At Transmission Shop for 8 MONTHS?? Fixed in 15 MINUTES!! (Mazda 6 Stuck in 3rd P0328)

[@clintprice2123]

You were so worth that 3 hour drive! Nice job Ivan!

[@PineHollowAutoDiagnostics]

Customer was very pleased... And surprised that the car was repaired within an hour of getting dropped off 😅

[@clintprice2123]

@@PineHollowAutoDiagnostics And he was back home in time for dinner too!!!

[@jamesbruno5896]

Wow nice diag Ivan!

[@Graham_Wideman]

@@PineHollowAutoDiagnostics Wait... you charged the battery, diagnosed the problem, while shooting a video, AND got the knock sensor ordered and delivered (!!) all within one hour? OK, I'm much more impressed with that than the bit about replacing the component that the trouble code said to replace 🙂. (OK, I do get that the moral of this video is to rigorously question one's assumption that Problem B couldn't possibly have anything to do with Problem A.)

[@dominicwebb8000]

Over many years I’ve realised that Google is your friend - as you said it’s vital to search on the correct terms, typically it’s going to have occurred before. In my 20’s I worked for HP as an engineer, my Parts controller (storeman) could diagnose faults on products just from the parts usage he saw on his parts system. If you asked for something obscure he would as ‘what makes you the only engineer in the world to request that part’!

[@oneeyedjack4727]

I've found that more manufacturers are tying in simple faults that normally wouldn't affect drivability to more critical functions just to get the owner to get the simpler things fixed. My Subaru Forester for example had the P0420 catalytic converter code. This made it lock out the cruise control and traction control. Bells and whistles. The more there are, the more to break.

[@alphaomega5721]

About 25 years ago when training as a Bosch techie, heard a story about a Nissan that came in with a problem. This was the early 90s so fuel injection and engine management were still new. Car apparently had an issue when towing a trailer. At certain speeds the car started losing power as if the throttle was being held back. With no trailer it was 100%. And with trailer, it was speed dependant, and not gear dependant (I.e. not engine rev related). To make matters more interesting it turned out to be one specific trailer, as other trailers towed fine. After a little investigation it was discovered that the trailer hitch was for a 2inch ball, but the tow ball on the nissan was 50mm. At certain speeds the .8mm difference was enough for the trailer to oscillate at high enough frequencies on the ball to send a false frequency through the chassis and mounts to the knock sensor.....

[@PineHollowAutoDiagnostics]

@@alphaomega5721 that is truly crazy! 😳

[@kerrylewis2581]

This is a life lesson for troubleshooting. It's hard to imagine the car was parked for almost a year for an hour's worth of work. GREAT VIDEO!

[@petepeabody8905]

It shows transmission shops don't always know enough to care or research the issues. Isn't google cool sometimes. It was also sweet that someone was willing to share their problem and eventual solution. The customer must have been ecstatic. Great job Ivan and for not limiting your options.....Pete

[@knocksensor3203]

They (shops) just want easy repairs and quick money…

[@donaldlee6760]

@@knocksensor3203 - that makes sense. This simple repair was only 0.5 hours according to the Ivan's online book. Why should a shop fix a customer's car and only make 0.5 hours when they make easy money fixing transmissions? (thank gawd there are shops like Ivan's that have integrity)

[@billlangdon5914]

I don't have all data but Google is amazing. That is if Ivan hasn't already solved my problem before. Glad to see think tool back in operation.

[@thomasmartin2950]

I have said this for MANY YEARS, Fix what you know is broken. As usual, well done!

[@luigigonzalez5062]

The sad part is that the guy at autozone could have fixed this car at the parking lot, just to throwing parts and no really knowing how to properly do a diagnostic. Great job Ivan 👍

[@volvo09]

Haha, exactly! The magic codes would have fixed it.

[@tacocin]

That connector being previously disconnected means somebody was so close but yet so far. Being able to ohm out the sensor made all the difference.

[@hawkstone7254]

I guess they figured that if they removed it from the circuit, it couldn't cause a problem..... 😉

[@dragonwalker4644]

Guy probably got pulled off of the job before he finished the diagnostic ...

[@kenk3102]

...geez...who would'a thunk it....a knock sensor causing the transmission to go into limp mode....Ivan, your diagnostic skills continue to amaze me....this was a very enjoyable and informative video....thanks for posting... 🙂

[@tuberNunya]

You too can google.

