Gear swap follow up!! (Adjusting your limits)

  Рет қаралды 50,224

All-Pro Quality Garage Doors Inc.

All-Pro Quality Garage Doors Inc.

Күн бұрын

Пікірлер: 161
@migueletheridge4544
@migueletheridge4544 2 жыл бұрын
Saved me today,. I didn’t know how bad it would get out of alignment just by changing the chain gear and shaft. Thank you very much.
@ldinaustin
@ldinaustin 3 жыл бұрын
I'm adding to the list of thank yous. I spent a lot of time searching for information. So many videos on how to set travel limits when the limits are only a little off, and hardly anything on when the adjustments aren't functional. This was perfect! Exactly what I needed to fix the limits after I had replaced the coupler on my 18 yr old Craftsman. Thanks! Thanks! Bless all the youtubers like you who post this stuff.
@ALLProGarageDoors
@ALLProGarageDoors 3 жыл бұрын
Glad to help out Laura! I use youtube to fix things just like you, i'm just fortunate enough to pass what i know along. 👍🏽
@EZ-en3ub
@EZ-en3ub 8 жыл бұрын
Thanks for the clear video. Your video helped me find an idea to adjust my open/close limits to my gate. Here is the story: I had my Liftmaster 5580 ( from 2006) "fixed" by technician. The "fix" hold for 1 day... The Tech guy said that my gear was gone, and it will cost 350$ to replace it!, he also brought a new LM80 for 820$! I didn't agree of course. So, I looked for videos on KZbin and thanks for all the good people that filmed their fixing I was able to understand what is going on. First, I opened the motor back door and I looked carefully. My gear was as new! Then I followed this excellent video by +All-Pro Quality Garage Doors Inc. to have a start point. (2 minutes work time :) Now, my simple idea is to bring the the up and down limiters to their correct place by visual inspecting and manual rotating the screws. I disengage the gate and put a mark on the rail holder of the trolley once for the gate is closed position and another mark for open position to the height I want. Then I engage the motor to a learn position (2 clicks on the orange square button on the back of the motor, the the small light is blinking) The advantage at this mode is that every push on the remote controller is either moving up or down, so I can adjust the trolley position. So, I brought the trolley to the up position and then my simple contribution to the solution is to rotate the up limiter with a flat screwdriver until its metal contact is touching the metal in the middle wide limiter gear, while I am with the motor back cover open so I can see exactly the movements and where and how much I should rotate (no more guessing...) The same I did for the down position. Then I engage the trolly to the gate, start another learning mode and there it was fixed! (at list 2-3 times up and down with learning mode so this motor can adjust itself to the force required. (The blinking light is stooped when the engine did it learning job successfully). I hope this will help someone with the same annoying problem.
@joepolimine109
@joepolimine109 4 жыл бұрын
Absolutely an amazing quick fix to a frustrating problem. Many, many videos show how to change the drive gear and all of them fail to show your technique on how to adjust the limiters. They skip over that part of the repair and leave you wondering what it is you did wrong when the door won't stay down. Your video hits the nail on the head. BRAVO. Thank you very much!!!!
@ALLProGarageDoors
@ALLProGarageDoors 4 жыл бұрын
I agree! it is something often skipped over that leads you back to thinking you've screwed something up and often times ending up having to call someone to fix it when that's exactly what you were trying to avoid in the first place!!!! Glad you found the solution and got it taken care of. 👍🏽👍🏽
@vedvishesh
@vedvishesh 11 ай бұрын
Thank you so much for creating this video! Had the issue with my garage door and couple of reputed companies just declared the Garage motor dead. However, I decided to open the cover and found that travel module clip was loose. This video helped me fix the issue and now its working again... on the same motor !!! Thanks Again !
@ALLProGarageDoors
@ALLProGarageDoors 11 ай бұрын
Is there such a thing as a reputable garage door company? 😆 You did great… trust no one!
@rangerpru
@rangerpru 4 жыл бұрын
Thank You! Thank You! Thank You! After replacing the sprocket on my garage door, it was completely out of adjustment. The darn thing nearly ripped the track off the wall mount. I came very close to throwing in the towel until I found your video.
@markdecker6190
@markdecker6190 5 жыл бұрын
THESE GUYS ROCK!! If I lived anywhere near Santee, CA and I needed garage door repairs they'd be my FIRST call! Following their excellent videos I was able to swap my gear and sprocket assembly and then when I couldn't get the travel right I followed this video to the letter and after the recommended adjustments my 1994 era Liftmaster works like a champ. Thank you All-Pro!
