How To Add An Outdoor GFCI Outlet | Easy DIY In One Hour!

[@JStouder133]

As a licensed electrical contractor, this is almost exactly what I do to add outside outlets. Great job!

[@jackriley5974]

You must be from Texas too??

[@JStouder133]

@@jackriley5974 Actually the other side of the country, Washington state.

[@maheshkk]

Curious, is it OK for multiple outlets to be on same breaker? How would we know if we over using inside and outside outlet at same time?

[@rafaellugo4164]

​@maheshkk if you know how the circuit is ran, the magic number is 12 outlets per circuit max.

[@heidis8713]

​@@maheshkknot sure what you mean. Most outlets don't have their own breaker. Usually it's a room or two of lights/outlets that are on a circuit that share a breaker. Adding an outlet like she did is totally fine, unless you plan on running something that will overload the circuit.

[@brendoncullinan5781]

GFCI "load" versus "line." I was taught that the "line" is connected to the source of the power to the outlet, and that "load" was for any additional outlets added downstream from the outlet. Now that I watched it again and listened more carefully, this is actually exactly what April said. But is so easy to get these confused, so pay heed, grasshopper, to the lady in the ARIAT threads. She knows of what she speaks.

[@brianpimental2948]

Hi April, I have a few things. 1. Is the Gfci needs to weather resistant. 2. Today you need to ARC Fault the whole circuit now that you added off an existing circuit. 3. You must have at least 6-8” of wire from the back of the box for splices. All of these are in the NEC code book

[@MrBluelock]

1) Tamper resistant as well 2) Not required. There is an exemption for when a branch circuit is not extended more than 6ft. 3) 6" of free conductor with at least 3" being able to extend outside the opening.

[@MrTarfu]

Yeah I was thinking of that as well, probably not a good thing to promote something as a how to that goes against code since most people following won't know.

[@thebluelunarmonkey]

hopefully her inspector isn't a subscriber so wouldn't know it's not original :) and um, this isn't the first time she's added on her electrical. "Oh yeah that was there before 2002" and stick with it.

[@markconger8049]

I’m no electrician but what I read is that arc fault circuit breakers are required in most spaces in a dwelling so it is likely a fairly recently built home already has arc fault protection.

[@brianpimental2948]

@@markconger8049 you are correct but, this rule took a long time to be adopted but states. Some states still have not adopted this in full.

[@frigginpos]

Hi April, if you put the GFCI outlet on the inside wall, it will protect the wires feeding the outside outlet (non-GFCI), as well as the outside outlet circuit. This way, if the wires get wet or go bad to the outside outlet, everything is still protected.

[@robertbeltowski2819]

Frigginpos, That is true but she will find out that the inside box is to small for all the wires and the GFCI outlet. My question is how did she end up with a 20 amp outlet......it's not a dedicated 20amp circuit. If I was to see that outlet it indicates that it is a 20amp. circuit dedicated. The circuit she connected the outlet to is a kitchen/ dinning room 20 amp. circuit. Yellow NM cable=20 amp. Also April next time you install an duplex outlet in and old work box (the one you used outside) break the 4 little ears off the corners and the outlet will not hold the cover off the wall, the box screw location is recessed for this. Great job young lady.

[@davidmiedema2950]

I love the electrical inspection cat

[@taradaves3096]

Sgt Sparky on duty

[@janetyeoman1544]

Mr Manx

[@johnsullivan4741]

Makes a big difference having a power source close by on the inside! Made your project easier!!!!

[@AprilWilkerson]

Absolutely! Thanks for watching.

[@crabkilla]

Nice - I would pay attention to air sealing with spray foam in a can. These exterior electrical outlets are major air leak culprits.

[@thebluelunarmonkey]

AND BUGS!

[@stevewaybright1933]

What about that power strip ?....probably better use a cord grip and wire straight from the outlet box to the inside of the dog house

[@kpmathis71]

One concern for summer (if TX is anything like GA), wasps! They seem to love one of my outdoor outlets; it gets a lot of sun (the untouched ones do not get any Sun). Once they move in, it's hard to open it to hit them with wasp/hornet spray, but you don't have to. Spray the clear plastic shell & let it run around & down. This "gases" them enough to make them fall out. Another dose finishes them off fast. Before the wasps move in: open the lid & stick a bit of packing tape over the hole the wire comes through @7:00. I leave it sticky side out/down and use clear tape; they haven't figured this out & around it yet. You'll have to remove it to use the plug again, but this works. I've thought about 3d printing a stopper or even trying golf ball or something. Tape + months of Sun = goo. Well done as always. Enjoy the work you do.

