API 6A HYDRO TEST PSL 1. Wellhead gate valve hydro test. How to pressure test a valve. Valve testing

Рет қаралды 11,573

Everything Valves

Күн бұрын

Пікірлер: 28

@vern600r 6 сағат бұрын

What a brilliant video! It couldn't be more informative thank you very much

@femsolefoot4977 Ай бұрын

Great video

@MD.RustamAli-qj6uh 7 ай бұрын

Nice video

@MD.RustamAli-qj6uh 7 ай бұрын

thank you sir

@abijarwo3678 28 күн бұрын

Do hydro test on appropriate chamber

@جونيالبطل-ز5ص 3 жыл бұрын

Great Can you provide other details about the test and The rest of the tests

@everythingvalves 3 жыл бұрын

Thanks for the reply. I plan to make more testing videos soon. They will provide more details on how perform pressure tests. Stay tuned. Thank you very much for watching.

@robbrownfield7677 3 ай бұрын

How do you torque without preventing the back nut from spinning freely?

@You-m2m9q 2 ай бұрын

Put a backup crescent wrench on it till the nut bites down a little as you torque then take the wrench off so it doesn't get stuck and finish the torque

@satyeshsetty1569 3 жыл бұрын

Very informative video, Appreciate :) but only one thing I was not clear, I believe you said rubber gasket in between valve and flange, I think it should be metal seal right? Ex: BX, Rx seal??

@everythingvalves 3 жыл бұрын

Thanks for your support. That is a good point you bring up. When the valve is going to be installed for service you would use a metal ring groove gasket. You are correct. However when we perform test on the valves we do not like to use the metal rings for 2 reasons. First the metal rings are expensive and when only function testing the valves there is no need to waste them. 2nd sometimes when you use the metal rings and torque them down. You can damage the ring groove which would then cause the valve to leak in the field. These 2 reasons are why we use a rubber or other polymer type gasket when we test. Hope that cleared up your questions. Thank you for watching.

@ahmedanwar4586 Жыл бұрын

This is slab gate valve

@haider63530 8 ай бұрын

Hi can you explain what PSL is? I didn't find a definition and I need to know its benefit. Thank you

@everythingvalves 8 ай бұрын

There are 3 different PSL or (PRODUCT SPECIFICATION LEVELS). The higher the level the more inspections, documentation and resources are required. If you search one of my other videos API 6A pressure testing procedure. I reference some of the psl requirements. Hope this was helpful. Thank you for the comment.

@haider63530 8 ай бұрын

@@everythingvalves Thanks a lot. indeed I saw another video of yours and I got it, do you have any video mentioning the performance requirements (PR)?

@binzhao3552 Жыл бұрын

Obviously, this valve was filled a lot sealant before hyd test, as to the present of sealant, it is hard to know if this valve past test.

@everythingvalves Жыл бұрын

I appreciate your comment. These gate valves utilize grease it’s a pretty common thing. If the valve truly had a seat issue grease or no grease you would see the H2O passing the seats. If you have a different method you use for these valves I would be interested to know. Thanks again for the comment.

@You-m2m9q 2 ай бұрын

@@everythingvalvesI think your method in the video is what I've seen at all the frac valve shops, not sure what he's saying... Super video, I'm so grateful for your content. Highest quality I've seen, even better than many of those cringy promo videos from big manufacturers. Excellent detail as well. Thanks again.

@vickyvignesh6194 Жыл бұрын

METAL TO METAL SEAT LEAKAGE ALLOW OR NOT

@sparksagar1 3 жыл бұрын

I guess, the hydro test is not to be done on a painted valve body, as shown in your video.

@everythingvalves 3 жыл бұрын

That is a good question. Depending on the customer requirements. It is good practice to hydro test unpainted valves. That way if there are any body imperfections you would clearly spot them. If you look in the API 6A spec it gives more details about testing. Thanks for watching.