[@seanbyers1973]

It is a good idea to check the alternator first. My 2005 Mazda 6 went into limp mode a few years ago and it turned out that the alternator was bad. I had the alternator replaced with one from O'Reilly's and it fixed the issue for about a month--until the car went into limp mode again. The alternator ended up still being the culprit. The problem is that at places like O'Reilly's or AutoZone sometimes the remanufactured alternators are not rebuilt properly. I learned that it is a good idea to have alternators and car batteries always bench tested at the store before buying them to spare yourself from future headaches. Hopefully this tip will help someone.

[@PineHollowAutoDiagnostics]

Get a Denso alternator from Rockauto, problem solved. Other aftermarket brands and sometimes even dealer remans are JUNK out of the box 😅

[@koloy999]

when it showed the knock sensor code I thought the engine is in limp mode for sure the 3rd gear on the dash thru the customer for a loop for sure and probably made him go the wrong route with the trans shop. thanks for all the good videos

[@randallgoldapp9510]

I've learned that lesson the hard way working in maintenance in a factory. Don't leave any obvious faults behind you, even if they don't seem related. They will sink you every time.

[@russellhltn1396]

I've done the same. But I'd like to know what made these things related.

[@randallgoldapp9510]

@@russellhltn1396 I would say a connection with the software. The ecm sensed a problem and disabled the transmission. Don't know why it didn't set set a transmission code. I guess you should just figure that out from the knock sensor fault.

[@russellhltn1396]

@@randallgoldapp9510 It didn't set a transmission code because there was nothing wrong with it. What's missing is a note that should be in the service manual that indicates this is a limp mode caused by engine issues. I'm not sure how much freedom the makers have for creating custom error codes.

[@randallgoldapp9510]

@@russellhltn1396 The main point is don't ignore an obvious fault just because it doesn't seem related. This is a common trouble shooting mistake I see a lot. It really isn't important why they are related, it is that they are related that's important. don't worry about why, clear the fault and move on.

[@larryjohnston52]

Does it have hydraulic fluid? Is that Hydraulic Fluid? 😂 "I think so." Always ask the "Stupid Questions"

[@Mr-Mag00]

Wow the reverb on that exhaust would drive me nuts, Super diagnosis Ivan, fixed for a $70 part, plus Battery and your time of course. I have a feeling you just earned another customer!. Stay safe thank you for the time you put into the videos. The more content the more answers solved and the world gains all this knowledge.

[@toriforrest9349]

THANK YOU FOR FIXING MY CAR!!!! I missed it so much. The exhaust is a glass pack. It sat for so long and I missed it so much!! 😢

[@PineHollowAutoDiagnostics]

My pleasure Tori! Zoom zoom 😎👍

[@Ottonic6]

I'd drive 5 hrs for Ivan to fix my car. Unfortunately, I live in Oregon, and no Ivan or Eric O. in my territory.

[@hendriediepenbroek5344]

I dont understand why they didnt replace directly the knocksensor stupid garage

[@philjerome9795]

The owner is very lucky. A lot of transmission shops would have tried to sell him a full rebuild.

[@Josb_Bluebird2143]

Thank goodness they didn't go that route!

[@philjerome9795]

I have seen this personally. In one recent case, a local transmission shop put two dealer supplied transmissions into a Hyundai, and they still couldn't figure out why the transmission wasn't operating properly. They called in an outside trouble shooter, who within an hour, determined that the harness connection to the transmission had been compromised and needed to be replaced. The vehicle never needed a transmission in the first place.

[@peetky8645]

true

[@johnnybartlett-ke9wg]

Man oh man ,you are super, you can fix anything, I wish all shops had people like you,way to go

[@marthabrown386]

I'm Dan, Martha's my wife. Great diagnosis Ivan. Funny how complicated vehicles are today and how something you'd think would nothing to do with the problem would be the cause of the problem. Knock sensor/trans. problem, who'd have thunk it.

[@djwwautodiagnostics]

This in so many ways is absolutely ridiculous. Fair play Ivan for fixing it and getting to the bottom of this, but how in the name of God can a shop keep this car for 8 months and still not fix what is frankly under their nose with a bit of research that is available to everyone. Well done Ivan. Easy one for those of us in the know 😀

[@duaneb193]

Your comment about doing a search reveals something - too many people think that you need to be super technical when you are looking for either a part or to help diagnose a problem. Years ago you had to be pretty specific on how you phrased questions, but in our more modern times, you can type it in the same as you'd ask a friend, and often times you'll get some amazing results. We just encountered almost this exact issue with the AC in my RV as it failed, and trying to find a simple expansion valve on the RV sites was a nightmare. Typed in a simple search for RV AC expansion valve and discovered that the local Advance Auto had almost the same exact valve as what I had been looking for days for using more technical terms. In a nutshell, type in your search using the KISS principal and see what it does - it might shock you!!