[@curtfatherree7474]

I've done a few of those myself over the years, and not only did I do them pretty much the same way you did, I've also done a couple that were connected to an existing GFCI on the inside. I've also done a couple where I was able to add a new circuit to power them and for those I decided the best thing was install the GFCI in the power panel. Along those lines you can also add something called 'arc fault protection' which in some cases will often trip even faster than traditional GFCI's. Something else I learned along the way was to use some painter's tape on the outside wall so you'll have a place to make any marks you need without actually writing on the wall.

[@AprilWilkerson]

Awesome! Thanks for sharing and for watching.

[@fritzwang6300]

Excellent content topic April. Just two comments. Current electrical code in my area requires that the GFCI outlet on an open porch also be weather resistant. These will be marked WR or TWR. Also, I would break off the 4 "ears" on the outlet yolk before installing it in the box so that it will recess nicely. You can see in your video that they bend outward slightly. This would just give you a nicer, more professional installation.

[@lordgarth1]

Yea but funny to then plug what looks to be a cheap indoor extension into it.

[@michaelmehl4024]

I wanted to mention removing the ears, but Fritz Wang beat me to it.

[@fauxque5057]

After having several outdoor gfci outlets catch fire after years of water intrusion my advice would be to move the gfci outlet inside and then use the screws to make the outside outlet also protected. Or use a gfci circuit breaker for the circuit in your circuit breaker box. But they cost more money than a typical gfci outlet.

[@fritzwang6300]

@@fauxque5057 Fire?! That may be why my area now requires all exterior GFCI outlets to be weather resistant (WR).

[@TomCee53]

This particular cover can also use the mounting screws for the outlet. Before tightening the outlet screws, slip the cover on using the slotted holes. Also, I would have caulked around the box for an extra air seal.

[@johntotten4872]

It seems the hardest part of this job was keeping your kitty out of the middle of things. Great video April.

[@AprilWilkerson]

It really is! Thanks for watching. :)

[@JCWren]

One way to avoid the risk of hitting the romex with the drill and saw would be to use an oscillating multitool.

[@djamelhamdia134]

Agree, it is the safest tool ever.

[@MyClutteredGarage]

I was thinking the same. Such a handy tool!

[@tractortalkwithgary1271]

@@MyClutteredGarage ,the first time I saw one of those, I thought it was a complete joke. Didn't take long to make a believer out of me.

[@MyClutteredGarage]

@@tractortalkwithgary1271 me too!

[@clemsmith2253]

sorry, I couldn't hear you over the sound of my oscillating multi tool. Whadya say?

[@LetsGoFishingSoCal]

Quick tip, use a multi tool to make the cutout. Less chance of damaging any wires. I know the siding will wear out blades quicker but the multi tool is great for that rope of work.

[@stevewaybright1933]

And blades aren't that expensive

[@LetsGoFishingSoCal]

I order my blades from Amazon you can get them for a out $1 each

[@keithwilliams938]

Thanks. April, I got it done. Took quite a bit longer than 1 hour. Your video didn’t include working around Tyvek and insulation, and the possibility of a stud getting in the way. Our cat helped too!

[@jimmckeon1129]

How did you handle the stud that got in the way?

[@keithwilliams938]

@ I thought I was over far enough to miss any studs, but once I cut my hole, there was a bit of a stud in the way. I just sort of shaved and chiseled away enough of the stud so that my old work box would fit in the hole.

[@Lucky_22317]

I had remembered seeing this video shortly after you posted it. & now I’m viewing it because I’m going to install my own. Don’t worry my dad was an electrician for 44 years

[@MyClutteredGarage]

Nicely done. I kind of hate those “gate type” boxes. You can, however, open them from the inside with pliers if they have a fin. Happy dog. 😄

[@ricknplano1401]

As always, love the video. I put a heat pad in the expensive doghouse I built for my two golden retrievers. One morning, heard the radio say it was 5 degrees. Looked out and my retrievers were blissfully asleep on the concrete patio, ignoring the dog house with warm pad. :-)

[@Johnthedagger]

Our Golden will go outside when it's 10 below and nap in a snowbank. Not sure how they make it through summer sometimes but best dogs ever👍

[@happyzahn8031]

Dogs being dogs...haha 😁

[@DavidShinabarger]

This is great. What's the best way to finish waterproofing and air sealing it? Expanding foam + caulk?