@ALLProGarageDoors
@ALLProGarageDoors 5 жыл бұрын
Wow! That’s pretty good Mark! We appreciate you watching our vids and hope you get 20 more yrs out of your 1994 machine!! Thanks buddy! 👍🏻👍🏻
@deedub429
@deedub429 Жыл бұрын
Used this in 2023. Thank you for you help on this 21 year old garage door opener!
@jnellie1970
@jnellie1970 3 ай бұрын
This is exactly what I needed and couldn’t find anywhere else. Thank you! Subscribed and liked.
@genenegebretsadik4890
@genenegebretsadik4890 3 жыл бұрын
This is the best video, I watched a lot of video they never showed you all this detail. I really appreciated. It helps me a lot. I already gave up. But last minute when I saw this video I fix my garage. Wonderfull video. Thank you
@ALLProGarageDoors
@ALLProGarageDoors 3 жыл бұрын
That's fantastic Genene! Glad to hear you got it fixed! Thanks for watching 👍🏽
@stuartx7865
@stuartx7865 2 жыл бұрын
Great video! I've watched a bunch of videos and this is the only one that has tackled this topic. PS: I turned off the sound because the music is terrible.
@natertown
@natertown 8 жыл бұрын
You sir, just made my day!!! Just chalked that one off the honey-do list thanks to you! Thanks man. Where shall I send gift basket full of beer?!
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
Hahaha....how did you know that's my favorite gift??
@gchen10031
@gchen10031 6 жыл бұрын
After I changed sprocket when I tried to close the garage door it came back up after it hit the ground. I was clueless and going to pay $$$ to fix until I saw this video and decided to give a last try. This video saved me $, time and effort. Thanks a lot!
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Gang Chen glad to help buddy!!👍🏻👍🏻
@sfitz-rp4du
@sfitz-rp4du 5 жыл бұрын
Thanks a lot for this video and the one on replacing the drive gear sprocket. Very detailed and informative to complete the job!
@jgonzo220
@jgonzo220 7 жыл бұрын
Thank you for this video! I could not for the life of me figure out why the garage wasn't functioning after swapping out the gear & sprocket. Followed your steps and worked like a charm.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Jeffrey Gonzalez Thats fantastic!! The limits often get out of whack when doing a gear swap.
@steves2829
@steves2829 4 жыл бұрын
Nice follow up video to replacing the switch. Once you center everything up fine adjustments were easy. Thanks for the help.
@richardhill2195
@richardhill2195 5 ай бұрын
thank you! this is the info I needed to finish the job. I was just about to give up! I really appreciate the tip!
@ALLProGarageDoors
@ALLProGarageDoors 5 ай бұрын
@@richardhill2195 Never give up buddy! the answers are out there.
@BentRim
@BentRim 7 жыл бұрын
I just wanted to say thanks for making this video and your other one on the gear swap. I already had my drive gear out and was waiting on parts. Decided to do a little search and see what I could find when I came across the gear swap video. I hadn't even thought about the limit switches or locking my chain in place. Your video saved me some stress as I knew I had to figure out the end points before replacing the gear and chain. It was no big deal, but it could have been a mess. So you saved me a bunch of time and I now have a pretty good understanding how these units work. 7$ in parts vs 200$ for a new unit or much more for a garage door service to come out.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
That's awesome Scott!! Glad it worked out for you, it always helps when you gain a bit of knowledge along the way buddy!!
@robertberry6655
@robertberry6655 2 жыл бұрын
Thanks so much. You were 100% right. I replaced the gear and I had the timing out of whack. This worked for me very well.
@tungtop
@tungtop 2 ай бұрын
I have spent 3 days to adjust without knowledge untill I see this video, help me fix within 1hour, God bless you
@joeserao2496
@joeserao2496 6 жыл бұрын
Thank you so much. I was knocking my head against the wall trying to figure out what I possibly did wrong when I replaced the sprocket assembly. When I came across your video, it was just what I needed; something so simple but I would not have known based on any written directions.
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Joe Serao I hear ya Joe! It took me a few yrs before I realized i could make a video of this and attach it to the end of my gear and sprocket video and avoid having to answer the same question over and over, its very hard to explain it but when you can watch it on a video its so simple it makes you laugh!!!
@masonmontes
@masonmontes 6 жыл бұрын
You are a life saver, after much frustration and time spent trying to fix the problem this worked! Thank you so much!!
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Mason Montes Glad you tuned in and it worked out for you!! 👌🏻
@syngo13
@syngo13 5 жыл бұрын
Thank you for posting. My limit clips on the adjusters came off after replacing gears and bushings. This video helped correct the problem.
