Alpine window fitting on steroids!

[@joseoti1441]

Your video gave me the courage to reinstall my alpine windows after a local shop botched the job. Repeatedly chanting ‘patience’, got them all in. Set no time records but your instructions were easy to follow for a first-timer. Did the second alpine in under 15 min. Thank you!

[@BritannicaRestorations]

Great job!

[@davelozinger1780]

Mike! I just installed my windows using your method and it worked like a champ! Just under ten minutes!

[@BritannicaRestorations]

Whoa! You will be doing all the local Land Rovers now! Well done! Mike

[@KevsSanders]

The best YT 4x4 stuff by far

[@BritannicaRestorations]

Thank you! Mike

[@AbelDoodeman]

Mike, i really love it how you really, really hate that "Worse & Daft - 40" stuff..............

[@BritannicaRestorations]

It's good for fitting glass!

[@Viaticboston]

Watched this 6 months ago, kept rewatching trying to pluck up the courage. Lockdown means I’m going to do this job tomorrow( definitely taking the roof rack off 1st) fingers, toes and everything crossed.

[@BritannicaRestorations]

WD40 is your friend!

[@Viaticboston]

Job done. Cheers Mike.I didn’t have anyone to help me lift the roof rack off so wedged a load of fence panels under it. Lifted it enough to get all the way round the seal. I used a right angle pick to fit the new seal, not ideal but did the job fine. Unfortunately the filler had perished too much on one side so as a bodge( which worked very well surprisingly) I cut a section out of the old seal which had a very similar profile to the filler. Plenty of WD40, 3 brews and 4 hours later all was in and solid. Cheers again.

[@matthewburgess5034]

Just the tutorial I was looking for. Can you please tell us what 'implement/tool' you're using?

[@BritannicaRestorations]

www.morrisminorspares.com/body-inc-panels-trim-c21/screen-rubbers-glass-c32/fitting-tool-for-chrome-plastic-windscreen-insert-gls111-trm1002-1006-rubber-insert-details-p828587

[@mattvandart9055]

What tools were you using other than your concentration tongue?

[@BritannicaRestorations]

WD40, and a windscreen install tool Similar to this www.frost.co.uk/windscreen-rubber-seal-installation-tool.html

[@matthewhunt3323]

@@BritannicaRestorations thank you

[@philippecompigne2152]

Hi mike I m french ... nobody is perfect :-) I have 2 défenders (200 tdi 110, 300 tdi 90) and a série 2a I have changed thé Windows of the 110 one yesterday with the mike wd40 method Only 30mn a window... fantastic Thank si lot

[@BritannicaRestorations]

Nice 👍

[@AlbertBraae]

Do you know if the glass is interchangeable between series 3 and 90, or if it needs to be year specific? Thanks

[@BritannicaRestorations]

Yes they are almost the same - only difference was glass thickness - could be 4mm or 5mm. I don't know why, but only the 5mm seal is available now

[@gnarlyboot477]

Hi, just spent a full day (less a few coffee breaks) fitting one Alpine window to my mate’s Series 3 station wagon, which also has a safari roof. Like your experience with the roof rack this was awkward. But the real problem was the size of the window to the roof aperture. The glass seemed really small and wouldn’t stay in the seal groove while fitting the retainer. Even though no new parts other than the seal and retainer were involved. In the end we prevented the lower edge of glass from sitting in the seal groove by placing a ruler between them. This fully engaged the upper glass edge into the seal while we fitted the retainer. Once we were had 50% of the retainer fitted we removed the ruler and were able to fit the rest of the retainer. Using this method, with lots of WD40, it took about 30 minutes. with the retainer in place the window sizing seems good and secure, the seal seems to spread significantly with the retainer in place. We found the special tool with roller just popped the glass out, and just used an old screwdriver to bush the retainer into place. Glad it’s finished. Thanks for all the good advice, and great video content.

[@BritannicaRestorations]

It's not easy and the ones I did were factory cut, but the glass was still tight Well done - least you didn't cut the seal like I did on one or two Mike

[@chrislendenbarnes7503]

I use good old Fairy (up liquid). Dishwashing detergent. Use it more on my cars than in the kitchen.

[@BritannicaRestorations]

Glass fitter doing a friends 110 screen in in New York - full day trying to install it - no joy Rang me to ask what was going wrong - use WD40 I said! Next day had the screen in within 20 minutes !

[@LandyVlad_Rides]

Are there alpine windows a suitable size to retrofit to a 130 Double cab ute?

[@BritannicaRestorations]

I don't think so

[@paulfowler2790]

Excellent Mike. Is there any limit to your skills with Land rovers?

[@BritannicaRestorations]

getting paid....

[@John-nw7cu]

@@BritannicaRestorations 🤣🤣

[@davidwoods80]

8 minutes, plus 30 years of experience, Mike. I'd have both broken the glass and gouged the paint down to the metal in several places.

[@BritannicaRestorations]

lol! WD40 is all you need - and the tools!

[@dietmarw]

@@BritannicaRestorations Would silicone spray also work or are there some drawbacks with using that?

[@BritannicaRestorations]

Sometimes silicone on paint is difficult to get off - especially if you are re painting

[@PyleHD]

Doing this on my series 2a, orderes from britpart it said to fit series but it seems like the selal is not thick enough, when i fit it first i csnt just nudge the window inside since it just falls through, the window is too small to get to the lip on the other side. Any ideas? Is the seal wrong or am I doing something wrong?