[@CdeL-qs7cy]

Always nice to have an outdoor outlet. The outlet itself is nice and weather proof, but the extension cord doesn't look outdoor and is positioned with the outlets facing up (so rain might be able to get into). Looking forward to your projects!

[@mv-db4463]

Great Video !!! Not an electrician so "grain of salt": 1) Attached your pigtails to the outlet first and then into the connectors inside the walls. It is easier to connect the pigtails onto the outlet in your hand than after the pigtails are already connected. 2) Only on the INNITIAL installation of he GFCI outlet, you MUST "Trip & Reset" the GFCI button to "SET" the outlet in the (LIVE) position. The GFCI outlets come factory set in the UN-set (OFF) position. 3) ALWAYS use a GFCI tester ($10 or less) after adding, replacing or working on ANY outlet. (Wires/ outlets can break, come lose or be wired incorrectly) It also verifies if you properly wired the outlets AND if the "TRIP" function on a GFCI on the outlet is working. Again NOT and electrician, but have done hundreds of electrical receptacles and switches. Hope this helps !

[@steelshade]

Good to see the 'Inspector' checking your work.

[@AprilWilkerson]

Yes, I have to watch it. She is ruthless about infractions. :)

[@allenwilson9656]

Happy New Year , April And to all the viewers 🍾 🍾 🎉 🎉

[@AprilWilkerson]

Happy New Year to you too! Thanks for watching.

[@efixx]

Lucky 🐕 Dog - heated pads!

[@davidduvall4655]

Ahh the mandatory cat scan. You might want to invest in a non contact power detector really handy.

[@Zogg1281]

I know that your porch is sheltered but I noticed that you have your dog heat pads plugged into a non weatherproof extension cable, which is then plugged into your new weatherproof box...... which kind of defeats the purpose of the weatherproof box in the first place. I have seen weatherproof extension cable boxes that you could put the extension cable into which would give more protection to you and your dogs. Otherwise it's a really nicely done job. Hope you all had a wonderful Christmas and New Year 👍👍👍

[@ultimate1576]

The "gate" style box isn't actually supposed to be knocked out. They are there to grip onto the Romex.

[@paul4800]

Integral clamp

[@phonedave]

The knockout style is only supposed to be used with new work, not old work (retrofit). A single gang box (only single gang) does not need an added clamp or an integral clamp if you can attach the wire to the stud (as you can with new work). Since you cannot get to the stud to fasten the cable with this retrofit work, then you need to provide a box clamp. I would say this rarely happens, but that is the code and the right way to do it.

[@justinhittinger]

Awesome video! Quick tip: skip a step by using screws that come with the receptacles to attach the box cover the slot below where you screwed it in. Leave the screws slightly loose (or remove) slide the box into the larger diameter of the double slotted holes above and below and tighten into the smaller side 👌🏼

[@phillipbetts9070]

In our area the electrical code requires that outside GFCI outlets be on their own breaker. This may be different from state-to-state or province-to-province. Always check your local codes.

[@jimzimmerman5288]

Phil, your city has to have an ordinance in place to justify the need for a breaker on outside GFCI outlets.

[@phillipbetts9070]

@@jimzimmerman5288 Actually it's the whole province of BC, no exceptions, I just went through an electrical inspection.

[@mikecurtis2585]

Great job. You can always use more outlets outside. Thanks 😊 🙏

[@AverageCarGuy]

You can never have enough!

[@FollowHereThere]

your cat assistant is my favourite part!

[@kipcarroll5644]

Just so you know for the future, April, the blue plastic electrical box with the nails on it are new construction boxes. The ones with the doors or wings are remodel boxes. Those wings slide behind the sheetrock and the screw tightens them against the back of the sheetrock. Thx for the video. I'm sure it will help many out there.

[@shopart1488]

Old work and new work, I really think she knows that. Demonstration only!!!

[@allcleanenterpise]

I always have mad respect for a lady that wears work gear and is savvy with power tools and with a electrical meter in here pocket.