@fritz2259
@fritz2259 6 жыл бұрын
Thanks buddy I was having a hell of a time trying to adjust it kept running out of adjustment. and I found your video I would have never thought of removing the gear to adjust it worked great thank you so much for your video
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Fritz 2 no problem buddy!! Glad it worked out for you!
@DonaCamille
@DonaCamille 8 жыл бұрын
Thanks so much for your quick response, After following your suggestions I learned that my problem was in my RPM sensor on my LiftMaster 1300. When I replaced my worn sprocket I inadvertently mis-aligned/dislodged the RPM sensor pinwheel located on the end of the motor shaft, thus disrupting the infrared signal to my circuit board. Again, thanks for your invaluable information and I hope my experience will help another fellow DIY'er in our quest to save a buck!
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
Excellent!! Glad you were persistent enough to track down the problem and it's now up and running!
@DanielSchuessler-sf3pv
@DanielSchuessler-sf3pv Жыл бұрын
Thank you very much for posting this video. Great video. Helped fix the issue I was having.
@lalonfakir7919
@lalonfakir7919 7 жыл бұрын
The ONLY video that helped me nail down the problem of my Sears Craftman door opener and solve it. I'm a layman and don't get too many opportunities to congratulate myself😀Thanks Mike for the video.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Lalon Fakir excellent!!! Glad to see you got it solved! Thanks for watching.
@robertcabrera1046
@robertcabrera1046 3 жыл бұрын
Thanks for the video. I adjusted mine and now it's working. You saved me hundred dollars, cheers!
@ALLProGarageDoors
@ALLProGarageDoors 3 жыл бұрын
Fantastic!! 🍻
@kathymurrayhealthyliving3176
@kathymurrayhealthyliving3176 5 жыл бұрын
Thank you so much for this AWESOME video. I'm not very handy and need instruction like this. I switched out the sprocket gear but the door was haywire and the adjustment screws were not working. Just by looking at the still frame at about 1:30 in... I could tell that my yellow wired sensor had fallen off the white "up" screw. I got it back on and then followed your instructions to the letter with the hand adjustments. It wasn't anytime at all that I had the door functioning perfectly. THANKS AGAIN!!! You not only saved me money but also helped give me a great sense of accomplishment.
@ALLProGarageDoors
@ALLProGarageDoors 5 жыл бұрын
That’s fantastic news Kathy! I know how you feel, I use youtube all the time to research products and figure out how to fix things I’m not familiar with and it works, I get things fixed! Glad now to have an opportunity to pass it forward!! 👍🏻👍🏻
@timothyhanstine1243
@timothyhanstine1243 6 жыл бұрын
GREAT VIDEO! I found myself needing to accomplish this after I replaced a broken belt. In following the video I also discovered what was probably the root cause of the belt breakage. In this case it was the retainer clip holding the odd shaped gear in place was missing. (not sure we it went) Since I saw that it was actually a low stress situation so I simply used a tiny zip tie. All in all, I'm a happy dude that saved money, and the door now shuts softly, and on the up limit side doesn't hit the stop. Did I say Great Video, and of course a huge THANKS!
@yanksfan8989
@yanksfan8989 6 жыл бұрын
Thanks for the insight on the limit switch. Made adjustments with cover off U pointed me in the right direction Great video
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Robert Caiazzo 👍🏻
@jamesrichardson559
@jamesrichardson559 4 жыл бұрын
Thank You!!! My drive sprocket broke and I replaced it just fine. The problem was the up an down adjustment limits were out of range.Your video saved me a lot of time trying to figure it out.
@ALLProGarageDoors
@ALLProGarageDoors 4 жыл бұрын
It happens all the time!! Glad to help out JR! 👍🏽
@bowser0798
@bowser0798 8 жыл бұрын
Thank you so much for this video. I needed to understand how this assembly worked because I screwed it all up. You saved me a lot of time, money and for that I can't thank you enough.
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
+bowser0798 ....You just did Bowser!!! Glad to help out!
@diymotorcycling1719
@diymotorcycling1719 2 жыл бұрын
I commend you sir!!!! I don't know what I would have done without finding this video!!!!
@ALLProGarageDoors
@ALLProGarageDoors 2 жыл бұрын
Glad to help out!! 👍🏽
@jackwhite8014
@jackwhite8014 2 жыл бұрын
I want to thank you for coaching me thru this repair. Following your instructions definitely helped. But I would like to suggest you add narrative to this video, it’s very hard to read and then follow your steps by reading at the same time. Thanks for the video.
