Limit Switch Operation inside a Liftmaster 2280R Garage Door Opener

  Рет қаралды 22,298

Tim Beavers

Tim Beavers

Күн бұрын

Пікірлер: 33
@Mugwart1
@Mugwart1 Жыл бұрын
This is one of the only videos that goes into solid detail about the limit switches and how they operate. Many thanks for posting such an informative video!
@toadywindinthewillows2721
@toadywindinthewillows2721 7 ай бұрын
Brilliant video Tim, this is the best video description of the internal workings of the garage door range limiter. Handy people now have a great guide for a very DIY fix.
@chadleechadder5961
@chadleechadder5961 11 ай бұрын
Very helpful. The revised part at the end was a big help!
@Stranger_1
@Stranger_1 2 жыл бұрын
I'm glad I found this video, after my center coupler broke and was replaced my unit would only turn a couple revolutions and then stop, the diagnostic light was blinking 5 lights telling me I had a problem with the rpm sensor, but I couldn't find anything wrong with it so looking for answers online a lot people were suggesting the logic board. After watching this video however I found out that when my coupler broke the center part of my limit switch had somehow jumped its contact. All I had to do was take it out, re-seat it and fine tune the adjustments and we are back in business. So thanks a lot for this video!
@tomtom5981
@tomtom5981 3 жыл бұрын
Your video gave me insights into a problem that had plagued me for about 24 hours. Am very grateful, fellow human!
@beavesf16
@beavesf16 3 жыл бұрын
Thanks! glad it helped!
@sabraunstein
@sabraunstein 2 жыл бұрын
Me too Tom Tom. Couldn’t sleep all night. Mine was that screw in the middle that doesn’t adjust with the upper and lower up/ down screws.
@lovesloudcars
@lovesloudcars 8 күн бұрын
Well presented and explained including the end remarks. No wasted time or explanation here, good stuff. I have a different type, but suspected what you described. My problem is the door got jammed and somehow broke the plastic thing that travels between the upper & lower contacts!
@heroknaderi
@heroknaderi 3 жыл бұрын
Thanks for showing how this Mecanism works. I enjoyed watching.
@jasonwarwick633
@jasonwarwick633 3 жыл бұрын
Same as others commenting - Thanks you helped me fix my issue with the stops. Mine was the same as yours, it is old and the stops had migrated over many adjustments o where there was no travel left.
@beavesf16
@beavesf16 2 жыл бұрын
Thanks! I cringe when I watch it - not the best production value - lol. But if the video helps folks, and it apparently has, then mission accomplished!
@stephenstiles7517
@stephenstiles7517 3 жыл бұрын
This was a great help. I replaced the gear drive and the switch.
@martinsholomskas1363
@martinsholomskas1363 2 жыл бұрын
Thanks, for posting this video. I replaced the gears and shaft that drive the belt, but could not get the opener to function correctly. It seemed to me that something was wrong with the limit switches. After viewing this video I was able to see what was wrong with the limit switches and correct their position. BTW I was doing this when it was in the 20's outside. Thanks again.
@beavesf16
@beavesf16 2 жыл бұрын
Thanks! Glad it helped you! My gears probably need to be replaced soon too - good to know that it's possible. And extra points to you for working with cold hands.
@navonparag2516
@navonparag2516 7 ай бұрын
Thank you so much for this video , you made me understand what is the problem with my Liftmaster . 🙏
@jttylor6516
@jttylor6516 2 жыл бұрын
Thank you for a clear demo. It cleared up a mystery and helped me set my limits!
@donhorn548
@donhorn548 2 жыл бұрын
Your video was very helpful, especially your follow up starting at 4:00. Thank you
@timfischer
@timfischer 3 жыл бұрын
Another (easier) way to center the limit switch is to simply disconnect it from the motor by removing the bottom nut on the main spindle (one clip removes it). Then move the limits out of the way, and manually turn the center screw to get the wiper where you want it. Then you can reconnect it and set the limits properly.
@beavesf16
@beavesf16 2 жыл бұрын
Thanks for your additional input. It's always helpful to know that there are other options available.
@sabraunstein
@sabraunstein 2 жыл бұрын
Exactly. Kept me up all night!
@davidhill3606
@davidhill3606 4 ай бұрын
Thanks for the video!
@tobychellin2323
@tobychellin2323 2 жыл бұрын
this video helped me! thats for the knowledge!!
@euclon
@euclon Жыл бұрын
Also, those copper contact surfaces can become oxidized or dirty resulting in inconsistent limit travel of the door, especially noticeable when closing. IOW, sometimes the door will do a relatively hard close. Clean the surfaces with contact cleaner on a swab.
@freebird8485
@freebird8485 8 ай бұрын
Thank you. Helped me so much.
@dkkssshekel7600
@dkkssshekel7600 11 ай бұрын
I have a question, should these upper and lower limits be about a quarter way in on either side to optimally allow for adjustments both ways?
@lakewalker
@lakewalker 3 жыл бұрын
My limiters are making contact, but the motor does not stop. All wires look connected and in good shape. Do you think the logic board is to blame?
@binmerai1439
@binmerai1439 3 жыл бұрын
Useful, thanks
@msgtammo8929
@msgtammo8929 2 жыл бұрын
How do I reverse the motor. I was adjusting the limits and not it seems the motor is stuck trying to go down but it just clicks and hums. Is there a trick to getting the motor to move the opposite direction
@beavesf16
@beavesf16 2 жыл бұрын
Do you have the case off so you can see if the sliding switch is making contact with one of the limiters? Sounds like a limiter is not aligned and/or not making contact with the sliding switch (when it does, it stops the motor and reverses polarity for the next open/close button press). The clicking sound is not good. You will eventually wear down nylon motor gears - each click is a gear "jumping" the worm gear (I think).
@VIDEOPNEU
@VIDEOPNEU 2 жыл бұрын
You saved my life... The wife was going to kill me.😂
@jamesanonymous2343
@jamesanonymous2343 3 жыл бұрын
CLUMSY VIDEO,,,,,CAMERA ON THE HEAD IMAGING,,,,DONT BOTHER YOUSELF WITH THIS ONE, BUY A MANUAL !
@aby2269
@aby2269 3 жыл бұрын
he didnt even have to make this video, he did it clearly not for money but good intention, so shut up and leave
@yeltube
@yeltube 3 жыл бұрын
Really appreciate this video. One of the little sensors had broken off in mine, but I didn’t even know how to get inside to know this. This video showed me how the limit sensors worked AND how to get inside. Thanks very much!
Garage Door Not Opening?? Broken Gear Replacement
22:15
HouseImprovements
Рет қаралды 368 М.
Quando eu quero Sushi (sem desperdiçar) 🍣
00:26
Los Wagners
Рет қаралды 15 МЛН
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 56 МЛН
Garage Door Limit Switch Replacement - Craftsman 1/2 HP
6:21
Craftsman lift master problem rpm sensor solve
5:26
The Friedgizzard Channel
Рет қаралды 41 М.
How to Balance Your Garage Door
7:25
DDM Garage Doors, Inc.
Рет қаралды 856 М.
Garage Door Keypad Not Working? How To Fix Easy
8:42
Todd's Garage
Рет қаралды 481 М.
Bypass Garage Door Sensor using 555 timer
15:01
Joel SomeIdeas
Рет қаралды 109 М.
Garage Door Opener Circuit Board Replacement
8:33
Dollar
Рет қаралды 40 М.
Bypass garage door safety sensor.wmv
11:58
Joel SomeIdeas
Рет қаралды 754 М.