Amazing Trick for Removing a Paint Run

In this video I will show you an Amazing Trick for removing Big Paint Runs in 2 Pac Paint. It is a method that is not well known but very effective.
If you doubt the technique, I have made a 40-minute video going into much more detail on the same method, see the video through this link.
"How to Fix Paint Defects"
• How To Fix Paint Defects
If you like this vid Subscribe to my Channel and check out my Facebook Page by clicking this link.
pages/The-Gu...

[@TheGunmanChannel]

If you doubt the technique, I have made a 40-minute video going into much more detail on the same method, see the video through this link. "How to Fix Paint Defects" kzbin.info/www/bejne/oarIoXuFjJZ2q5I

[@nsrrndr]

The Gunman what kind of filler was it again? I think I heard you say polyester, all I have in the garage is basic Bondo brand. Will i have to specifically go get polyester type?

[@irineojimenez5634]

The Gunma

[@boberson33]

Mr. Gunny please help, I don't understand how you don't burnthrough the clear on those sharp body lines at 1:00, any time I sand over body lines, even with like 800 grit, I go clean through it within 3 passes or less

[@nickydavies3947]

@@boberson33 paint is too thin

[@nickydavies3947]

This is magic i will keep this in mind chears gunny

[@tommythenice6799]

Fantastic! Very simple yet 100 effective technique, those are the reasons i love youtube, not the stupid videos, but knowledge spreading, this is priceless

[@lydiarose29]

Well said..thank you

[@scotfirehamer4247]

been painting for 30 years that's a great tip

[@spagamoto]

Fun fact: spraying your first ever clear coat at night in the dark is a _bad_ idea, but on the upside I found this sweet channel!

[@brianchristine9301]

lol, same!

[@c2thecrow]

lmao, same

[@user-fy7gt6ev5u]

Oh the good old days...I’ll be spraying again here in about a month

[@truckerenoch8824]

I like your attitude!!! People who don't take themselves too seriously, can more easily get down to serious business when they, admit folly, learn from it and share a laugh about it with others! *Improvise, adapt and overcome!!!*

[@lindz151074]

I cleared my roof at night with not much light with spray cans...I was spewing coz it looked milky after I finished but was all good in the morning 😊

[@mattslater2165]

Got three or four runs on a BMW I painted yesterday and put this trick to the test today for the first time. I was out of fine polyester filler so I used a 1K spot putty instead and it worked a treat. The guys at work thought I was crazy...until they saw the end result. Awesome tip dude. Thanks for posting this video!

[@ReverseGear]

That is the smartest thing I've seen in awhile!

[@partsroz1962]

U neeed 2 geet out more

[@shanek6582]

That was very cool of you to show us that. A lot of people are dicks about sharing secrets like that.

[@brynlpz83]

I hear you but sometimes shops ive worked at just hire dumb asses who don't give a fuck so why bother telling him stuff you figured out your self because you're not a dumb ass.Its a competitive area of work.

[@Geordo1960]

You'd get a top rate education apprenticing with this man.

[@Hotrodngaz]

Wow, I've been a painter for over 35 years now, and I've always said there's something new to learn in the trade. Thanks for sharing this trick, I'll be giving it a go the next time I get a bad run (hopefully never have to use this trick though) :) Gary (UK)

[@callummatheson2379]

Thanks for the tip man, worked great on a motorcycle fairing! Will say however to anyone doing it, you really got to watch your sanding grits and really make sure you go through the grits well or else you will leave small scratches when you polish it up. I find that 400 to take down most of the filler then moving to 600 to take the last bit off helped reduce sand scratches later when working with the finer grits before polish. Thanks again! :)

[@2102Chris]

Nice tip, thx. I have been painting for around 10 years. Never thought of fixing a run this way. Not getting many of them anymore. Keep your helpful videos coming, great job. Chris

[@TheGunmanChannel]

Yeah its not a very well known method so I thought I'd share, thanks for watching mate.

[@geopin7672]

I've done this method many years back. it always works for me. I used to practice on old doors or fenders,run the crap out of them then fix them with this technique . you'll get the hang of it. well done gunner!!