@ALLProGarageDoors
@ALLProGarageDoors 2 жыл бұрын
Great Idea Jack! when i get some free time i’ll see if i can do that.
@joepowell2619
@joepowell2619 9 жыл бұрын
Thanks Mike for making this video! I had to help someone with this exact issue last week after there gear swap. Now if they are having trouble with the instructions I have given them, I can link this video to them!
@ALLProGarageDoors
@ALLProGarageDoors 9 жыл бұрын
I had the same problem Joe, a lot of folks who do a gear swap get their limits messed up and explaining this method over the phone or in comments and emails was just way too hard...it needs to be seen.
@honkeytonkjohnnygumbo1137
@honkeytonkjohnnygumbo1137 7 жыл бұрын
Greeeeat video! After replacing the gear, i thought i was done when door wasnt working properly! Your video is exactly what i needed! Saved the day bro!
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
NoJustass NoPiece booya brother! Glad to be able to help out, its a simple adjustment but people overlook it often.
@honkeytonkjohnnygumbo1137
@honkeytonkjohnnygumbo1137 7 жыл бұрын
All-Pro Quality Garage Doors Inc. Boooyah right back atcha! Hey so i greased up the plastic gear and worm gear with the entire grease packet, and made sure to get it. in the teeth, but after running it it seems like theres not that much grease in there. How heavy is it supposed to be greased up (not that i have any left) and are u supposed to grease the shaft of the gear and sprocket? (Because i didnt and would dread taking ut apart again)
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
NoJustass NoPiece no your good just using most if not all the packet, when you first run it it will spit alot of it out but thats ok, maybe recheck it in 5-7 yrs and make sure the chains not too tight and your good to go!
@kitcheves1132
@kitcheves1132 2 жыл бұрын
Excellent video! My limit sensor was actually in pieces when I took the opener apart, but everything snapped back together and I was able to adjust it using your instructions.
@ALLProGarageDoors
@ALLProGarageDoors 2 жыл бұрын
Excellent!!! Glad to hear it! 👍🏽
@jftman53
@jftman53 Ай бұрын
Great answer to my known worry. My gear was stripped so bad the motor ran but the trolly stayed still. The motor would stop going one way but keep running the other. It makes sense to center everything. I am wondering how these plastic rods do what they do?
@terrycrissman7392
@terrycrissman7392 3 жыл бұрын
My up travel limit had run out of travel and this showed me how to reset the up/down switch travel limits...thanks!
@ta2fr3ak
@ta2fr3ak 2 жыл бұрын
Many thank yous sir..,been fighting that sob for about 4 hours...
@ALLProGarageDoors
@ALLProGarageDoors 2 жыл бұрын
I feel your pain brother!!
@mtbristol
@mtbristol 4 жыл бұрын
Great job, exactly the fix my LiftMaster needed, thanks a ton!
@Alex-uz6bk
@Alex-uz6bk 4 жыл бұрын
Another grateful watcher. Great video. Many Thanks.
@ALLProGarageDoors
@ALLProGarageDoors 4 жыл бұрын
Thanks Alex!! Hope the vid helped!
@rodrobinson6111
@rodrobinson6111 2 жыл бұрын
How do I get the trolley in the center of the rail? Do I pull down on the red cord and then hit the garage button on the wall? Also, once the adjustment are made, will this help with my issue of the garage door hitting the stop bolt and when closing the door comes back up? Any help is much appreciated. Your videos are very helpful.
@ALLProGarageDoors
@ALLProGarageDoors 2 жыл бұрын
yes to all questions. when your testing it leave the cover off so you can see whats going on inside.
@rodrobinson6111
@rodrobinson6111 2 жыл бұрын
@@ALLProGarageDoors I appreciate your response and videos. Everything is working again. Again thanks for your response. Keep those videos coming, they are very helpful!!!
@ALLProGarageDoors
@ALLProGarageDoors 2 жыл бұрын
@@rodrobinson6111 Thank Rod… appreciate it.
@anthonykayson4952
@anthonykayson4952 7 жыл бұрын
Awesome subtitle ( after I screwed them up) was EXACTLY where I was. Thanks. My 27 year old opener working like new
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
anthony kayson excellent!! Simple fix and up and running!
@AbuHashim399
@AbuHashim399 Жыл бұрын
Thanks for this clear video, that helped me so much
@garypyzanowski3889
@garypyzanowski3889 Жыл бұрын
Thank you so much for this video. Worked for me.