[@Terry_1111]

Excellent video, April. Your cat reminds me of mine - always wanting to help with any project! Hope you have a wonderful 2022 filled with many blessings and abundance! Thanks for all you do!

[@AprilWilkerson]

Thank you! You too!

[@LogicallyInsane1]

Avoid using an impact to tighten the screws on the receptacle. Or at least go behind with a regular screwdriver. I've found that no matter how many ugga duggas i give, the screw is almost always able to be hand tightened a little bit more. Loose connections can cause issues down the road. Otherwise good job. Only other note would be if you put both probes into the tamper resistant receptacle at the same time it'll actually insert into it. But either way works.

[@jeffhenderson934]

Thanks for the video April, very helpful. I bought a house built in the 80’s with just one outlet for the raised deck. Just one outlet for the 10’x30’ deck. And of course it’s near the door. I just finished enlarging the deck to 24’x30’ and with my OCD I thought, “You know what the deck needs now? Multiple outlets, in more accessible locations!” (Phone charging, speakers, a place when my dad shows up with his electric ice cream churn, etc.) I’m going to follow your video, add at least 3 GCFI covered outlets, run the romex under the deck with schedule 80 pvc, and 90 degree up through the deck to the 6”x6” posts. Long story short, I want to go from the existing outlet, following what you did and continue from outlet to outlet 3 times. (Unless you tell me different. LOL!)

[@thebluelunarmonkey]

April, you're also fulfilling the electrical code requirement to install at least one weather-resistant GFCI outlet (no higher than 6 1/2 feet) within the perimeter of each porch/deck accessible from the inside of your home. You have one on the front, now your back is up to code too! There's no minimum height for the box, btw.

[@amylea3980]

Kevin- your comment was a year ago so I hope you get this. What is the verbiage of the code and is it national or by state?? We are buying our first home (in SC).. It is a new build. There’s an outside outlet on the back of the house, but NOT inside the screened in porch. The manager of the build says that there is not an outlet on the plan for inside the porch. It shouldn’t be difficult to install, but I’d love to be able to site the code and put it back on them! The porch has a ceiling fan rough-in and two walls have an adjacent outlet on the interior of the home. Are they in violation by NOT adding an outlet?? Will try to send a photo to this thread. April… this is my first time catching your site. I don’t even know where to find local codes. I’m in Charleston county, SC. The home is on Johns island. Thank you to ANYONE that can educate me further!!

[@amylea3980]

Nope can’t put a photo anywhere. It’s a fully screened in porch off the back of the house. It’s 12x10. If exiting the kitchen-- standard swing door- and stepping into the porch, the exterior door is then on the right about 7 feet ahead. The current outside outlet is on the house 6” up and about a foot from the screened enclosure, but as described, the ext door of the porch is at the other end. As it is now… running an extension cord into the house or to the outer outlet will not be ideal…or the best plan for my hot tub installation. Shouldn’t all screened in porches have at least one accessible outlet? Thank you!

[@thebluelunarmonkey]

@@amylea3980 NEC 210.52(E). There's code variants by year/state/local of "from grade" "standing on grade" etc. You'll have to see if your local has exemptions or whatnot. The screen may interfere with 'readily accessible' aspect of the outlet. I have two rear outlets, one on the outer wall accessible from standing on the ground and one on the deck, between two back doors

[@BearCreekWoodworking]

The push connectors are something new to me. Seems like I always learn something new from your videos April! Thanks! 😃

[@bacillus9]

Wago connectors are fast and easy but the wires can easily be pulled out/become loose and cause an arc, which is a bad thing.

[@DocHemi4268]

Many places, those are against code...and i was taught - they are a big NO

[@germandude5181]

@@bacillus9 They really can't. They have incredible grip strength (both the 221/222-lever series, as well as the 273-series push-in connector for solid wire). You'd need an exorbitant amount of force to remove a conductor that has been properly stripped and pushed into the connector. They've been the standard in Germany (and most of mainland Europe) since the 1970s/1980s and very rarely cause any issues - and all those issues can be marked up to user error.

[@yveserichot2304]

Have a wonderful 2022! Keep your nice work & smile 😊! Thanks of sharing your thoughts & projects!