[@rockdawg1467]

gunman is the best at removing paint runs you would never know that it happened. plus I like the hail repair job he did on his own car two thumbs up

[@TheGunmanChannel]

Thanks man

[@rockdawg1467]

your welcome mate your the top dawg on doing the job right me old school we would end up striping the pannel and start again which prove you can teach an old dawg new tricks..cheers

[@MrDeathdealer79]

rock dawg

[@rockdawg1467]

Gunman have you run into any color match problems Toyota 1E7 I can't get the color to blend it's coming out a shade lighter I used dark gray prime

[@RobertSmith-wu1eb]

rock dawg yea the problem is its Toyota 1e7, try using a 50/50 blend of transparency enhancer and your color ,this makes colors blend much easier,

[@heavynumbertaco]

Man Ive been painting since 72, but I've never been afraid to learn. That is a great tip,man. Thanks from Cali. My son just taught me the cardboard trick to knock down deep scratches on plastic bumper covers. Great vid,thanks much

[@TheGunmanChannel]

JOE BLOW Thanks for watching man, I'd love to make it over to the US one day maybe we can do some killer paintwork together :-)

[@patricksantana3337]

Now this is how you do it. He correctly started with a relatively coarse grit (320) to get the runs out. Too many people start with grits that are too fine and end up either not getting the run out completely or rubbing thru the clearcoat. The worst the run is, the coarser the grit you start with and then work up from there...320, 600, 1000-1200, 1500 works perfectly. Some use razor blades initially, which also works if you are careful.

[@dukeman7595]

I like using razor blades, however, it takes a steady hand and not going to deep, or you're screwed.. If you're careful it can save a great deal of time..

[@olajuwondotson4333]

I figured out in about 2min that I couldn't use a razor blade or I was screwed 😅 This worked great

[@davidflorrimell9818]

This trick is old school. I was tought the same one 20 years ago... Keep up the good work👍

[@johnnicholas1174]

hey, yet again another great video, i watch alot of people paint on youtube as i fell you can never know enough when it comes to painting, but your channel is by far the very best by a mile, not only is your videos quality but its they way you speak to people in them, your informative and do your best to teach i find the other youtube channels the only reason they put videos up is to show how good they are and to try and lord it over people and nearly no amateur would try it there way at they haven't spoke to them in lay mans terms and nearly puts they off trying something themselves as they make it out to be so difficult im a painter and they nearly make me think its difficult what there doing even though i do it everyday, keep up the good, massive fan all the way from ireland.

[@jlp5137]

I would get it like 99 percent gone and burn through at the end LOL

[@pothead503]

Lol

[@marcwire9332]

I am glad I am not the only one thinking that!! watched the lot thinking I would burn through a good bit whilst focusing on a bad bit

[@dominicmorriestaylor6900]

i would just lob the laquer on and allow it to flow to the bottom of the panel

[@kike050584]

Always

[@badjazz271]

I would end up with solvent pops in the run and have to respray, and then with the clear being so fresh, I would risk more solvent pops in the respray.

[@Geordo1960]

Absolutely lovely technique! Works good.

[@richardunderwood5265]

Yet another brilliant tip from the Gunman, I'm turning into a gunman groupie. Your vids and how-to's are brilliant, through watching and listening to your advice, I know which gun to go for (for a DIY-er) and which refinishing option. Thanks so much.

[@scottgorman7166]

A true professional who shares his techniques and tips is a person with confidence and great self asteem. You did us all a tremendous service on this tip.....thanks

[@kevinsiffel7331]

Worked great, thank you. I've used the curved razor blade for many years and it was always nerve wracking. I tried this yesterday and it worked great , isolating the run and protecting the surrounding surface. Great thing to know.

[@TheGunmanChannel]

Its great to hear you have benefited from this vid, You just made my day with that comment. Thanks for letting me know.

[@restolad]

thats a wow from me heard of this but your the first to to demonstrate ,thanks

[@TheGunmanChannel]

Yeah its an awesome trick.

[@Chris-killinit]

hey dude, i dont do a great deal of painting, but your very cool in what you share, really deserve the recognition ! love your work,

[@johny12300]

Dude thats a very smart way to remove paint runs .Thanks for sharing ! Keep up the info for excellent results !

[@heatherdonnel5538]

Not your fault at all. While frustrating to have to start over, it's been a great learning experience. Thank you!

[@s-savage]

3:15 'NAH MATE YOU HAVNT SEEN THIS TRICK YET' LOOOL WHAT A LEGEND

[@Fartingcatfish]

Best thing I’ve ever saw to remove a run thanks so much I thought I would have to repaint a whole fender you saved my life

[@61spindrift]

Couple commenters say, ya that is an old trick. When I'm an old body man and I have not seen it before. Huge thanks. And don't be shy and not put something in video cause you think it may obvious. That is why I like your channel. It has a lot of great stuff for all us.