[@BritannicaRestorations]

The glass has had the same dimensions since the Series 1, however there is 5 mm glass and 4mm glass - I think you can only get seal for 5 mm now - maybe the hole is not cut right?

[@PyleHD]

@@BritannicaRestorations Thanks for the reply. The hole is original as far as I know and I'm not sure for glass thickness. Spent whole day today and managed to fit it but there is gapfrom seal to aluminum. Kinda annoying that after buying new seal and busting my fingers for serveral hours I still need to resort to silicone sealant to prevent leaking afterwards...

[@werxdesign]

So I followed your video today to put in the alpine windows, and after I got it seated in the surround seal, it wasn't stable and kept wanting to pop out. Did I not cut down the outer seal enough so it's being pushed out? I'm always concerned of cutting the seal too short and leaving a gap. Any advice as after an hour of trying to get it in, I got super frustrated! Thank you!

[@BritannicaRestorations]

From your description, you may have the seal the goes in the roof too long, and it is fighting against itself

[@werxdesign]

@@BritannicaRestorations I'm always afraid I'll cut it too short, ha! Thanks Mike

[@romrokth]

Man that was great to watch Mike!

[@ocmadrilltech3625]

Hi Mike, do you have the cutting template in order to cut the right size to fit the glass?

[@BritannicaRestorations]

No but Masai4x4 sell one www.masai4x4.com/Paper-Template-To-cut-out-apertures-for-Alpine-Windows-p62569284

[@ocmadrilltech3625]

@@BritannicaRestorations Thanks!

[@stephenjohnson3520]

What tools are you using to pull the rubbers over the window?

[@stephenjohnson3520]

Just found it www.amazon.co.uk/gp/product/B01ENQPQQY/ref=ox_sc_act_title_1?smid=A16XFW0MUWQIF7&psc=1

[@BritannicaRestorations]

That's the one - very rare thought they had stopped making them

[@gagatube]

Nice work.🙂 Bonus points for the 😋 'Professional concentration' subtitle! 😂

[@jamesanderson84]

Impressive combination of great technique and brute force. Well done that man!

[@BritannicaRestorations]

Glad you liked it!

[@Viaticboston]

Nailed it. Tidy job

[@コベチチベコ]

It was helpful★★★★★.　I was able to install the series 2 alpine window today.

[@BritannicaRestorations]

Glad it helped!

[@dariuszrad2661]

I am asking for the glass number of the window pane

[@BritannicaRestorations]

4 mm or 5mm? Plain or tinted?

[@dariuszrad2661]

@@BritannicaRestorations 4mm tinted

[@BritannicaRestorations]

MWC4714

[@dariuszrad2661]

@@BritannicaRestorations dziękuję

[@samjone1]

Any problems with damage to the window seal rubber using WD-40? I have read that this can be a issue combining WD-40 and rubber/plastic.

[@BritannicaRestorations]

No, the oil evaporates pretty quick - never had a problem

[@bmc1569]

Thats a world record!!!

[@BritannicaRestorations]

I did both sides in less than 15 mins

[@marco_au_boulot6747]

Really impressive. Can you put a link where purchase the same kinf of tool than you use :) thx

[@BritannicaRestorations]

www.sheridanmarine.com/product/window-rubber-tool The V shape one I made myself using an old screwdriver and a bit of stiff wire

[@Viaticboston]

I’ve just used a right angled pick which worked perfectly well. Just be careful not to poke a hole through the seal.

[@nbell4166]

Mike I have old style roof 1985 is there any way of cutting the roof side's and installing this types of windows? Will roof loose on strength or is it worth of trouble?

[@BritannicaRestorations]

No it will be fineHere is the template www.masai4x4.com/Paper-Template-To-cut-out-apertures-for-Alpine-Windows-p62569284

[@nbell4166]

Great thank you Mike. On eBay new seals and second hand windows could be around £80-90. Happy to invest in that. It will be nice addition once it's resprayed in summer. Nick

[@BritannicaRestorations]

Just remember to get it into the right position - you may want to fit a headliner later and there is not that much room to manoeuvrer see here kzbin.info/www/bejne/jV67dH-botp7mrM Mike

[@nbell4166]

Thanks that link is great help, it's explain it all 👍

[@thegrimreaper7777]

It's like the game in 'The Generation Game' on TV where the professional does it first, then the contestants try to do it afterwards....Bruce Forsyth lives Again..

[@BritannicaRestorations]

Good game, good game!

[@Mike-yq6jg]

any tips on cutting these windows into a roof

[@BritannicaRestorations]

If you got the template from Masai, marking out will be easy, but cutting is tricky as you only have one shot. A grinder with a thin slitting disk is good and by taking small chunks out you can do the rounded ends - but cut the hole smaller as you can file or grind it out, but you cannot put metal back on For me I have a metal template I run round with the plasma - but I do a few Mike

[@wilsoncosta7310]

PARABENS PELOS TRABALHOS APRESENTADOS

[@BritannicaRestorations]

obrigado!

[@danthetourist]

Top job buddy

[@BritannicaRestorations]

Thanks Dan!

[@nickj3368]

Well done Mike, I have twenty for you to do .lol

[@patrickjobling8676]

My goodness gracious me yes squadron leader.. now that was bigger than ben hur ..😎😁..and his charriotts

[@wilsoncosta7310]

ORECISO DE UM CARA COMO VOCE NO BRASIL

[@GrumpsBarn]

...8 minutes quick?......my missus says anything under 10 seconds is quick....

[@BritannicaRestorations]

lol!