[@01arron]

Good to see you back April. I’ve missed your normal day to day jobs. Happy New Years to you and your family

[@Belg1970]

In areas where a lot of snow piles up I try to install exterior Receptacles at least 24" off the surface below. Also go slightly higher than the interior outlet when cutting it in, so as you feed the wire in from there it will be easier to grab it, and not have to twist it.

[@chelolelo]

Good Job, Would you say silicon is needed on the backside to seal that connection up?

[@markjohnson5556]

April, I had a question about your inside wiring. I wasn't clear on which wires went to load and which went to line after you had installed the outside outlet. It looked like you spliced all three blacks then ran another black wire to load. How does that work with the original black line wire? I hope that made sense.

[@jimmyjam838]

Why did you drill holes in your siding rather than using the keyhole slot provided in the weatherproof box?

[@bacillus9]

The keyhole slots are only for attaching the cover to the receptacle via the screws used to mount the receptacle to the cut in box.

[@justinwalker4506]

@@bacillus9 is that not what she did? I mean you said they are for attaching the cover using the receptacle screws. She attached the cover just added screws lol I use the keyholes for installing bubble covers. Way quicker and nothing wrong with it.

[@bacillus9]

@@justinwalker4506 Ok. My mistake. She drilled the holes in the siding because the screws used to attach the in-use cover are so long that they would run into the siding. Alternatives to drilling into the siding would be to cut a slightly larger hole for the cut in box so the screws won't hit the siding, or cut the screws down to a shorter size. And as mentioned in other comments, definitely clip the receptacle ears off before installing it in the box so the GFI will sit flush against the box.

[@justinwalker4506]

@@bacillus9 I wasny trying to be rude or call you out. It's just I always use the keyhole holes for attaching outside covers like these. Didn't know if that was not plausible or what

[@btd2516]

Is the Tim Allen show "Assembly Required" coming back and will you be on it again?

[@AprilWilkerson]

Hmm. Stay tuned for a big announcement soon. Thanks for watching.

[@justinwalker4506]

Everybody has to give there NEC code tips. This is an existing, not new construction job. It is gfci protected. It is her house. She did an amazing job. That's my input. Thanks

[@scoutmaster33]

WAy to GO with using connectors per code instead of trying wiring all those loose ends into the outlet. Just a note for others that might mount the box horizontally they need to have the hinged side on the top.

[@donow8464]

is the heating pad outdoor rated? I dont see a ground plug on that unit. Also Id turn the extension on its side to avoid water infiltration.

[@BigAlWillis]

nice job. reading all the comments of course everyone does things different. it's adding a plug & it works that's all she needed it to do.

[@AprilWilkerson]

Thanks. :)

[@shaunmurphy192]

😊 did you do this yourself did you have to get help from them and what do ya do if the inside box are old and metal. I want to do this outside on my house one by my front porch and then the other one the left side of the house. Is it easier to do that yourself and cheaper than hiring someone. 😊

[@firejack007]

As an extra step it would be good to seal around the outlet before putting on the cover even though it has a foam back especially for those in the country in cold weather.

[@lorraineanderson149]

Do you need to silicon the outside box that touches the house as a water seal?

[@jcwilkerson5563]

Nice...it also reduces the need for extension cords for your holiday lights and much safer!

[@AprilWilkerson]

Yes indeed! Thanks for watching.

[@olivercole6758]

The wire you pulled outside, was that extra wire you installed yourself or extra wire pulled from the wall that was already in place?

[@justwork_hvac]

Great video thanks for sharing..what is the black mask called

[@courtneyvance5977]

Did you reconnect the white wire to the original indoor outlet? Or just the black?

[@grumblycurmudgeon]

Very clear instructions! Not sure I totally agree with proceeding to plug in a non-weatherized extension cord and stuff it behind the doghouse, conductor slots facing up, but at least you've got that gfci.

[@arnulfob3454]

By far this was the best video that I found , thank you for the posting.

[@AprilWilkerson]

Thanks! I'm glad you found it useful. Thanks for watching.

[@ScaryFast]

I'm going to replace an outside outlet in the spring with a GFCI outlet, and likely add at least one other to the back of the house, but in the meantime I found out you can buy a GFCI adapter! It just plugs into the outlet (one plug, but it's big enough to cover the entire outlet) and gives you the test and reset buttons right there, with a short cord to plug an extension cord into. I'm using it for a roof de-icing cable and to plug my car in on super cold days.