[@thinkingoutloud6741]

Would have been nice to know this trick when I sprayed my first car 40 years ago. Thank you for sharing!

[@MrBigbear1684]

I know quite a few professional painters here in Jamaica that need to subscribe to your channel. I'm slowly watching all your vids in preparation to do my car .

[@toejamtimmy4402]

Thank you for your video. After watching it I spent a few hours removing paint runs from my motorbike frame that I had “professionally painted” & they’re all completely gone. Saved me the hassle & expense of having it shot blasted & painted again. 🤝

[@sendheron1]

This man is Brilliant, he really knows what he's doing, love these videos👌👍👍

[@seano2112]

Just shave it with a Stanley blade first - takes about 5 minutes. Been doing it for 35 years - never let me down

[@seano2112]

Gary Allen 😂😂 I've had my fair share - mostly sorting out other people's though. And I did pack it in - retired at 50 👌

[@seano2112]

Gary Allen I know - good one too 👍

[@jimmycricket591]

Exactly..... This guy's method is time consuming and pointless !!! My best advice would be.... If you get more runs in your paintwork than Don Bradman could get in a cricket match, you should find another profession...... Lol This is Bush mechanics at best !!!

[@richf2834]

This is the difference from a painter and an applicator. A painter can fix his own mistakes

[@markh2128]

@@richf2834 well he did say his apprentice did it but yeah I agree with you.why hasn't anyone commented on the top of the door? See all the waves in the bodywork below The door handle.

[@rustyvideas8312]

Awesome video man...i wish I would have known this trick 30 years ago. It makes prefect sense can't believe I never thought of it. Thanks for putting this out there

[@richb7414]

I was a bit concerned at first until I realized what you were doing. This definitely helps visualize the area rather than gauging by feel only. Nice job on the demo.

[@Nahuelinio]

wow, awesome job!

[@TheGunmanChannel]

Thanks :-)

[@Kyle7K]

That's an interesting trick. I'm almost excited to get a run again to try it! Almost.

[@chongkelvin9390]

Thank you for sharing this valuable, useful, and helpful technique! You are the man, gun man🙏

[@Zion-jw3gm]

I've got bad runs on my bumber, everyone says it's better to get a new bumber but I'd probably still have to paint it since my cars old. This is something it looks like i can do myself. A big thank you mate.

[@themedic4050]

Use a single blade razor and tape both ends with a single layer of tape. angle the razor and scrape and cut the run out. takes about 5 mins. to do what he did here.

[@jimships]

Hold blade 90 degrees and take 80% of the run. Block the rest.

[@kylelove927]

Excellent idea! Thanks!

[@chrishaug]

yeah he could have just used the same amount of sanding to get rid of the runs and saved himself some putty.

[@jerseyjoe1677]

THE MEDIC also if you bend the blade you avoid the corners

[@DaBuGzLiFe]

The Filler seems safer and it takes just 5-10 minutes if you use glazing putty.

[@bobbyg7868]

You can do this same trick with rattle can paint. With this you can start with 600 grit. Works great. I've got 25 years in the business and I love watching your videos.

[@michaelhinchey]

what did u apply to the runs?

[@bobbyg7868]

Just cheap black spray can paint. Put 4 to 6 coats over the run, let it dry completely and start blocking. 600 until the worst is out, then move to 1000, 1500, 2000. Take your time and you will be surprised at how well it works.

[@michaelhinchey]

+BOBBY G so u don't use the glaze?

[@michaelhinchey]

+Michael Hinchey also if I use the rattle can paint, it won't settle into the clear coat?

[@bobbyg7868]

Not if it is fully cured. If it is dry enough to sand it will not hurt it. It's an old shop trick.

[@alexpsyt]

Excellent! Thanks for sharing . It's a sign of a true craftsman.

[@steven-ky2ps]

I'm glad i stumbled onto your video. this is an awesome new trick for me! Thankd so much!

[@eliseviv]

'uck yeah. Just used this and it worked. Gunny I'm having a beer in your honour tonight!

[@TheGunmanChannel]

Haha cheers mate 🍻

[@myturkishlife1777]

40+ years painting show cars , never seen this before, you always see something new ..

