of dollar worth check new spark plugs after 200 miles if the ceramic is complete and not broken (parts will go from the combustion chamber (hope your cylinder wall is still ok) to the catalytic. Oh dear if Milligramm ceramic hit the turbo at 80000 RPM. Even a small one with nearly no weight. Often nothing will happen ! Sparkplug with floor contact is possible at your part dealer. And at your garage.

[@GR40RCapri]

@@callishandy8133I had purchased brand new plugs and installed. A week later- miss fire- The ceramic slid down the center electrode and was blocking arc to the side electrode 😳😳

[@videos-for-friends]

Just fork out the extra money and do it right, just did this last night throughout a valve stem seal job. had to spend $150 on plugs and wires… truck has never run smoother though.

[@KuntalGhosh]

150$? Oem plugs for my toyota is like 3$ each , had to spend 12$ to replace all the plugs every year 😂

[@NuwanLiyanage1983]

Thanks for the trick, but plugs are seen better days

[@ChefDuane]

You should still swap out your plugs periodically as the terminal erodes with use.

[@mr_s1na]

Nice

[@AliMECH]

Thanks

[@meandmyfish5353]

i need someone to do this to my brain

[@AliMECH]

Pray

[@YohTaiSai420]

Man... that's almost like how you make sausages in the morning.

[@CounterCultured]

Can’t be bothered to spend 10 bucks for new ones. I love it when my engine misfires 😂

[@kid5042]

Its not $10 it’s over 100 for some cars

[@johnle231]

What solution are you using

[@peter802311]

What about the electrodes wearing down on the spark plugs? I would just replace them.

[@jisuson8602]

Which fluid?

[@lesliechung79]

THOSE COPPER V NGK PLUGS ARE WORN OUT 😂

[@ojobreaker7743]

I mean yeah if you are already cleaning another part and have the setup and gasoline still in the ultrasonic cleaner then this would be fine but to set it up all for a set of plugs they would need to be some high end plugs to be worth the hassle. Or i guess if you have multiple sets that needs cleaning lying around

[@charlieb9502]

Why! if those plugs are $$$$ then yes. But from my point of view it just made them look pretty on the out side. That shit don't. matter. Now having a clean insulator inside and out is. Also having the proper spark gap. Also not having a breaks down of the internal electrode as well. I did period paint on a 14 cly GE Genbacher engine. Those plugs were $500.00 each. Yes I cleaned them and recapped them. And rand them for 1 week and put an inductive probe on the coil. And looked at the wave form. The last operator just replaced them and tossed them into 5 gallon bucket breaking the insulator. Each one of those plugs had a .5 gram block of pure platinum. I made bank recovering that.

[@MrTik-ex2oh]

Is that water, or other chemical substance?

[@Dresgarage96]

is that alcohol or thiner?

[@tylers7327]

No before and after on throttle ?

[@TheJacobbridges25]

Wouldn't it be best to just replace them? Do they lose some mass from the sparks? Or do they only get a black coating?

[@callishandy8133]

Replace is always the best way. These simple parts ... But the truth is that a guy have to know a lot of thinks ... Not only the gap distance and the colure of the ceramic around the center electrode. Remember = DO not use to many torque ! See the forst spark plug. That is no rust. It is sealing from inside. Often to mutch torque. Am I wrong ? See NGK webpage ans spend time ! Spark plugs can have inside a unvisible crack. This is the 2nd reason to see rust (=sealing and maybe rust). You and I are not able to find the reason. Spark plugs are cheaper than a 2nd used scrap yard engine. Yes in my youth I ignored the rust and cleaned it. Nothink happend. NGK or Bosch know what they write better than you. They dont need to sell some more spark plugs because you are careful. Again buy new spark plugs.

[@thearrow5793]

Not all the time working maybe you have a bad one..the best way to change them…

[@user-ge3hr3zq2e]

Я смотрю у этого чувака все поломки решаются с помощью ультразвуковой чистки.

[@deathchild2143]

Can you tell me where to buy tht at

[@impulseproductions1]

Great so now you have clean old plugs??

[@jurgenvau552]

Why not replace the plugs ... injector cleaning via ultra sonic okay, but plugs 🤦‍♂️

[@madunwerkstatt3093]

Interesting video, but I would replace those plug instead of cleaning it

[@HannaTBohman]

What fluid are you using?

[@AliMECH]

Seafoam

[@automotivegaragegautamauto5989]

Ya kon si mechanic ha sir g

[@andysierra6934]

Just because you cleaned off the spark plugs doesn't mean that the spark plug is worn out and needs replacing.

[@pfoxhound]

Ultrasonic bath is 👍!

[@TheAdatto]

Sandblasting with glass pearls ;))

[@a.j.williams195]

How much?

[@bricejeanne1842]

I know that there is a saying that says that there is no small savings, but from there to renovate spark plugs? You can find them in the shops for a pittance. And on top of that, they are wearing parts.