[@glencrandall7051]

Nice work April. Thank you for sharing. Have a great and safe 2022.

[@sparkythebuilder]

FYI code requires the wires in a box to be at least 3" past the face of the box. It appears that April cut the wires too short. Also, it is not required to use a 20 amp receptacle on 20 amp circuit.

[@Sean0526a]

yeah, she did so well right up until she cut those wires. I get the plan, but it wasn't code, maybe in her area, I'm not familiar with that, but in general no.

[@lifehackertips]

That’s why she said at the end to hire a professional because she’s not a professional.

[@shawnsipos6217]

Did you have to add wire for length? what if you cant go exactly across from the interior to the exterior.??. Do u have to run all new wire or can u add wire to the existing ? How do u add wire for more length???

[@stephanieellis4646]

Love your diy videos on running extra plugs, as I live in a older home (land lines where ran on the top of sheet rock, which we no longer use, so we have removed most of them,even phone jacks were attached to the outside of base boards) and I really need an external plug in the front of my home, unfortunately I have brick so might have to put under the eve of front, and that's okay because during the holidays I can use it for sure, I usually have to run an extension cord from inside through a window....... looking forward to watching more of your diy's 👍👍

[@caseyjensen1733]

Any waterproofing needed?

[@jrambassn6758]

Is the same thing with an exterior light?

[@tysnasty2]

Thank you so much for such a simple video. After watching this I’m confident I’m able able to do this exact installation. 👍🏻👍🏻

[@AprilWilkerson]

Glad it helped. Thanks for watching.

[@marsnyder2610]

Even if I know I can do this, I still prefer the service of a licensed electrician. Good informative video. Thanks.

[@RS-Amsterdam]

Finally, the dogs are getting TV !!! ;-)

[@sjpropertyservices3987]

I enjoy your videos. I did not see you sealing around the new box with spray foam. Is this something you did later to help with drafts, heat/AC loss, or insects?

[@KyleHarrisonRedacted]

Hi there, this was super helpful to see that it’s not this gigantic job. Seems you had a lot going in your favour though, where I’m not quite so lucky unfortunately 😅 I have no outlets outside (Hence why I’m here) but also no indoor outlets on the same wall that separates exterior from interior. What’s the strategy there?

[@jewllake]

That cat....LOL it really wanted to help!

[@the0prynce]

This is fantastic. I think you just changed my life.

[@michaelhenderson5098]

Every job needs a supervisor/inspector. :) Thanks for posting. Happy New Year.

[@molivar5]

did you use the same wire from the inside or add a piece? I'm confused, sorry.

[@stvcobbs]

Great video. Thank you for giving your ideas. I see your playful little kitty is your helper. My cat(s) also help me with any projects I do.

[@AprilWilkerson]

Yes, Walker is quite the Supervisor. Has to be in the middle of everything. Glad you enjoyed it. Thanks for watching.

[@piratetaylor29]

April, I missed something, are you grabbing the existing yellow Romex that is connected to the inside outlet? Or did you run a new line which now that I think about it, defeats the purpose of locating an inside outlet right? So you disconnect the Romex from the inside outlet to run to the new outside outlet, right?

[@thematthewlondon]

the yellow romex is a little pigtail off of the inside outlet.. so inside outlet works as it used to, and you're just adding an additional wire that connects to the outside outlet

[@piratetaylor29]

This is exactly what I'll be doing at my house. This is so much easier than running a whole new line from the breaker box. 👍👍

[@catgynt9148]

Thank you for sharing this insightful video April. Wishing you and your family a blessed new year. It’s wonderful seeing your cat trying to help you with the wiring. It’s nice getting your furry kids involved in the family business. Greetings from NE Ohio near the southern shore of the Great Swamp Erie. Cheers

[@AprilWilkerson]

Thank you so much! Same to you!

[@Old-Man-from-Augsburg-Bavaria]

I wish you a happy new year 2022, may all your wishes and dreams come true, may God protect you and your family, with best regards Ernst from Augsburg / Germany

[@slappadabass3290]

-To test a tamperproof receptacle you just have to evenly push the leads in together -Get yourself an oscillating tool -There was no need to use the extra screws to secure the box. If the hole was cut correctly the tabs work great

[@robertbateman3665]

I agree with Brian Pimental's and Marcus Olsson 's observations and would like to add one more. You used an extension cord to plug in your heater. The cord had 3 sockets to plug into. I would not recommend using this outdoors. Moisture can corrode or even short out the outlet. Sometimes the short will not trip a circuit breaker and water will actually boil and overheat the outlet. Single ended extension cords are safer outdoors.