[@Ryan-iw8yw]

You don't paint dick pal, just shut up! So sick of idiots like you making comments people might like so you can have some kind of attention, FUCK OFF MATE!!

[@johnnycash7803]

@@Ryan-iw8yw what's up your ass?

[@budrowe176]

Ryan you’re kind of a jerk! Are you aware of that?

[@crazyharis]

If you paint 40 years of "shouwcars" why would you wanna use this trick?! A pro dont paint runners like that .. next time be homble en just leve the word "shouwcars" en use "cars" now go paint some runners on youre "cars"

[@myturkishlife1777]

@@crazyharis Ok, As you say I probably have never seen this because I don't get issues like this because of the way we paint, we don't have to paint for a finish as such because everything is wet sanded and polished, painting a standard road car working back in the garage doing insurance work then you have to go for a finish straight from the gun no time really for corrections and then of course there can be a fine line between a good finish and a run(runners) .. It was not meant to be a "look at me " because my job involves painting "showcars" it is just something I do. I do not think there is a painter on this planet that has never had a run and no body is perfect, I would like to go and paint but the covid issue is preventing this. In paint if you have an issue then the way of correcting it is the key. This method in the video is a great idea, and if the time comes (which I am sure it will :-) ) I will bear this in mind..

[@justinbruney2584]

this guy has the best tips paints ever I watched the years ago on an episode of different spray guns now I work for a body shop all from watching the gunman videos

[@CesarValdespino]

My older brother and myself are both painters he told me about this trick ... he says it actually works I will definitely try

[@ClausenLT]

I've been painting almost 17 years. I heard about this a couple weeks ago and I just ran a black quarter. It's not real bad but I'm gonna try this just to see how it works. It's kinda obvious but I never thought of it. ;)

[@TheGunmanChannel]

Its an awesome trick but if it was a real nice car then I'd just re paint because obviously it will be a flat spot without any peel when its finished.

[@ClausenLT]

The Gunman I had to wet sand the whole quarter any way because of some trash...and I was thinking about it.. I've never had a customer complain because a paint job was too flat...and when they picked up the car tonight they said "it looked better than factory"...any way...this is one of the best tricks I have ever used...I cannot believe how god this worked!!! Thanks for the video! I would have done it anyway, but it's nice to have a reference! Again..I cannot believe how good this worked!!!! THANKS!!! I wish I'd know this trick 15 years ago...wow what a giant pain it would have saved me. I also think thios will make my jobs turn out better because I won't be so worried about runs or sags!

[@brynlpz83]

+ClausenLT yeah that's how my shop is.They don't care how much orange peal is in the rest of the car they want the repaired parts flat.Doesnt make sense but when do bosses do?lol

[@TheGunmanChannel]

brynlpz83 See to me that's silly and I'd argue the point with them saying that our job is to make it look like it's never been in an accident, better than factory yes but to the trained eye it is so obvious that it's been done. Why have 3 panels that would win the concourse de elegance and the rest peely as a factory Mazda finish? It's not the aim of the game.

[@brynlpz83]

+The Gunman Yeah ill get in arguments once in a while about it but I'm just like whatever it's your shop.Still pains me everything I see the buffer DA entire panels with no dirt in them.

[@philmapockitz8216]

Gman the apprentice didn't get a sag, that was a cascade : ) Thanks for the impressive tutorial.... Cheer's

[@TheGunmanChannel]

No probs mate

[@matttallman3972]

The Gunman what brand of poly did you use? thanks

[@rodneysmith2907]

I call those curtains!

[@foadrightnow5725]

That's a helluva run, even for an apprentice! Excellent tip! Thanks for sharing!

[@southernbrew4252]

There had to be at least 10 coats of clear on that car to not have rubbed through the edge of that door wet sanding with 320.

[@christurner6774]

I have always used spot putty to sand sags and runs out. I usually start with 400/600/1000/1500/Trizact

[@TheGunmanChannel]

Yeah its the best, it got me out of trouble again today.

[@coachwhitford7315]

Spot putty is harder to sand isn't it? Is that why it would work better? Curious for my next fender/bumper run lol

[@gamesandrandomvideos2360]

When you got the shine on that door I could still see a run in the body line under the handle right by the edge

[@zoltanhortobagyi4323]

Yeah I saw that too. I guess he just wanted to record the complete procedure without making a long boring video then fixed it later.