[@MattyEngland]

Just be careful when searching for a Big Block Chevy 😂

[@faxmen09]

Mazda 6 Wagon....unicorn. Google search to the rescue of a limp mode Mazda. ~10 ago not knowing better about going OEM, installed a BWD/Intermotor (div SMP) camshaft position TDC sensor form Advance on Civic, Still working like a champ. I think they make decent parts (sensors at least) for Asian vehicles. This one time, scan code alone was spot on solving trans limp mode issue. Who'd a thunk it. I'm sure owner happy to have his unicorn back in action. Nice job Ivan.....again. 👍

[@ghost37666]

8:12 "I guess anything is possible" is the ultimate wisdom in this field and every other field. I remember I was diagnosing a car that had shift problems, maybe even had the same symptoms, and the code that was set in TCM was a) unheard of b) had no information about it on the internet c) there were codes stored in the PCM that has no relation whatsoever with the transmission or how should it shift. After almost 3 days of trying to figure out the problem it turns out that one of the codes in the PCM that was caused by a MAP sensor that lost a ground wire causing the transmission to go in some sort of limp mode and make hard to shift gears, exactly like this car with different sensor and error causing the problem. The car was a Renault, a french car and I will NEVER forget this car ever.

[@CaballeroSantos0206]

Great thing to see how these things work That actually happened with my 05 Toyota Sienna, it was not releasing OD just because of a faulty KS. Thanks Ivan for helping people with honesty.

[@wadet73]

Thank you Chrysler for making it easy to read codes on 96 and and newer vehicles. Cycle ignition key 3 times on and off and on the 3rd time, leaving it in the ON position, the dtc codes pop up on the odometer. That's how i keep my my 20+ year old Durango and Dakota running and my previous 4 Grand Cherokees.

[@abdul-kabiralegbe5660]

This is like an extreme version of what happens to Toyotas (and maybe other manufacturers): when the knock sensor code prevents engagement for some gears. I've seen a Nissan (1st gen Xterra V6) have consistent misfires (flashing MIL) under medium to high loads while in motion (i.e. Drive) simply because of a bad knock sensor. The misfire didn't happen when revving the engine in Park or Neutral. P.S: Bless Mazda for that knock sensor location on this V6. Most other OEMs hide them in the valley.

[@marlu6373]

my 97 nissan quest was chewing knock sensors like there is no tomorrow.i think it was the bad position they chose to mount it.

[@abdul-kabiralegbe5660]

@@marlu6373 The knock sensor in the Xterra I referred to failed due to corrosion from the cast Iron engine block and a slow leakage from the corroded metal coolant pipe alongside it right at the bottom of the V6 engine valley.

[@AnnaWaipa-bq7dd]

Great job as usual!

[@abdul-kabiralegbe5660]

@@AnnaWaipa-bq7dd Thanks, but "as usual"? I don't quite understand.

[@dezzadiggler3693]

Another great diagnosis! By the way, the colourful material on the top of the dashboard at 4.59 was probably what the owner was thinking when the car went into limp-mode....just a thought....!

[@dougkubash8673]

One of our 2003 S-10's would intermittently want to start out in 3rd gear. I noticed the alternator making noise and the scope showed problems with the rectifier bridge. Replaced the alternator and the transmission never acted up again! Great video!

[@KBLIZZ333]

I seriously wish I could shadow you for a few weeks and watch you work. Its extremely impressive the way your brain works through some of these issues. Hell, i'd glady work for free the entire time. I legit have 26 years experience as a paid professional automotive tech but i couldn't hold a candle to what you do and am pretty envious of the level you're at in this field. Definitely one of my idols. No bs. And I don't have too many. Staten Island Keith is one. Mr Danner is another. Mr and Mrs O, Perkins, Brin Klein, Cody, Super Mario. Cuba, Mech Mindset. Steckler, Pete Meier, Jerry Truglia, Mike Becker, Bernie Thompson, and plenty more but its late and my brains slowing down so I apologize for leaving a few out. What I'd give to be a fly on the wall.

[@randy1ization]

its not just Ivans gift of mechanical and electrical skills., its his control of emotions.. he doesnt seem to get angry or aggravated by most problems. he is able to clear the clutter from previous attempts. and focus. most techs experience alot of pressure and fear because you are against the clock. he is very even keel emotionally. has a positive attitude and is very determined to find the root problem.

[@dans_Learning_Curve]

Yes! All that was said is very true! He's worked on old motorcycles bringing them back to life. He's spent time in Russia where thinking outside the box was definitely required. Not sure how long. Keith (New level auto diagnostics) took him under his wing for a week or so. I believe he's an EE that was working on his masters and got tired of the 9-5 drag and went out on his own. Ivan, did I miss anything or something needing correcting?

