ALL Fit Iron Adapter

[@mikeyt4243]

Jim - good to see you explaining the system and boring out the hosel but the part we really need to see is you glueing the connectors to the hosel and the shafts.

[@robtrudeau7629]

Another great product review Jim. I’m about to start putting together a fitting system and will be checking out All Fit. Keep up the great work.

[@mikewilliams1479]

I see this being a fantastic set of tools for fitters. Have tons of preset shafts with the adapter and just change heads.

[@My-2-Cents]

Love your channel. Great learning resource. Used your tips to reshaft all my irons from steel to graphite. It’s been a couple years and zero failures. I’ll be interested to see if you notice any difference when you drill out a cast club-head.

[@docterroxo]

Great video. I'm curious if overtime there is any shaft rotation due to impacts. I also wonder if tightening it too much can cause cracks to graphite shafts or buckling to metal shafts and is there a possible "plug" to insert jnto the shafts for added strength to prevent that damage.

[@rickpetryk2658]

Another neat item thank you Mr Mcgolf

[@mattrevilock2038]

Cool content Jim. I hope all is well.

[@jacklabrador6981]

Well done Jim, thank you. So this system and the connex system require drilling out the hosel....thats too bad...I was hoping this system was easier without having to have a drill press....

[@allfitgolf]

a little drill is easy job, by that, you will see the great feature about the system comparing to connex.

[@jacklabrador6981]

@@allfitgolf No, not really when you dont have a drill press. Also, I dont believe the need to drill was mentioned on your website?

[@allfitgolf]

@@jacklabrador6981 sorry for not able to get website perfect, we are more products creator. We will try our best to improve our introduction. 🤝

[@xavierpousthomis1487]

Hi @McGolf, and thank you so much for your reviews ! I'd like to be sure that with this All-fit iron adapter the shaft will go all the way to the bottom of the hosel, just as it would be without this adapter. Could you please tell me if that is the case ? Thanks a lot !

[@docomo661]

Is it possible to enlarge the hosel using a handheld drill rather than a drill press?

[@gregcooke6637]

Hi Jim, have you tried the system on drivers that have no adapter?

[@gameallnightsleepallday]

Good video ! I’m guessing with a shim a guy could use taper tip shafts also ?

[@nerd9992]

amazing news. thanks!

[@bkirkwd52]

One issue. Hosel lengths are not all the same. Wouldn’t it be best to cut all hosels same length, drill out and then up weight of head were required with lead tape?

[@patrickzinuticzjr.3977]

Witht the All Fit connector, do yo in have to cut off a portion on the hosel? Each club is different.

[@katos84770]

at what speed do you have the drill press?

[@sbeasley1120]

I can't seem to find this on their site anywhere, are they doing a redesign or something?

[@anish772]

Does ALL-Fit still sell the adapter kits for Drivers/Fwy Woods?

[@kranjcarhongthong3861]

@mcgolf Allfit cannot bending for lie and loft angle right? Because i had been cracked for two iron head rightnow.

[@McGolf]

In order for the adapter to go in there is removal of hosel material making the hosel weaker in my opinion. That said while the adapter was installed I’ve bent a few with no issue. I imagine it’s up to the club

[@kranjcarhongthong3861]

@@McGolf thank you very for information.. i appreciate that

[@barracatcher6466]

So it’s a simple alignment and epoxy fit ?

[@richardlovelady7509]

Are you going to change all your club conex and won’t that be expensive.? On the club conex website they are a similar price.

[@h3inch1k27]

Thanks you !

[@KentnDebi]

Reamer is always a better cut Jim. You're best going with your engineering instincts 👍👍👍

[@jtwilliams1775]

Jim, What kind of shaft prep and length is required?

[@russellmagsanide]

Question: doesn’t drilling the hosel ruin the club’s head weight? If so, how does it affect the performance of the club versus a non-drilled club head?

[@Sir_Godz]

the adapter that goes in weighs the same as the removed metal

[@notagolfer9340]

Hoping to hit those Srixon heads on Saturday :)

[@davidrodgers6784]

Great info!!

[@Sir_Godz]

hey jim what system have you been using? I assumed it was connex.

[@elmwoodgc]

Just an FYI to everyone. Allfit is made in china.