How to assemble a Briggs and Stratton Engine. Engine is a Model #12H802-1534
Пікірлер: 48
@gabrielwilliams10056 жыл бұрын
Oh my god thank you no body else has this engine on KZbin and this is what I need
@edardon164 жыл бұрын
exactly
@AlchemistLair11 жыл бұрын
Excellent!! Don't forget to turn on the camera for those of us who can't get enough of the kind!!
@AlchemistLair10 жыл бұрын
Yes, when you lap the valves, you lap the valve seats at the same time. If not shown on this video it's in another of the series.
@HumbertoUrbinaChocron18 күн бұрын
Hello friend, cordial greetings from Venezuela 🇻🇪 Please I would like to know the torque that the connecting rod, the crankcase and the cover or chamber of the 3.5 HP BRIGGS STRATTON engine should have, thank you very much for your excellent and very detailed explanation, congratulations.
@TheWreckingYard12 жыл бұрын
Looking good, great advice!
@abdulwasihabdulsalam40842 жыл бұрын
thank you sir ...great tutorial👍🙏
@carlingcarling81467 жыл бұрын
thanks for sharing
@vernonbosshard93179 жыл бұрын
I'm rebuilding a 6.75, the block and related stuff are the same as yours. I'm replacing a bent crankshaft on a almost new mower. I didn't remove the gov arm, I assume there is no seal or anything to replace there.
@Lorddarthvader170110 жыл бұрын
Did you Lap the valve seats?
@georgesg106 жыл бұрын
I have a OH 160 Cast iron block , I would like to rebore the cylender ?
@clemensschmitter761611 жыл бұрын
very good!!!!
@AlchemistLair11 жыл бұрын
Thanks for pointing that out!! I made an annotation of the video itself.
@krankyskush104511 жыл бұрын
good job i am about to start a rebuild on a 19hp briggs maybe not a full rebuild i have crankshaft seal gone bad
@carlodonnell146 Жыл бұрын
if you use too much of assembly lube won't it stop the oil from entering the bearing? just a thought that came to mind
@carlodonnell146 Жыл бұрын
are the pistons marked like a big engine or how do you decide which way to put the piston; I notice that the con-rod is shaped a certain way?
@ugenious017 жыл бұрын
Yea where is the oil dipper ??.
@markinnam69918 жыл бұрын
1 thing missing, valve to piston timing, tdc on exhaust stroke with marks aligned
@AlchemistLair8 жыл бұрын
Sorry, I'll have to watch the video again to see where it dropped off
@harrrytoool13913 жыл бұрын
Thanks for the video I’m frustrated that I can’t find the torque conversion number from American to Newton metres. Anyone can help out I’d appreciate that. Robert UK
@eudysdelossantos76525 жыл бұрын
Maestro disculpe que le escriba en español pero no se inglés, me gustan sus vídeos, tengo una podadora briggs stratton 140cc después de un rato trabajando tira aceite por el filtro del aire
@sebomba4164 жыл бұрын
Buenas noches y disculpe no se inglés. Me podrías decir el torque de viela, tapa de válvulas o culata y la tapa del blok desde ya muchas gracias.
@pedroadrianza16922 жыл бұрын
Quisiera saber con gráficas cómo corregir la descompresión de un motor briyet &start[o6.5
@paulthegame8611 жыл бұрын
verry good information
@manuelfragos65822 жыл бұрын
Ver em português
@motorcyclemike4311 жыл бұрын
You should tell that its "Inch Pounds" on the lower 2 rod bolts!.......not foot pounds for those that dont know the difference !
@michaelstuckey179410 жыл бұрын
what kind of oil did you use for the oil rings? Is cutting oil ok?
@AlchemistLair10 жыл бұрын
I always use straight 30W NON-DETERGENT motor oil for the break-in of any cylinder. You can buy a cheap quart at any auto parts store (AutoZone).
@dustinpool10 жыл бұрын
does the pin have to be glued in like that ? I thought they had to just set in the hole so that if the gear ever caught and spun the pin it wouldn't break the block ?
@AlchemistLair10 жыл бұрын
Not sure what "pin" you are referring to but I'm not using any glue. That red stuff you see is assembly lube.
@lindafoster8094 Жыл бұрын
I have a motor that needs a rebuild. My husband can't seem to find a replacement motor the Motor # is BriggsandStratton 09P6020076F1. Do you rebuild motors or know someone who does? The engine went on a TB_100 TroyBilt push mower built in 2019. I would appreciate any information you can provide. Thank you from Linda and Frank Foster
@olivierbeucken66717 жыл бұрын
Can you also cover it in oil instead of using the red stuff?
@worthbiggles2 жыл бұрын
Anything that lubes will do the trick
@imbrandon167 жыл бұрын
how the flying fck did you get the old piston off? BOTH FKN BOLTS on my piston connector rods freiking stripped, i tried a 5/16, and a 7mm or 8mm i forget which, but both stripped...
@tigertrucker39718 жыл бұрын
nice job,what paint did you use looks well cool
@AlchemistLair8 жыл бұрын
+Philip Hoad Autozone gloss black spray can. Cheap and Quick!!
@tigertrucker39718 жыл бұрын
Any primer,by the way got all these videos on my computer ,watch them as I am on bus in highlands of scotland
@AlchemistLair8 жыл бұрын
I use a metal etching primer - spay can
@butthead19484 жыл бұрын
Just so everyone knows when you torque down the rod bolts it's inch pounds not foot pounds he forgot to mention that
@manuelfragos65822 жыл бұрын
Ver em português
@scoiattolopigro3083 Жыл бұрын
engine without bearings in the main tree? WTF in that?
@stevesmith60583 жыл бұрын
I don’t think he can multitask he stumbles his words too much
@paulthegame8611 жыл бұрын
R O M A N I A T H E
@jimanders66666 жыл бұрын
????????????????????????????????????????????
@joncj0110 жыл бұрын
get a new camera its too fuzzy[not focused] on the images an stay centered ,hold still ,getting dizzy just watching