[@rj.parker]

I am not sure shadowing him would help. He is a trained engineer who knows how to be analytical. Using all available tools including scopes, pressure transducers and the best scanners. He has built up large amounts of experience by taking the harder diagnostic specialty route and no employees rather than the common and repetitive shop track. His wife is a professional which no doubt allowed him time to build his strengths before he became as proficient as he is today. And the small things. The use of a notebook to record steps and measurements. Knowing how to use search terms effectively by guessing terms likely to be in the answer. Occasionally phone a friend. Finally he was smart enough to visit youtubers like Eric O and listen when Eric encouraged him to do youtube. Now Ivan's youtube income may surpass his customer income.

[@randy1ization]

@@dans_Learning_Curve its also genetics.. his father was a nuclear scientist.. the apple usually doesnt fall far from the tree. Teaching people when they are young how to do deductive reasoning, utilize thier resources, and look at challenges as an interesting project rather then grueling work carries thru the adult life of the person. Ivan always says "this should be a fun case study". he has a different attitude. than your average Joe and is not so prideful that he is ashamed to ask for help at times.. he is smart enough to know that he doesnt know everything.

[@dickdelete]

Just shadow him by viewing his videos is already great 👍

[@lynskyrd]

I HATE transmission shops. NEVER had a good experience with them. I learned though- when my 76 GranTorino's tranny quit- I went to the junk yard and got one for $100 (back in 79) - took me and my buddy a week to do the swap- worked perfect. Learned a ton. Had to rent a transmission jack- but that thing was amazing. Anyway- Ivan, you are amazing. I hope that customer didn't pay those other guys anything. A whole year down because nobody wanted to THINK... other than Ivan of course. What baffles me, why NOT replace the knock sensor?? The code came up on the scanner- the part is south of $100 and it's pretty much in front of your face after you remove the BAD battery. Even if it's a "no way it's the knock sensor" thing- you've eliminated a 'possible'. Again Ivan- just awesome. I'd DEFINITELY travel 3 hours to have Ivan look at a problem.

[@paceauto5382]

Nothing like when they throw the parts cannon at it⁉️💯😂😂😂

[@tracydiller9378]

I work for Fisher Auto Parts here in Michigan and yes we try to get the parts out the door in 4. Great video Ivan as always nice fix.

[@willemstreutgers1154]

Lesson of the day is ; Mazda engeneers build in a safety feature if knock sensor fails or noticed an abnormalty, the drive train should go into limp mode. Anyway excellent find Ivan.

[@eurbanautotech]

Nice job! This video reminds me of one ScannerDanner did of an Audi that had no power. It had a code for a faulty electronically controlled engine mount that everyone ignored thinking that couldn't possibly be the problem... But it was setting the engine into limp mode without any indication it was being derated. Btw, the slamming into gear is normal. When transmissions go into limp mode they default to maximum line pressure. This causes VERY aggressive gear shifts. These transmissions are some of the most uncomfortable for that. Good job at keeping an open mind!

[@raymondwright2660]

Super stuff, really enjoyed that. All of these videos just reinforce my view that manufacturers have made cars so complex they are almost unfixable making them technologically obsolete so we need to buy another one when anything goes wrong. Heard hundreds of tales of cars and bikes taken in to dealerships charging top rates and unable to fix them.

[@AP9311]

Wow, well, all the trouble codes can be interrelated to everything. Damn knock sensor knocking out the transmission! Damn good fix Ivan! Great job fixing an hour of diagnosis! Wow unreal. I can't believe it lol

[@imagseer]

That gives us all hope! Check that everything else is working right before entering the wrong rabbit hole and lining up the parts cannon.

[@Kro_man_tx]

Watching you cover so many topics, I have learned to look at everything going on with a car. AND visual inspection! My daughter's car had a blower motor issue and all my research led to a wiring problem near the fuse box. But, performing a visual inspection on the wiring in the circuit, the resistor had gotten so hot, two of the wires had melted together shorting the circuit. A new pigtail connector and it's fixed! The resistor was fried, that was the original cause of the problem.

[@fredautos]

Great Insight, You Video has impacted a whole lot to me

[@mikescofield7887]

I love watching Ivan. I can't wait to get home every night after work to see if he has a new video out.

[@GregoryGlessnerViolin]

I like when he drops vids in the morning. Very pleasant way to start the day.

[@luckyguy600]

Why is that? Because he does what 90% of the rest of the world doesn't do. THINK!