[@kilroy776]

ya I also saw this but its still a pretty impressive way to mask out the clear you dont want brought down ill def be trying this

[@TheKebobhunter]

This looks a great trick , need to try it today . Just changed guns and and taking some getting used to . Can't believe I get better finish with a deltalyo than my new Sri pro!!. Keep up the awesome videos mate

[@buttmeister]

Excellent video. I still didn't find it like the car prep videos until after i searched for hours and went through a bunch of crap. it just popped up in my recommended videos.

[@alomonas1450]

So does this remove the clear coat?? I just got my truck painted and there are 5-7 runs all over it. They said they were gonna wet sand and buff it out, but does it remove the clear coat??

[@jamesrodriguez5799]

no it does not remove the clear coat its just to make it even with the rest of the clear

[@TheGunmanChannel]

+alomonas1450 Yes, James is right, it protects the low spots from being sanded so only the run or "high spot" where the paint has built up is exposed, preventing you from going too far and cutting through the clear.

[@alomonas1450]

Well thank yall both for the reply.

[@alomonas1450]

Well thank yall both for the reply.

[@Stillstoned1]

If they did that, get a new painter, because runs like this should never happen

[@riotdogxk9]

I did this on a black mercedez benz and it is extremely effective. I wasn't too ballsy so i started with 400 so as not to cut into it too fast.

[@thanxx]

Fabio Miguel fk 400 way to harsh. you could start with 800 and run through 1200-1500-2000 best just to stick with 1200-1500-2000

[@TheGunmanChannel]

thanxx Wrong, 400 is perfect for a run this size

[@Mikefngarage]

shoot I would have started out with 220 for a couple of strokes just to knock down the polyester filler a bit.

[@georgee686]

What a great idea just another form of a guide coat i guess . 10/10 for this one Mr GUNMAN . Hard to find tradies with pride today.

[@The1mybuddy1]

This video came up as a recommended video. I have used this trick for years. Would love to say I've never had to do it, lol, but I have. Saves so much time. I've tried the blocking with a paint stick, taking off the area and always had to declare until I came up with, what in thought was a unique idea. Haha. Awesome job.

[@MrTheHillfolk]

Ever try the razor blade trick? Be brave it does work, but one wrong move ......

[@alwaysflying6540]

I've had to do it a few more times than I would like to admit lol

[@mynewhaircut]

Do you put hardner in the filler?

[@TheGunmanChannel]

Yes mike you must put hardner in the filler then allow 10~ min to dry. The heat that the filler generates helps the run to dry out a bit too.

[@mynewhaircut]

Ok thanks

[@TheGunmanChannel]

Yes it sure does, This car I did it on was painted the same day but we dried it with infrared lights for about an hour

[@MilushkaLaChula]

can anyone tell me what type of filler this is?

[@mynewhaircut]

@@MilushkaLaChula You use just standard glazing putty like evercoat

[@chrisrawk5802]

thats really cool, I never thought/knew of this trick, Thanks for the vid ...subscribed!!

[@danadana9842]

brilliant!!!!. glad you kept the tradition / secret alive. Thanks for sharing.

[@doubledown9333]

Man that apprentice must have been on acid or something,they were some mountains on that job.

[@1Howdy1]

Pretty easy to do under an edge like that. New people tend to rotate up to hit it without realizing the bottom of their spray pattern will be a few inches closer to the work. Better to run and learn than be a total newbie and hit the edge straight on for an uneven coating. Anybody can paint, but a painter knows what causes mistakes and can fix them.

[@donjohnson4349]

I've been painting since the late seventies and only within the last couple of years and learn this trick. it's a good thing because I just ran the living s*** out of a Suburban

[@crazyharis]

You have bin painting fore over 30years and jou still paint runners? Man you suck

[@nemohoes007]

@@crazyharis ....least he can spell......👏👏

[@crazyharis]

@@nemohoes007 i speak German English Greek Belgium and little bit franch i am Belgium so English is not my language so what do you speak mister "you thought you had me on the spelling card" 😎 swim on Nemo smimmmmm onnnnnn and go look some Nickelodeon and shit 😁

[@nemohoes007]

@@crazyharis Lol salty much....and its PIXAR

[@RTCHARGER1970]

Been around a long time and have never seen this trick. I don't get a lot of runs anymore but if something goes wrong I'll certainly use this technique. Well done my friend👍

[@rimshotdk]

Thats absolutely brilliant. Thanks for sharing mate!

