Allett Kensington Tips & Tricks ☀️ (S2E20)

[@Striperman]

Thanks for the video Sunny great tips to maintain the mower. What I do for the blades and bedknife is I use a 200 grit sand paper for the blades and bedknife before each use. I then use the sandpaper for the cutting test because its thicker that the copy paper. When I am done mowing I hose it down. Use my blower to dry everything off and then spray the blades and bedknife with a silicone spray and then blow it again to even out the spray before I store the mower. After every few mows I use my Bedknife Buddy to keep it sharp. It has worked well to keep both sharp and rust free.

[@SunnyBermuda]

Amazing information! Thank you for watching and sharing! 👍

[@parikksit]

Solid tutorial, thanks mate!

[@SunnyBermuda]

Thank you!

[@derekcanada4426]

Great tips. Your Kensington is really clean!!

[@SunnyBermuda]

Thank you!! 👍😎

[@MrIsaacvillarreal]

Awesome video man.. Im enjoying my 1 week old Kensington 20h like there's no tomorrow. Thanks

[@SunnyBermuda]

Thank you!! They are great little machines! 👍

[@papamowslow196]

Great tips Sunny. I really like the idea of how you measure your HOC.

[@SunnyBermuda]

Thank you! Yes, with the flexing of the front roller that seemed the most logical way to measure it. 👍

[@BermudaBoss]

Great tips Sunny!! 👌

[@SunnyBermuda]

Thank you!! 👍

[@DIYDad1]

Dang dude this is a really comprehensive video. Well done! I need a mower like this in my life 😍

[@SunnyBermuda]

Thank you! This video could have easily been an hour long. 😎

[@GC987]

An excellent video. You're a credit to to Allett community. I'm in the UK and we have a Briggs & Stratton engine as standard.... so it's called a Kensington 20B - essentially the same machine (although the routing of the throttle cable is from the rear rather than the side of the machine (although Allett might be changing the routing on newer machines). The throttle lever has been redesigned by Allett in early 2021 presumably to address that ridiculously flimsy washer. A replacement is available from Allett/distributors. I too have experienced a tolerance issue with the scarifier cartridge and have found a longer bolt of the same size (but with a half inch longer length) improves that tolerance issue. well done for filming (with one hand a times) so very well. I shall subscribe and watch some of your other uploads. Many thanks.

[@SunnyBermuda]

Thank you for the kind comments! 👍 I appreciate your feedback on the 20B. I wonder if Allett would send a new throttle assembly that removes that flimsy washer from the picture.

[@GC987]

@@SunnyBermuda Mine failed completely and was less that 6 months old. I'm sure if you asked them nicely they would arrange something (maybe just sending you a more robust washer). I would think after one (or 2) seasons of straightening that washer, it's going to fail so maybe worth pre-empting the inevitable. Keep up the great work.

[@shaneallen4042]

Setting up my 17H in Queensland, thanks for the HOC chart and the vid greatly appreciated.

[@SunnyBermuda]

You bet!! Thanks for watching 👍

[@shaneallen4042]

@@SunnyBermuda how do you go with the height of the handles on the Allett? I'm 6"5 and am stooped over whilst using it.

[@SunnyBermuda]

I’m 6’2” but it catches me right at my waist so I’m able to walk up right, thankfully. I’ve seen some drill an extra hole in the bars to raise the height.

[@DaddingAllDay]

Awesome video! Really in-depth and enjoyable. Whenever I get ready to move on from my McLane Allet is on my radar.

[@SunnyBermuda]

Thank you! I think you’ll enjoy the Allett. 👍

[@YardEnvy]

All facts! I've had the same issues with mine! Great video Sunny 👍👍

[@SunnyBermuda]

Thank you! 👍

[@vk2him]

Very helpful video - the thickness gauge you were using is called a Feeler gauge

[@SunnyBermuda]

Thank you! 👍

[@MarkLester1982]

Great informative video as always.

[@SunnyBermuda]

☀️Thank you!! 👍

[@richardhall5126]

Thanks for mentioning that the scarifier cartridge is different than the other ones. I have only used the scarifier and I had the hardest time getting that bolt to catch. I was afraid all of the cartridges were going to be that way. Thanks!

[@SunnyBermuda]

Thank you! It surprised me, too. It was my first cartridge and it confused me, too. Thought I had a bad cartridge.

[@stephenwilliamson6118]

What a great video of top tips. I’ve got one ordered from Allett here in the UK. Great advise 👍🏻

[@SunnyBermuda]

Thank you! You’ll love your Allett! 👍 Thank you for watching!

[@YouCanDoItLawnCare]

Nice video! lots of good information there.

[@SunnyBermuda]

Thank you!! 👍

[@ReelLifeMowing]

Great video bud!

[@SunnyBermuda]

Thank you! 👍

[@johnhamilton9229]

I made it most of this one. I’m still a rotary guy. Trying to figure out what brand I will be committing to when that day happens. Thanks

[@SunnyBermuda]

If your yard isn’t too big check out the new Stirling line by Allett. All battery 🔋

[@johnhamilton9229]

@@SunnyBermuda do they permit a tryout period? Whom would I contact please

[@SunnyBermuda]

@@johnhamilton9229 They are headquartered in South Carolina. If you live close then you can try them out.

[@PrincessCutLawnCare]

sonny! can you email me that HOC chart please?? love that

[@SunnyBermuda]

Here you go: sunnybermuda.com/bermuda-grass-resources/

[@kgnok2020]

This is easily the most comprehensive video on this particular machine. Thank you so much for posting. This is my second season on same machine and for some reason it is cutting a tad lower on the left side. Is there any other adjustments I have missed to get a level cut?