[@callishandy8133]

I look at the spark plug because I like to the the combustion result. Not for cleaning a spark plug. But if I compared all spark plugs, than I can clean it. Towel, brass brush, breakcleaner spray = ready Ok sometime I controll the gap distance. But TRUE = If there is no sharp edge at the center electrode, than I think if thise is the end-of-life-time for the spark plug. No ultrasonic is really needed. Ok have a cloder look at the ceramic around the center electrode. No cracks ! You see rust at the spark plug ? See video ! Often the plug installes with to many torque. There is a leak between outside ceramic ang plug metal. Or inside a crack. This is often no rust. It is the sealing. These plugs are worse and often worse because of the guy with the wrench and no torque in his fingers or a torque wrench. Sorry truth ! See spark plug webpages and learn. You can not find these information ? Worse page look for PDF from NGK. You will find these addition information. The spark plug face in the combustion chamber is not erverythink you have to know and control.

[@etiennepatrie7402]

What is the fluid on ultrasonic

[@harrychristenson4938]

What's in the solution?

[@krazed0451]

Wash them in a solvent, not just water. Ideally something that will help break down carbon deposits, those plugs aren't "clean" as long as there is schmutz all over the ceramic insulator.

[@FelipeLotas.]

Chapuza, en vez de comprarlas nuevas... Que va a ser lo siguiente? Reutilizar los neumáticos como hacen los de la india? Haciendo dibujo nuevo con una sierra circular...

[@Kowyn]

Ya no, I'll run new plugs.

[@Maksaccademy]

What liquid you pour in pot , it is water?

[@AliMECH]

It can be seafoam, Fuel-injector cleaner

[@Liam-ir6xm]

MAF sensor issue not plugs. My lancer does the same thing occasionally. I get out and give the MAF a couple of smacks with with my hand and good as gold

[@callishandy8133]

Worse contact indide or broken cable ? Buy a new MAF sensor (and not the cheap no name brand (=chinease cheapest production and sold by internet dealer, ever the biggest ...) Buy good brands (ok chinese can fake everythink and did it in my country). Mitsubishi Lancer and a smack ... No way Use google and search for Lancer owner club informations. Yes you haveto spend a lot of time , because you will read a lot of .... Beautiful !

[@amygrimshaw2787]

That pigeon in the background 😡

[@yosdasilva3093]

Air apa tu bang

[@travisuysaloglu9695]

Well if the gap is fine and there's no good ground then I'd do the same👍 no reason to buy new ones if the old ones just need a refresh

[@salimshamlan3347]

ايش نوع هذه الماده

[@AliMECH]

Seafoam

[@StanderGarage]

poderia ter passado na escova de aço antes....

[@cristianpadure7226]

How much age do you need to watch this

[@eduardochavezheredia6179]

Porque no cambias bujías nuevas. Creo sale más barato. Que hacer todo eso.

[@anotherrandomcommenter4473]

Italian tuneups would have prevented that entirely, lol

[@SizeableThoughts]

Theyre poked. Throw some new ones in there. Even if you get the tips clean the insulator is stained indicating leakage

[@lukasmisik2838]

Put a new ones there 🤦

[@Pickles523]

Those heat cycles def won’t cause it to strip over time

[@aarojunttila7447]

I have a solution called buying new spark plugs

[@DmitriyKomendantov]

Когда смотришь второй раз понимаешь что не помогло))) и то что вечно будет мыть... Пока не поменяет)))

[@islam8627]

А это ещё родные свечи этой машины, которые с завода ставят)

[@carlosd1296]

Yeah but how did the car perform afterwards? Ay yay ay

[@moeymouk-fi1jz]

I see I found another Terry

[@bad333p]

What liquid do you use?

[@AliMECH]

Seafom, or injector cleaner

[@verounbhim3631]

Hey can anyone explain exactly what this process is? Please? Thanks

[@AliMECH]

I did in this video kzbin.info/www/bejne/rXfZh2SBfLmMhdU

[@Youtube1isjdjdkdl]

Lasetti avtomat 1.6 mator

[@xxqick-_-shotsxx5587]

Clean spark plugs? Why didint i come up with this before?!.... NAAAATTTTT

[@mrdeadshot847]

People just get new spark plugs, it saves you lot of Time and money

[@dashonh1214]

The fact they still don’t look new

[@hildavieira9463]

All you need is a NEW set of spark plugs.

[@rpinterceptor1044]

lo que cuesta la solución para el ultrasonido cuesta un nuevo juego de bujías, esto sin contar que el ultrasonido no quita el desgaste ya ocasionado.

[@eiii5843]

Don’t do this you could weaken the ceramic and have the plug break while driving and cause a bigger headache.

[@f.e.producciones.6815]

Y si compras unas nuevas? No sería mejor?

[@rahim_bol]

that way is cheaper than buying new ones?