@bwilson1649
@bwilson1649 7 жыл бұрын
Searched but missed this until after I fixed a problem. I found my "Straight Door Arm" bent and the trolley at the wall end of the T rail. After disconnecting the door, the trolley would only travel about a foot then shut off. After looking at several other possibilities including the speed sensor that others suggested, I looked inside the housing and noticed the traveling limit switch contact was near one end of the drive screw. I adjusted the drive screw to put the moving limit switch in the middle just like this video shows. Then I adjusted the down and up limit switches about an inch from the drive screw and operated the trolley (without the door attached) to determine if I had the limits approximately correct. At this point, I could have adjusted the travel limit screws if I needed to, but I was close enough to correct that I decided to attach the door and run the opener again. A couple of adjustments of the down and up limit screws and both the open and closed positions were good. The cause of my initial problem was probably that the down limit did not make contact and the motor kept running, causing the nylon drive screws to flex and its gear disengage. I may need to replace the limit switch drive assembly if the drive screw loses its position again. I also need to reduce the down force because the straight arm was bent when the opener malfunctioned.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
B Wilson yea, always do the testing on a light force control, ck the limit contacts, make sure they are clean maybe hit em up with some real fine sand paper.
@SpikesMavic
@SpikesMavic 6 жыл бұрын
Great vid thanks , would not of been able to do that tuning without your vid . thanks again
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Glad it worked out for you Stanley!!
@NodesofTravel
@NodesofTravel 3 жыл бұрын
What can I say ... this video was just the thing I was looking for... the down travel is perfectly fine. However the up travel still doesn’t come back up all the way . But whatever so far is miles better than what it was at ...
@paulkeenan4309
@paulkeenan4309 2 жыл бұрын
So, I am installing a 1979 vintage GDO that has the chain and trolley completely disassembled from the t-rail and also the travel limits were randomly set all over the palace and most likely do not correspond to any position of the motor. However, BEFORE I attempt to "fine tune" the travel limits per your video, I need to "synch" the chain trolley position to correspond to the motor's fully closed position and for that I need to keep the limit switch from interfering (I think ...) with the chain/trolley travel. Do I need to have the DOWN limit contacts (brown wire) set to a position far enough away from the center contact (gray wire) so that the chain can engage the inner trolley BEFORE the limit switch DOWN contact shorts to the CENTER contact? Or does it NOT matter where the down contact is set? Or, should I DISCONNECT and REMOVE the travel limit switch all together during the initial motor-chain synch? If I do the latter, with the limit switch removed, will the motor keep trying to move the chain even farther after the trolley engages? TIA for any reply.
@ALLProGarageDoors
@ALLProGarageDoors 2 жыл бұрын
i wouldn’t disconnect the limits, if the limit is close to the down then bring the inner trolley close to the down position then engage the door and fine tune it.
@michaelmeyer3326
@michaelmeyer3326 3 жыл бұрын
Thanks so much !! I did a gear swap and the limit switch was maxed out after I tried to adjust it. I took it apart again and thought I broke it. I snapped it back in , followed your video and it works like new !! Thanks again !!
@ALLProGarageDoors
@ALLProGarageDoors 3 жыл бұрын
Glad to be of assistance!! 👍🏽
@snake4945
@snake4945 10 ай бұрын
Hi - so I removed my chain and unsure what cycle the opener was in , will this work for installing the chain also?
@ALLProGarageDoors
@ALLProGarageDoors 10 ай бұрын
yes it will, put the trolley somewhere near the middle and match it with the gears and you’ll be real close then just fine.
@RGTHESHOP
@RGTHESHOP 5 жыл бұрын
Thank you. Saved me $120 +
@stevemalone4972
@stevemalone4972 9 жыл бұрын
Mike, the top of my chain gear sheared off and the chain got all twisted up. I replaced the gear assemble using your video. It was very helpful. I had to wrestle the chain back on and readjust it. Now when it runs there is a clicking sound from the gear at the top of the unit. I noticed the chain on the right side of the rail as you face the garage door is slight torqued. I think that is what is causing the clicking sound. How can I fix it? Thanks for your help.
@ALLProGarageDoors
@ALLProGarageDoors 9 жыл бұрын
Steve Malone Hi Steve...back before the invention of the chain spreader I would get a clicking sound on a lot of machines, sometimes it's because the chain was too tight, other times...too loose, and sometimes there was no way to get rid of it, you just hoped that after a few months it would go away. The noise is caused by the chain not feeding on the sprocket perfectly. Try "slightly" loosening the chain and see if it gets quieter or louder, if it gets worse then go the other way and tighten it some more, one way or the other usually makes an improvement. Try to get it as quiet as possible then let it go for a few months and see if the sprocket wearing in lets it quiet itself on its own, if not then try the same adjustments again.