[@SunnyBermuda]

Do you have Bermuda? This is a common problem I’ve seen from other Kensington owners. From what I noticed, my turf was so thick the machine floats on the turf and the way the drum spins lifts the right side causing the left to drop slightly. I’ve seen some add weights or a sock full of sand on top of the machine to counteract this. Oh, thank you for watching!! 😎

[@kgnok2020]

@@SunnyBermuda It is good to know it is not out of level and other Kensington owners are having the same problem. By the way I have zoysia lawn.

[@frankneidhardt]

I have the Atco Balmoral, which is the predecessor to your machine. Still runs like a dream :-)

[@SunnyBermuda]

That’s great to hear, hope to get many more years out of mine.

[@alanc7825]

Hey Sunny! Questions, how do you like the Allett Kensington 20” Honda? Do you recommend for a 4k sq ft. 1/2” cut bermuda yard? Do you think it is well built and will last? I have the Cal Trimmer now, and am really looking to move away from the rear wheels to the rear roller type. Also, I like the cartridges and the ability to have a verticutter without another machine. Dont have a large garage, etc. Thank You for all of your great content!

[@SunnyBermuda]

Alan, I like the Kensington 20H, but haven't used it much since getting the C24 and Buckingham. For a residential mower, it is an excellent mower that will transform your lawn especially if you get the turf rake cartridge. Ideally, I'd recommend the Stirling 51, but cost could be a factor. Come to Facebook and join the Allett Mower Owners group. A lot of people have had issues with scalping along one side as the Kensington (and Liberty) is a light machine and tends to float on thick turf. Then again, I see scalp lines on the big KZbinrs with their Toros, too. Hope this helps. DM me on IG for FB if you want more details.

[@rick5908]

The "metal paper" is a feeler gauge.

[@SunnyBermuda]

😎 Yes, sir 👍 Feels like metal paper to this old country boy 😂

[@carlosnieto949]

Another great video full of timely tips. I’ve been needing to do some of these on my Allett as well. But I have to ask, is that a Buckingham I see there in the background?

[@SunnyBermuda]

Thank you!! Yes, Buckingham 30H, to be exact. Hope to feature it in some upcoming videos.

[@Kevin_67_RS]

Sunny, another great video. Where are you getting parts and accessories. I need a few things for my Allett Kensington 20H (belts, etc)

[@SunnyBermuda]

Thank you! 👍Contact Allett USA directly on Instagram. That’s probably the easiest way.

[@scottmacdonald1381]

Thanks for the video! It was super helpful. Have you ever run into a situation where you hear a wobbling or uneven sound when you engage the reel?

[@SunnyBermuda]

Thank you!! Sent you a PM on IG.

[@salvadorzaldivar5040]

How are you liking your Allett mower? Where do you send your blades to get sharpen and serviced? I’m looking for your input before I spend over 3000$ on the Kensington H20.

[@SunnyBermuda]

Yes, it’s a considerable investment. I love the cartridge based system and quality of the machine. Only downside I’ve noticed is on thick Bermuda it will tend to float and scalp on the left side. Haven’t seen the issue with cool season turf. Use code SUNNY247 to get $100 off if you decide to buy.

[@salvadorzaldivar5040]

@@SunnyBermuda Would you recommend using it on Meyers Zoysia? Do you take the blades to a golf course or send them back to Allett to get sharpen?

[@SunnyBermuda]

Honestly, I’ve never mowed Zoysia and don’t much about it. Typically mail the cartridges to Allett US. If you’re near a bigger city you may be able to find someone to grind them.

[@traviswinston4629]

I really needed this video, thanks as always! Where do you order your Allett parts from?

[@SunnyBermuda]

Glad you enjoyed it! 👍 I contacted Roland Hall with Allett directly for parts.

[@webfeet1564]

Nice video! Do you know if there is a way to raise the HOC? Say closer to 2in.

[@SunnyBermuda]

Thank you! No, I believe 1.25” is the highest it will mow. It does come with a wheel kit to replace the front roller to aid in cutting taller grass.

[@jetskiergh]

Love the channel, but how many Alletts do you have haha good lord, was hoping you could help me, I have a new Buffalo I got from horizon and the unit is taking off on its own, wasn’t doing that a month ago, if I don’t have emergency brake on the. It will take off. I’ve loosened throttle cable at handle and under the motor side housing to its loosest point and it still takes off. Idle is not set high, don’t know what to do. Allett barely answers you anymore and this is a brand new mower. Maybe belts too tight? Replace belts? Can I use belt conditioner on these types of belts?

[@SunnyBermuda]

I have 3, want to sell the Buffalo? 😂 I’d take off the cover and watch it. The engagement mechanism may be stuck on. These machines from Horizon May be “new” but they all sat in a warehouse since 2018 so there may be rust or froze up pieces. I took my C24 and Buckingham apart down to frame almost and lubed it all. Yes, you can use belt conditioner on these belts.

[@jetskiergh]

@@SunnyBermuda thanks sunny, will try these tips, love the Buffalo but if you want to take it off my hands then shoot me an offer, will trade you for that buckingham set up 😊

[@jgonz8892]

Where do you send your reel for sharpening?

[@SunnyBermuda]

I currently mail them to the Allett rep in South Carolina - $150.

[@jgonz8892]

@@SunnyBermuda Thanks!