[@mister-action1]

Adding a few things. Don't line up the outside box with the inside box. There's not enough depth for boxes back to back. You want to use the same gage wire, and I just drill a 3/8 hole to pass the wire from the old box.

[@AverageCarGuy]

She didn't line them up. They were offset by a few inches just as you suggested.

[@kennethschoen7796]

@@AverageCarGuy I think he knows she didn't. He's just commenting it because she didn't say not to line them up in the video and that's helpful to know.

[@mister-action1]

@@kennethschoen7796 That's correct, Thanks!

[@justinwalker4506]

You can line them up just have to use a surface mount t-11 weatherproof box for the outlet. I do this all the time especially adding to brick homes. Chase nipples and t-11 boxes are my go to

[@danielfaupl520]

What brand and model of tractor do you have?

[@jonkocen]

I did this for my daughter so she could work outside on her back patio. Easy-peasy too

[@AprilWilkerson]

Awesome! Thanks for sharing and also for watching.

[@KellyBurnham]

You can cut the measuring by using an aircraft (long) drill bit and drilling thru the back of the indoor device box to the outside, bingo - outside box location done.

[@kestutisk9397]

Great job April nice to see you again🙂

[@jacobsonleland]

April, I have been watching your you tube channel for a few years now. Their are Hundreds and Hundreds of You Tubers and Video's of a lot of the products and projects you have video's of too. But I always enjoy viewing your videos much more especially when it is something I am online trying to refresh my memory on or learning for myself not only because you are such a Beautiful woman but also because I can relate to the way that you explain in the video what it is you are doing . I think you do an excellent job of not only showing what you are working on or with well in the videos but also how well you can relate/ explain what and why you are doing it. The Being Beautiful part is a Bonus . Thank you-Laterz Leland

[@thelongs5698]

Extremely helpful. Can the same be done for an external junction box needed to be added for a hard wired security camera? Thanks!

[@OneSmellyTaco]

2:47 those two boxes with the "tabs " are also very much different that was poorly explained. The one with nails is a new construction box and the one with screws is an old construction box. Thats a major difference when buying a box (or having to do a second trip to the depot store). The reason you can punch the one with nails in is because its assumed that one is already mounted on the wall vs the box with screws is usually mounted after the drywall is up, so you can feed it from the back of the box. Also, the new construction box is mounted on a structure (i.e. studs) vs the old construction box can be hung feely on the drywall. Long winded comment, but again, a very important difference that will save you time, money, and a trip to the store.

[@JS-.-]

Are those redwings that you’re wearing?

[@EverythingIsAJunkDrawer]

The other style tab "from the outside only" can be pulled in from the box. Just remove the outlet and pull from the inside, they have a T shape to the tabs, the "fin" can be grabbed with pliers and or you can pry them inwards.

[@warrendconner]

I want to do this on my back patio, but the outlet I want to tie into was seal with spray foam. So I can't just push wire through like you. Any suggestions?

[@suearmstrong3404]

April, maybe I missed it but where did you get the Romex to run to the outside outlet??

[@waldenli5750]

Do we need permit to do it?

[@brentjackson2312]

Good video that resolved a couple questions I had about a similar project. Very accessible. Please remember safety glasses when using power tools. That spade bit through fibercement siding throws chips that could blind you.

[@SoulFU2]

Another great video April, I can't wait to see what you have in store for us in 2022!

[@AprilWilkerson]

Thanks so much!!

[@TXH1138]

I have brick outside, how would you handle that?

[@keving1776]

Better than videos I seen of dudes installing outdoor outlets. Nice job.

[@dddube12]

Your Cat love’s you!!!!!! Lucky pups!!!

[@bradfaulkner971]

Awesome video, you did a great job. Excellent step by step video. Watching how you work... you have good skills. Only cringed when you trimmed the wires in that receptacle box. Keep them no less than 6 inches from back of the box per NEC.

[@tdavey5599]

I luv your signature wave

[@AprilWilkerson]

Thanks! :)

[@NMcCauley]

No caulk or silicone to prevent unwanted insects?