[@luckyguy600]

Nothing I hate more than 'stupid people' They grate on my nerves! And that is generally how the world is going.

[@ritchieschofield1185]

This comfirms that in auto diagnostics, every day is a school day. No matter how experienced you are. Great job . Look forward to the next one!

[@theblackhand6485]

Scandalous! All of it. Except the 15 min. repair and placing a new battery. Well done!

[@Napert]

9:38 extremly lucky that the person asking that question actually followed up with how they fixed it instead of generic "nvm i fixed it" or "idk what happened but it fixed itself"

[@LesReeves]

When you said it had a knock sensor code I was betting that was it as you have said in the past on newer vehicles anything can cause all sorts of problems to show up on the CAN BUS HIGH/LOW.I bet the customer was pissed .Cheers another good video.

[@WeeShoeyDugless]

A few years back my W140 S-Class Mercedes would jump out of cruise control on the motorway, ABS light would come on and power reduced..... FIX.... a new brake light switch on the brake peddle. Go figure. So you are right, fix what is broken on modern cars, the faults may all be interlinked. Good troubleshoot👍🏻👍🏻

[@boblynch7348]

Another amazing story with a happy ending. Thanks, Ivan!

[@BABA-ws5eo]

I can see how someone can decide that the knock sensor is not related to the trans issue. It doesn't make much sense really. Great job. thanks!!!

[@williamburdon6993]

There are actually some really smart ingenious people out there, and luckily most of them are willing to share.

[@blkshk1]

You r a rare real gifted mechanic. Thank God for your gift!

[@peterdatechmen5506]

isnt the simplest fix often the correct one. Just cant fix what you don't understand how it works. Great work! That is how my apprentices are taught to think.

[@MalcDavison]

Made me smile Ivan.....You said "as good as new" and the head lining was flapping around like a main sail on an ocean going yacht lol.....Great video again matey....Saludos desde Esaña mi amigo....

[@АлексейДовженко-ю5ъ]

Sometimes, to diagnose a malfunction, just say OK Google 😎 Thank you Ivan! This car will be like new! If you do not take into account the sagging ceiling 😁

[@ThisIS_Insane]

That is a killer outcome! Sometimes, it's OK to trust what's in your face. While it is true you never know when for sure, but, your instincts are sharp and your nose for little hints and a fine tuned GUT FEELING, serve you extremely well! Stick a fork in that car, it's DONE! Congrats, Ivan! Keep on making it look sickeningly easy! 👏👏👏👍👍👌

[@ericaleshire1356]

Toyotas had an issue similar to this. If knock sensor faults were set on the 3.3L v6 engine, the transmission would shift through all gears fine the first time but would not shift into overdrive or 4th gear afterwards. Would need to shut the car off and restart it. Replace the knock sensor and sub harness, shifting would return to normal.

[@damiadedapo5363]

I faced similar in a 2013 Toyota Venza... Knock sensor codes and transmission goes gaga... However not exactly in limp mode, but give a violent jolt between 2 and 3. Nice job as always

[@inothome]

I bet your neighbors were all impressed by that exhaust!!! 😆

[@zippythechicken]

I hate people that do that.. its a fricken station wagon its not a race car

[@caseyjames9570]

@@zippythechicken why not both? ¯\_(ツ)_/¯

[@PineHollowAutoDiagnostics]

This one was whisper quiet compared to that yellow straight piped VW GTI 🤣

[@zippythechicken]

@@caseyjames9570 no its not a chevy nomad ... your mom gave you her station wagon so you would get out of the basement.. its not a race car HA!

[@2nickles647]

@@zippythechicken ...You mean when people either straight pipe their rice beaters or add a fart can to make it sound louder and cooler.

[@Brad-tq2pi]

Yup! K.I.S.S rule first… just a little farther info. Knock sensor was retarding the timing to prevent engine damage. Also putting trans in limp mode (which we know lol) 3 gear is most likely a 1:1 ratio. So putting as little strain on the trans too. That’s also why reverse worked. Direct drive (input and output shafts locked together) inside the transmission. Just turning in opposite direction. Good video!

[@PineHollowAutoDiagnostics]

But starting out in 3rd gear shreds the poor torque converter...not to mention the super violent shifts into R or D LOL!

[@montestu5502]

Amazing no one did the parts cannon and replaced the knock sensor and fixed this prior to you. Incredible.

[@hondanation9375]

I got to admit I wouldn’t have thought it would have been a knock sensor good video

[@wallebo]

Always such great content. I would have never thought that these two things were interrelated. They were so lucky to bring it to you.

