How to Clean Carburetor Mercury 9.9 4 stroke. How to clean carburetor on Mercury Outboard.
Пікірлер: 21
@apackwestbound59463 жыл бұрын
Nice job highlighting the tiny fuel passages! I have watched many KZbin videos on this subject and this is the first time anybody made an effort to highlight these tiny idle fuel circuit passages. Being so small these are susceptible to contamination/blockage. The way you freeze the picture and highlight something in the frame and explain/offer advice is very effective. I have not seen anybody else use that technique on these type of DIY tutorial videos. Thank you!
@MaineManBassing3 жыл бұрын
Thanks man.
@erik83443 жыл бұрын
Your engine does utilize the compartment for priming. It also houses the accelerator pump. The throttle lever pushes down on a white cap that covers the top of the plunger, which pushes the diaphragm and pumps a small amount of fuel into the carb when you open the throttle plate. You can see the linkage, a brass adjusting screw, the white cap and rubber boot which covers the plunger in the opening frame (2:21) of the engine. In the picture the long metal throttle linkage cuts right in front of the rubber boot. This is to enrich the mixture until the increasing vacuum can pull more fuel because when the throttle plate is opened air rushes in first (it has less mass) and the fuel lags slightly. When this diaphragm wears out and leaks the engine often bogs down for a bit when the throttle is opened quickly. I also wouldn't bother to open and clean it unless you are having this issue or the housing is leaking fuel (the diaphragm also serves as a gasket). The engines that have a small primer bulb also use this component to pump a small amount of fuel for starting. Thanks for the video, the freeze frame and red circles are great.
@mischadiaya3 жыл бұрын
Thank you for this video. Tons of great info without a lot of b.s. which seems so prevalent with guys making youtube vids. Gave me lots of confidence before tackling my 9.9 carb. Best wishes and thanks again from Sakinaw lake B.C.
@mikereid1960 Жыл бұрын
This was an awesome video! hope my mother responds to the new gasket!!
@davidmadariaga98923 жыл бұрын
Awesome video, thanks,you saved me a bunch of money
@MaineManBassing3 жыл бұрын
Glad I could help
@michaeldean24472 жыл бұрын
Thanks for the video I have the same motor and dies when I throttle down to shift. Runs great fast but I'm confident this is my problem. Thanks
@MaineManBassing Жыл бұрын
I replaced that gasket in the carb. Ran much better after that.
@rilla642 жыл бұрын
I appreciate his video I just wanted to know was it 8 or 10 mm. I understand the gaskets in the air fuel mixture and all that depends on the year I prefer 2-stroke I don't know about everybody else out there give me a thumbs up. If you would rather have a two-stroke
@owendean16163 жыл бұрын
Culprit is usually the float valve seat
@jeffarcher61253 жыл бұрын
Great video. I have a 1993 15Hp so hope the carb is similar. I assume you replaced the gasket to fix your idle problem. I'm going to try chemical cleaning first. If I have no success then I will try and pull it apart. happy fishing from New Zealand.
@MaineManBassing3 жыл бұрын
Just ordered the main carb gasket. Its getting enough gas. Found out my impeller was shot. replacing that this weekend.
@erikalexanderwerner3 жыл бұрын
Thanks a lot!
@MaineManBassing3 жыл бұрын
I have another one on my channel about the carb.
@MaineManBassing3 жыл бұрын
kzbin.info/www/bejne/eXScmJ2GbaySaas
@MaineManBassing3 жыл бұрын
be careful tightening back into the intake manifold. Not too tight.
@JGalindo12183 ай бұрын
Can u tell me which gasket surface was taking in air
@MaineManBassing29 күн бұрын
I replaced the gasket completely and that helped A LOT.