@Chris_g221
@Chris_g221 7 жыл бұрын
I fucking love KZbin. I had this issue after my chain fell off, I replaced the chain and trolley assembly, followed this video and BOOOOOOOOOOOM!! Thanks mate
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Gotta love KZbin!!!
@mikemilam525
@mikemilam525 5 жыл бұрын
Thank you very much. Replaced the gears and everything was off.
@motocruiser5966
@motocruiser5966 8 жыл бұрын
Hello and thank you for the great video. I got my 1991 Craftsman 1/3 HP opener to work after putting the new gear on it but it stops about 4 to 5 inches from the garage floor and immediatley goes back up without stopping. With the cover off I notice that the down limit does not make contact with the other metal piece, it stops about 1/4 inch before hitting the contact and then reverses its travel as the garage door goes up. In order to keep the garage door from going back up I had to adjust the limiter so it touches the contact right at the point of where the door goes back up in order to keep the door closed (so there is about a 5 inch gap between the floor and the bottom of the garage door). Any ideas on what is causing this to happen and what I can do to fix it?
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
Has to be either I-beams or force control, turn up the down force a number or two.
@motocruiser5966
@motocruiser5966 8 жыл бұрын
The beams are okay and the force control is turned all the way up. Is it possible that when the spring broke (that is when all of my grief with the opener started) it did some damage to the opener's motor? I replaced both springs and checked the tension on both of them. The door closes completely to the floor when I close it manually; the tracks are clear and they operate smoothly. For the life of me I can't figure out why I cannot get my opener working properly.
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
It's probably something simple, check the plastic notched wheel at the end of the motor shaft and make sure that it's pushed all the way on to the shaft, one guy in the comments said his wheel was loose or off, if its off your machine won't travel more than 6 inches if it's too far back on the shaft it could cause the problem you are having. operate the door down then let it reverse and come back up then count the number of flashes the LED light on the back of your machine gives you...it's giving you a code as to whats wrong. it will be a sequence of flashes from 1 to 6. but push the slotted opto wheel all the way snugly on to the shaft first and make sure the small circuit brd that reads the opto wheel is on snug as well.
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
Very...very doubtful that your door springs are causing this. One more thing you can try that might sound kind of strange but spray the back side of the wood jambs and or wood trim (on the outside... that your door travels down) with silicone or WD-40 if you see any burn marks your door has left on the back side of the wood from rubbing...do this first before ANYTHING else.
@MrDodgerfan88
@MrDodgerfan88 9 жыл бұрын
Mike... my sprocket snapped when the door was closed and my trolley is close to the opening of the door. I replaced the gear/sprocket.....In adjusting my limits how do I move the trolley to the Center? When I go to open the door the trolley travels about a foot into the garage and then stops and travels back towards the opening of the garage. I am guessing that I need to remove my repaired sprocket/gears an then manually move the chain and trolley to the middle prior to adjusting the limits. Any help would be greatly appreciated. Thanks
@ALLProGarageDoors
@ALLProGarageDoors 9 жыл бұрын
+Dodger Fan Yes...loosen the chain, remove it from the sprocket and manually rotate the chain until you are in the center of the rail then do the same with the limit assy gear and fine tune from there.
@MrDodgerfan88
@MrDodgerfan88 9 жыл бұрын
+All-Pro Quality Garage Doors Inc. Mike...finished the Gear replacement and adjusted the limits. I have to thank you for providing great info and enabling me to do the repair. Saved me some $$, total cost of fix was $28...haha. I am so stoked!!! Thanks again....
@ALLProGarageDoors
@ALLProGarageDoors 9 жыл бұрын
Excellent! Job well done Dodger fan!!
@jimwillis8914
@jimwillis8914 6 жыл бұрын
Great video on re-setting limits after changing out gear sprockets. I set the close (1/2 HP Craftsman) perfectly; however the open repeatedly hits the stop screw and when I watched the limit tabs with the cover off it made contact well ahead of where it stopped, meaning when the tabs made contact during opening, it never stopped. I checked and the wiring was intact from the limit tab to the circuit board. Any ideas? Do I need a new board?
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Jim Willis I had one the other day doing just that... i sanded the contacts and put a drop of wd-40 on it and it worked fine. Not sure for how long.... but worth a shot.