[@SirDeanosity]

The PCM firmware was programmed to put the TCM into limp mode with a knock sensor fault. Likely the best approach is to have not codes ever. If one pops up then whatever change in the vehicle behavior occurs is related to the code.

[@wallebo]

@@SirDeanosity Yes. Thanks for the information. Always glad to learn. There are some smart people out there. I am not necessarily one of them so I am still driving my 1989Honda CRX HF that I bought new in Jan. 1989. It has over 377,000 miles on the odometer and has never been in the shop. The simplicity of the car matches my skill level perfectly. I don't have any power windows or seats, no airbags, no traction control, lane assist, power mirrors, automatic transmission, cruise control, infotainment system or anything else. I don't even have a cupholder. It was, and is still, basic transportation that has never broken down on me once and I have kept it that way with just preventative maintenance. Not one drop of oil has even hit the ground. It still blows 40 degrees through the center vent with the air conditioner on which is a godsend here in the deep south. It is a trusted piece of history to me and will never be for sale. I love the PHAD channel for Ivan's great diagnostics and how often he is able to fix something with no parts required and his sincerity and honesty. Have a great day.

[@dtnel]

I diagnosed a no comm for tcm, missing certain gear, sticking. Bought the car, Mazda 5 , 2008 van, 147k miles from owner for $750. Ordered a refurbished tcm from California. They were plug and play. DONT mount it on the transmission, rather on the firewall with a couple zip straps. The heat from the transmission causes this issue. The transmission would slam, hit into 3rd as well. Replaced tcm, cleared codes and has worked great since this last year.

[@ThriftyToolShed]

Crazy how the knock sensor can cause the transmission to go into Limp mode. Great detective work and fix!

[@allant2742]

Just WOW! Who would have thought it. Unplugged too. Top job Ivan. 🙈👍

[@victornicholson9859]

I had a 2002 VW beetle. It was throwing ABS error codes. Car under warranty. The dealership replaced ABS sensors 2 or 3 times. It was 20 miles round trip to the dealer. Driving me nuts. I called VW customer service, gee the multi-pin connector from the engine compartment to get wiring through firewall, had been sprayed inside with insulating foam only meant to keep water out of the inside of the car. Factory error created a short for the ABS system. It is nice to see that we have dedicated techs that can actually diagnose a problem. VW bought the car back from me under the California Lemon Law.

[@Thee_Dr_Evil]

had an 06 6s (v6) and it was a love hate, Loved driving the car, comfortable, good torque. Hated the front seal and valve cover (replaced) oil leaks and most of all the garbage aisin 6 speed transmission. in 140K the engine never gave me any real issues, but I did have 3 replacement transmissions under warranty. Trans would flair between shifts with at full operating temps. On the highway, peddle down it would buck between gears felt like the powertrain was going to fall out. Glad Mazda is wholly owned again, love my 17 Mazda 6, no a lick of trouble.

[@mmichaeldonavon]

Ivan, another job completed. As I'm concerned about your safety, did I see you do that "test drive" without your seat belt on? We need you Ivan. :-) A loyal follower, mike

[@michaelslee4336]

I’m an Aussie and grew up with belts, they are just built into our brains from kids. It really does hurt my brain to see so many Americans on so many platforms simply not putting them on.

[@billziegmond4943]

BRAVO Like you said fixed what's broke. You also revealed big secret on internet searches. KEYWORDS people. I work in I.T. and shade tree work on cars. (Hey a computer is a computer) Doesn't matter if it is on your desk or in a car they function is the same. Specific keywords like Ivan showed will often give you the answer you are looking for.. Nice job my friend.

[@edchenal821]

Good problem solving. Thank you. We had an oil pressure sending unit failure send a 2019 Honda Pilot into limp in mode.

[@Alanthe918mobilemechanic]

Great job as usual had the same issue on a 94 dodge ram 1500 bad battery customer sold me truck for 400 dollars I put a new battery in it and detailed (oil change, air filter, wiper blades) 4500 dollars sold

[@jamesnall569]

Wow, what a fun little wagon. I’m going junk my M3 Hatchback/station wagon when the transmission fails soon and I’m going to find an M6 Hatchback/station wagon to replace it.

[@mikeaho4143]

What a crazy diagnosis. What was the transmission shop folks thinking ! Not transmission related but it fixed the issue. Thanks for sharing !!

[@craiggoodwin9704]

Ivan, I think all that car needed was a nice day. Great to see you enjoying the weather while doing what you do. Makes us all feel good! Thanks for Sharing!

