Alpharex LED Tail Lights Install and Review

Before spending money on the Alpharex LED tail lights, take a look at this quick install and review video. It may change your mind if you are on the fence about them. P/N 630010 Alpharex PRO-Series LED Tail lights for 14-18 GMC Sierra 1500, 2500HD, and SRW 3500HD are super easy to install. Note that these do not fit trucks with factory LED tail lights. Website states that these will not fit SLT or Denali models, well thats not correct. Nacho is a Denali trim 1500 Sierra but does not have LED tail lights from the factory so these work just fine.

[@Mason-to9fv]

hi buddy questions i ordered the 2014-18 alpha rex luxx edition but seems the wire doesn’t plug to the panel of the car it’s different

[@danielmeraz1628]

They look good! Are you going to do more mods on your sierra?

[@jazzlejohnson5364]

Thanks Daniel. Absolutely! I hope to go bigger on the lift, motor/trans upgrades, boost, and interior refresh.

[@danielmeraz1628]

@@jazzlejohnson5364 hopefully you put your upgrades on KZbin so we can see it and get ideas for our sierra. Keep the good work coming. Liked the morimotto headlights you installed and i just ordered the tail lights after watching your video.

[@jazzlejohnson5364]

For sure! Hopefully you don’t have to wait as long as I did for your tail lights to show up.

[@Builttolastdenali]

Also it says on their site they are compatible with the 14-18 Denali models. Have you had any issues ?

[@jazzlejohnson5364]

Zero issues besides the piss poor fitment of the factory plugs into the housings. Even with that, I am not disappointed so far.

[@Builttolastdenali]

@@jazzlejohnson5364 I mean they still fit though right? I’m thinking about getting them..but i don’t feel like going through another headache like I did with their nova series head lights..had a hyper flash for days

[@jazzlejohnson5364]

@The Safe Haven, they fit perfectly. These taillights should not hyperflash, have resistors already built into them. Was no joke plug and play after you swap over the mounting tabs from the factory units. Just make sure the harness running down inside the cavity is pushed over a bit to clear the back side of the housing and it will sit perfectly flush. If a section doesn’t work, unplug it and flip the way it was plugged in. LEDs are polarity sensitive.

[@Builttolastdenali]

@@jazzlejohnson5364 cool thanks brother, I’ll most likely be ordering them soon 👍🏽

[@bradyhannon3081]

You are my only hope lol, I installed these. Didn’t drive for a week. Didn’t start, jumped my truck got it going, next day couldn’t start. Are they draining my battery or?

[@jazzlejohnson5364]

I wouldn’t think they would be draining the battery. You sure your battery didn’t keel over? Mine bit the dirt one day with no warning. Started fine in the morning then dead after work. Your taillights aren’t getting power with the key off.

[@bradyhannon3081]

@@jazzlejohnson5364 yeah man I’m thinking it just gave up on me right at the time I install these. Lol. Will let you know installing new battery soon

[@bradyhannon3081]

Just ordered for 2016 Sierra. Will I need a harness. If so where can I find one?

[@jazzlejohnson5364]

Shouldn’t need a harness, should just be plug and play.

[@mklein345]

Just called Alpharex. Said they are only compatible with dually gmc's.Is your truck a dually?

[@jazzlejohnson5364]

Is not a dually. Regular ole run of the mill 1500 Denali. Work like a champ on mine.

[@chuckkolancz4969]

the 620010 are for silverado 1500-3500 Incandescent and sierra 3500 dually. The 630010 is for sierra's only and will not work on silverado's according to their website

[@22andymvp]

Howdy man. If you still have original lights... I'd like to buy em.

[@americansoldier7776]

For a minute there I thought you were the Yankee Marshall lol. If you don’t know who that is just search for him on KZbin. He is a popular gun channel

[@jazzlejohnson5364]

Must have been my accent. I get that a lot…nope, no I don’t. I’ll have to go look up that channel.

[@LyttonKing]

They did not work the way I thought it was gonna work, thought the led part would go with the turn singles and not those lame blinking thing, and it did not have a sequence or anything, it looks sick, just the lights functions did not exceed my expectations

[@AZTechLabs]

who cares if you messed up.. it usually takes multiple takes and editiing. just get to the point.

[@jazzlejohnson5364]

Learning as I go. Thank you for taking time to comment, any feedback is appreciated.