[@cliffordgill9052]

Yeah,you have to get runs to learn how to not get runs!!

[@coachwhitford7315]

Use fast activator, not medium lol

[@2superuser]

U can use nitro puty then can remove him with thiner.. ;)

[@2superuser]

Filler

[@TheGunmanChannel]

Yeah its a pretty neat trick, thanks for watching mate :-)

[@2superuser]

The Gunman thx for ur vids ;))

[@d-graphics9406]

Thinner moisturize paint and damage other area. This method is time taking but result is pretty fine...

[@EddieBlazer]

What a great tip! Definitely giving this one a try next time I have a run

[@normanmendonca2834]

What a amazing tip. It totally makes sense. And saves the day. Thanks.

[@Hanibul_Lecktor]

catch it wet, remove with masking tape. fast and easy as fuck.

[@mikebickers4297]

thats exactly what i do, just let it flash off ever so slightly, wipe the run away, its 10 times easier flatting a smear than it is snotters!

[@waynecossington1574]

yea m8 wot most normal people would do

[@MrProp46]

Michael Drum ... i do that also, tho im no longer a body guy im a house painter and i still is that trick

[@TheChronicRhythm]

Just like for primer

[@airmyngarage]

Exellent tip.... Thanks for sharing your technique and explaining by demonstration. Painting for 20 yrs and allways willing to learn more. Recommend your channel to all the young lads who think the old bloke (me) is talking crap when suggesting fixes. PS Gti pro lite awsome

[@madpainterken]

+phill b ...I get the same crap from the younger ones...then I show them...Who's laughing now

[@crazee6821]

Night shift can leave some nasty runs ! Thank GOD for the GUNMAN !

[@scottrobinson5594]

I used to work in a full time bodyshop, and this tip would have been gold

[@mattywollaston3996]

Love ya work mate, that is bloody awesome!!!!!! Thanks for sharing.

[@christopherjeffreys7851]

Gunman!!! Your the best!! Got a big run in a xk150 jaguar I did Saturday and was pulling my hair out thinking what the hell was I going to do. Saw this video and god damn it it work got it out and looks like it was never there. Cheers again and keep up the great videos.

[@kevintoepper2828]

I've painted houses, cabinets, bicycles, rims, everything but a car and I definitely anticipate some runs so this is good knowledge thank you brother man

[@jimmynyoike]

These old vids are packed with useful knowledge!!

[@johnmcconnell6294]

Awesome! Thank you so much for sharing this idea.

[@zcenic05]

i tried this today on some heavy runs. They came out and everything buffed out nicely.It was on something I didn't want to repaint too, Very helpful video.

[@soundworksvectra]

Always full of neat tips mate learned a few things from you

[@danmatthews3102]

Freakin' Magic! Going to use this one on my dash. Tried to hog the clear on it, and it ran like heck. Thanks for the tip.

[@beatnikbrent70]

Pretty slick! I had my doubts when I seen you spreading putty. Nice!

[@craigkeller]

Good to see you young guns developing great skills!

[@petrinipimentel8404]

Bad ass man thats an awsome tip been painting for 10 years and this is def one i want to try myself!

[@TheRolln]

Awesome vid!! Great demonstration!

[@JesusGuerrero-fe3du]

You did a great job fixing that run you couldn't see where the run was? Great video Gunman

[@theflyingmushroom8641]

I've got one run on the side of my Beamer that's been there since last year cause I've been dreading sanding it out. Thank you for revealing this magic trick!! David Blaine would be amazed!

[@Hutchy45445]

That's just genius! Thanks for sharing man.

[@themostoriganalthing]

Grew up in an autobody shop. This is the best trick i have ever seen.

[@tommyd.743]

The difference between a professional and a skilled professional. I'm impressed.

[@wesleyd.7433]

Brilliant correction technique. I really appreciate info like this and thanks for sharing.

[@shaerobins4530]

Man u never cease to amaze me man keep it up gunner

[@TheGunmanChannel]

Haha cheers 👊

[@briancooper4767]

Great tip man, you got a subscriber!

[@hinddee]

Awesome Gun! I'll remember this. thanks for sharing.

[@ronnor58]

Great job. What a great tip, thanks for sharing!

[@oofazi]

That, is fantastic! Well done mate.

[@LuisC202]

Wow this is genius. Gunny you are The Man 👨