[@dougowens2686]

Crazy I have a 2007 mini cooper with a CVT car went in to limp mode due to a tach having and intermittent com problem , I noticed the tach blink before the limp/EP mode , Found one post on a forum contacted the guy to confirm we had the same issue i disconnected the tach and drove car with no issues I spent weeks tracing wires and checking modules Great job

[@brianw8963]

Watched this before leaving for work this morning. I told Gloria it was the knock sensor as soon as You said it had that code! How did I get so good? (Lucky for once) There is nothing wrong with a quickly once in a while! 👍👍🇺🇸🇺🇸

[@nbrowser]

Ivan, future reference herre with Mazdas like this one that have Ford engines....and yes this is a Ford V6. If you want OEM parts, call the local Ford dealer. I don't know how many times I've had to contact our local Ford dealer to get parts that Mazda says "we don't have that".

[@dogsplantscarsneatstuff176]

That's helpful! Are some of the 4 cylinder engines also made by ford in Mazdas?

[@gsudarshan7251]

I remember Ivan's video with the mazda rebadged ford escape where one subframe bolt was a FoMoCo part and had to be sought from a ford dealer

[@robertfarrar9411]

That was awesome! I never would have thought it would limp the transmission.

[@roxanneabbott8424]

Wow thinking outside the box, that is your forte Ivan! Cool beans!!

[@michaelslee4336]

Somehow get onto that original guy/gal and you thank them profusely. One time I searched you tube on how to reset the oil change reminder on my car. I found a 6 year old vid and said thanks heaps in the comments and the vid poster was very happy that he could still be if help that many years later. This tranny vid is from 2011.

[@vincentshelpfulhints4085]

People are worried about throwing parts at a car if there is a serious issue I can understand that. Not sure what that part cost. I would had that replaced if it were under 100 dollars with labor or if I could had done it myself.. Great Video and Excellent job.. I am waiting for Vehicles to go into limp mode for a low tire

[@shawnbelford3433]

Love your thought process. Great job Ivan!

[@frankf2485]

I agree with you about the availability of information on the internet being helpful, but I have also seen a couple of negatives. I have been a technician for over 30 years and have trained several techs over the years. I have seen young guys who would rather try to find their answers with a Google search than actually learn how to diagnose a problem.

[@fieldsofomagh]

Sister's Peugeot had abs problems. The fuel filter was replaced and voila, abs no more. The cause of course was quantum entanglement. Knock,knock my transmission is not working. The knock sensor is faulty. No head scratching there. Great fix after a year on the sidelines.

[@dongningprc]

Thanks, man! Great info! It's really entertaining watching your videos, and the stunningly rich rich source of information, just AMAZING!

[@paulsch973]

Wow I have had some problems cross between models but never something quite this crazy! Thank you for the video and info!

[@justsumguy2u]

This one didn't surprise me at all---anything that puts the car into limp-home mode can impact other systems. Parts required, but not expensive ones = win

[@localresident996]

Same thing on an 03 Taurus. Stuck in 3rd gear. 2 transmission shops said it needed new transmission. 3 egr codes and 3 transmission codes. Found that egr and transmission shared same circuit and wires were melted on egr pipe. New fuse and a quick wiring repair and the car was fixed after 1 year of sitting.

[@patriel1]

Wow unbelievable. You sir have excellent logic skills!

[@michaelweatherhead9470]

Thanks for the video Ivan great job 👍❤️❤️ it. My Subaru outback had a Abs code and O2 bank 1 and Temp sensor. Fixed the Abs code and all good.😅. Take care of yourself and family and be Blessed ❤️❤️❤️.

[@robpeabo509]

Great pickup Ivan! Mazda should really issue a TSB or some sort of instruction to alert mechanics (including their own) of this issue that can cause the transmission to go into Limp/Safe mode. It is way out of left field that a knock sensor would cause this transmission issue!.

[@2nickles647]

Ivan. Logically. If the engine indeed had a slight knock. Would it make sense to try to save the engine and transmission. That's why the transmission was in limp mode? Because I've had customers had a noticable knock and they were revving the engine even more 😂 Saying o...it's been like that I'm just driving it till it gets worse. Duh

[@thedreadedgman]

Really this shows that DATA is important... if manufacturers listed the CONDITIONS that can TRIGGER a limp mode... then you can just look it up but no they all have to be secretive about their damn software then years later they just act like they never made the car and no-one can see the data it's all so stupid

[@DonaldWells-wk8dc]

Stupid f*ks...take names.

[@Jeffo2024]

Thank you very much. My neighbors car had the EXACT same problem. Just ordered the sensor. Wish me luck.