@DonaCamille
@DonaCamille 8 жыл бұрын
I'm at my wits end. I repaired and replaced my sprocket, adjusted and reset the limits per your video, which is outstanding, and believe me I've checked out a few before finding yours. However, when I run the LiftMaster it only tracks approximately 12-15 inches down and then returns to the center position. I have not attached the door to the rail train because I am afraid of damaging my door. Any suggestions?
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
I would check your force control settings and make sure they are not set too light and make sure your chain is not too tight.
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
depending on the year of the machine, when it comes back up to a stop it should flash you a code from the LED light on the back of the machine telling you whats wrong depending on the number of flashes.
@rmgrip88
@rmgrip88 6 жыл бұрын
My new gear drive seems to be working properly but the motor will only move in the up direction until it hits the stop screw. Is this a limit problem or did something go wrong when I installed the new gear drive? Why wont it go in the opposite direction back down. Bad wiring?
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
rmgrip88 did you reconnect your safety eyes? If you hear a clicking sound ten times after the opener is activated to go down then its safety beams. Make sure the opto-wheel is tight on the end of the motor shaft and that the rpm sensor brd is on tight.
@rmgrip88
@rmgrip88 6 жыл бұрын
@@ALLProGarageDoors thanks! That was it... one of the wires came loose during the install
@markhallman2088
@markhallman2088 7 жыл бұрын
I replaced the gear and sprocket in a 1/3 HP Craftsman. After replacing, the door will only travel a foot or so and then return to where it started. In looking at the limiter screws and the center screw, the door doesn't travel to either of the limiters. Any thoughts would be appreciated.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Mark Hallman you might have forgotten to put the opto-wheel back on the motor shaft.
@markhallman2088
@markhallman2088 7 жыл бұрын
Thanks for that. I pulled the wheel off and put it back on and unplugged and plugged the RPM sensor back in and all is well. I hadn't connected one of those correctly. Thanks so much for responding and for making the videos.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Mark Hallman no problem buddy, glad you got it sorted out!
@yijinliu
@yijinliu 7 жыл бұрын
Thanks for the video! Where can I buy these gears? The gears in my 1/3 HP are worn out. I need to replace them. I couldn't find these parts from homedepot or amazon.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Chao Liu you could call our shop and ask for Paul, he might be able to ship them to you
@xlegaciex
@xlegaciex Жыл бұрын
Just to be clear, the arm should be disconnected from the trolley first or can it be left on?
@ALLProGarageDoors
@ALLProGarageDoors Жыл бұрын
disconnect until ready to fine tune it… or just keep the force control settings real light.
@fredcoder3161
@fredcoder3161 5 жыл бұрын
I did a gear swap and did your adjustment but when the contacts come together nothing happens, the door keeps going until it hits the stops. I even unhooked the yellow wire and connected it to the grey wire and still it didn't stop. I clearly have another problem. Do you have any idea what it could be?
@ALLProGarageDoors
@ALLProGarageDoors 4 жыл бұрын
follow each wire into the wiring harness, make sure they are tight in the harness and the harness is snugged down.
@lifeisfree868
@lifeisfree868 6 жыл бұрын
Thank you, thank you, thank you! This was exactly what I needed.
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
LifeIs Free glad to help out! 👍🏻
@kevinwells4888
@kevinwells4888 2 жыл бұрын
Thanks buddy you saved my bacon.
@peternewman3847
@peternewman3847 6 жыл бұрын
Great Video! The gears were all out of whack on my Liftmaster opener after the plastic sprocket coupler broke. It would be cool if you could link this video to that problem. Once again, nice job - thanks for posting!
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Peter Newman Thanks Pete! I’ve got it linked to the very end of the gear & sprocket video where I hope folks can find it. Glad it worked out for you!
@rapaent
@rapaent 3 жыл бұрын
THANK YOU!! Great find due to being in a bind. Exactly what I've been trying to find. P.S. The thumbs down on this video are cluless. Thanks again! 👍😊
@ALLProGarageDoors
@ALLProGarageDoors 3 жыл бұрын
Thanks Rapa! glad the video helped you out! 👍🏽
@rapaent
@rapaent 3 жыл бұрын
@@ALLProGarageDoors I followed your tutorial which had me up and running within 15 minutes! Without your video, I would have been at a total loss! THANK YOU!! 👍😊
@Jas4u2
@Jas4u2 8 жыл бұрын
Great video , no bullshit to drive people up the wall , well done .
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
Thanks James!
@yanksism
@yanksism 6 жыл бұрын
At what point do you hook the garage door back into the trolley?