[@PineHollowAutoDiagnostics]

Nice! Should be back on the road in no time 😎👌

[@windward2818]

What did we learn? There is a software bug most likely in the transmission controller. The PCM will broadcast the P0328 fault to the other powertrain modules on the bus. Putting the transmission in limp home mode will not address engine detonation. The PCM will address a bad knock sensor by changing the spark advance to limit the chance of detonation. The only strategy that I know of that could cause a system wide reaction to a bad knock sensor is if the PCM strategy used active knock. Which is a way to enter a knock condition given a set of engine drive cycle parameters to test the system and other things like fuel octane estimate. However, when a knock sensor is bad or the connector disconnected, active knock should be disabled. Perhaps there is a software update for the TCM? For a transmission in limp home mode for an extended time, I would do a fluid and filter change. Perhaps not a complete transmission flush unless the fluid looks and smells bad. So, at minimum, just the fluid in the pan and the filter. But, be warned dropping the pan may not be easy and in doing so you may require a new pan gasket. However, by inspecting the pan and any debris you can get a feel for if the transmission has been abused by limp home mode. Perhaps the transmission shop already changed the fluid and the filter? If you do a test drive after limp home mode and you feel a TCC shudder or an overdrive shift shudder, then replace the fluid and filter. If you are doing a complete flush you could try using a synthetic blend transmission fluid from Mobil 1 which I have found has a slightly higher viscosity than most factory fluid which helps eliminate shudder if you do a complete flush (change).

[@adamcweber]

I have fixed countless transmissions in limp mode but have never heard of this one before. Must be a secret known only to certain Mazda Techs and engineers. Can't believe there are no factory diagnostics for this or a pairing code set in the TCM. Hopefully Ivan you post this tech tip in Alldata.

[@flatdaddio]

Very cool! I would love to see the program logic on how the transmission goes into limp mode because of a knock sensor. They must have had a reason. lol

[@techguydilan]

On Japanese cars, the transmission is always getting a "torque signal" from the PCM/ECM, so it can "prep" for shift's. It's one of their secrets for smooth shifting and reliability I feel. lol The bad knock sensor meant that the PCM couldn't properly calculate the torque signal, as it didn't know the knock condition (which would definitely throw the actual torque off of the signal, if the engine was knocking and the PCM couldn't tell) so it was likely shutting off the torque signal. It wasn't until 2010 or so when the OEM's thought to have the no torque signal condition actually trigger a readable code from the TCM. So as you said at the end of the video, always fix codes in other modules before chasing specific rabbit holes.

[@techguydilan]

Also reminds me of an issue I saw when I was in college. Had a UPS (battery backup) in our lab which would not communicate with any of the computers in our lab via serial port/RS-232. Since I was one of the better students and had all my assignments caught up, the professor put me on the job as classes for the prior two years could not figure it out either. So, I noticed since they had us wipe the lab computers so often, they were just using drivers built into Windows XP. So I just started updating drivers one at a time and trying the communication, starting with anything that *could* influence the serial port. Nothing there. So moved on to every other driver. As soon as I installed the video card driver, it started communicating. On the next lab computer, I installed just the application for the UPS and the video card driver, and it worked on that too. TL;DR: I once had a video card driver influence how a computer communicated to a battery backup via an old serial port (like USB before USB was a thing.)

[@GeorgeKennedy-u4r]

Had a friend with a Nissan Titan that got stuck outside my house when it wouldn't shift out of park. I thought it had one of those fancy electronic shift mechanisms but it turned out to be a broken shift lever bushing under the dash. We fixed it with a plastic wire tie and it lasted at least until the truck was sold 4 years later.

[@davyarthurs]

Well done Ivan. As I always say: the answer is out there, you just need to find it - power of the internet.

[@DS-ss396]

That's the way to think. Usually someone out in there has had the same problem. I research the same way. It's all in how you use those key words.

[@mailpup]

I'm a DIYer and I ran into a similar problem with a friend's 2001 Toyota Highlander with the 3.0L 1MZ-FE engine. It would set a knock sensor code (I forget the number) whenever she would accelerate onto a freeway. Then it would go into limp mode but if I cleared the code, it would be ok until she went onto the freeway again. I replaced the knock sensors (there were 2 under the intake manifold) and short wire harness and problem solved. While in there I also replaced plugs and valley coolant bypass hose, just because.

[@mlsargent51]

YES! Absolutely the gas issue! way too many times you get 1 with no fuel, and the gas light on solid.

[@xelercheddar8026]

This is how i fix 90% of the cars i work on seriously, its not hard do your research use your options, otherwise great work again ivan!

[@yelyab1]

Cross talk in the clock circuit! Back feed through an active, modulated short to ground. I’m makin this stuff up as I go along.