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
as soon as you've made your limit adjustment and backed off the force control dials, then reconnect and test.
@yanksism
@yanksism 6 жыл бұрын
All-Pro Quality Garage Doors Inc. Thanks, I installed everything this morning and figured it out. Door is working fine. Thanks again for the video
@ALLProGarageDoors
@ALLProGarageDoors 6 жыл бұрын
Sweet! glad to hear it Frank!!
@UtahTroutHunter
@UtahTroutHunter 7 жыл бұрын
So I followed your instructions. However my issue is my trolley will only move 1 foot forward 1 foot backward. So I moved it to the middle of the rail and it will only go like 1 foot and then returns one foot. I have the limits suggested just like you showed in the video. Any ideas? I did replace my gear and that's when I had this issue arrive. Thanks for any help!
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Check to make sure the black notched opto wheel is pressed all the way on the motor shaft.
@UtahTroutHunter
@UtahTroutHunter 7 жыл бұрын
All-Pro Quality Garage Doors Inc. Freaking genius dude! That is exactly what it was. I took it off and was turning to the shaft with a pair of vise grips to get the trolley where I wanted it. Bingo! Thank you so much man!
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Josh Bell can i get a fricken BOOYA or what!!
@UtahTroutHunter
@UtahTroutHunter 7 жыл бұрын
All-Pro Quality Garage Doors Inc. BOOOOOOOOYA! Thx man.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Josh Bell you got it buddy... we git it done!
@joebilhete1162
@joebilhete1162 7 жыл бұрын
just a great video, well done
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Joe Bilhete ....... Thanks Joe! Hope it helped.
@joebilhete1162
@joebilhete1162 7 жыл бұрын
your a life saver, just brilliantly done without all the long BS speeches Thanks again.
@rooh5825
@rooh5825 5 жыл бұрын
Good video, but it would be nice if you showed a little bit more about adjusting the pressure once you get the up and down limits set.
@jameschorman8034
@jameschorman8034 7 жыл бұрын
Thank you, this really helped me out.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
James Chorman... excellent! Thanks for watching.
@doppelgangertx1
@doppelgangertx1 7 жыл бұрын
this fixed my problem perfectly!
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Bingo!!
@salvoembers3263
@salvoembers3263 7 жыл бұрын
awesome video... saved me some cash on a new opener.
@ALLProGarageDoors
@ALLProGarageDoors 7 жыл бұрын
Salvo Embers Heck yea buddy!! Save that cash!!!
@Jas4u2
@Jas4u2 8 жыл бұрын
So much bull out there , your video is perfect , thank you for sharing .
@ALLProGarageDoors
@ALLProGarageDoors 8 жыл бұрын
No problem James, Thanks for watching buddy!!
@lspr215
@lspr215 4 жыл бұрын
THANK YOU!!!
@Jas4u2
@Jas4u2 8 жыл бұрын
New assembly installed no problem .
@gonepriused
@gonepriused 8 жыл бұрын
Thanks, Great informative video~!
@miguelmartinezhdz5717
@miguelmartinezhdz5717 3 жыл бұрын
very good 👍
Сестра обхитрила!
00:17
Victoria Portfolio
Рет қаралды 958 М.
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
小丑女COCO的审判。#天使 #小丑 #超人不会飞
00:53
超人不会飞
Рет қаралды 16 МЛН
How to change the gears or sprockets in a garage door opener
6:18
What wears out a garage door opener? - Compaan Door & Operator Co
2:14
Compaan Door and Operator Co.
Рет қаралды 38
DON'T MAKE THESE MISTAKES - Garage Door Gear Sprocket Replacement
12:57
SOS Garage Door Service
Рет қаралды 128 М.
Chamberlain/Liftmaster 971LM (battery swap)
2:13
All-Pro Quality Garage Doors Inc.
Рет қаралды 25 М.
How To Lubricate Your Noisy Garage Door (Goodbye, SQUEAKS!)
9:37
AmplifyDIY
Рет қаралды 2,6 МЛН
Replacing the Drive and Worm Gears on a Chain-Drive Garage Door Opener
7:00
The Amazing Benefits of Tilt-Up Garage Doors
2:16
Door and Dock Solutions
Рет қаралды 474
Garage Door Not Opening?? Broken Gear Replacement
22:15
HouseImprovements
Рет қаралды 368 М.
Painting   other. Garage Door
4:09
Acj Houston Garage Doors
Рет қаралды 940
Сестра обхитрила!
00:17
Victoria Portfolio
Рет қаралды 958 М.