PSA Micro Dagger Trigger Upgrade Options, Tips and Tricks - Glock 43x, Glock 48

[@At3tactical]

AT3 Tactical Available @ Amazon amzn.to/46ot4am New Monthly Giveaways & AT3 Tactical Videos (No Firearms Sales) content.at3tactical.com/

[@timrobinson6573]

Yes. I replaced all of the Micro Dagger frame parts with Glock 43x/48 parts except the locking block and takedown lever. Way better trigger feel.

[@At3tactical]

We found that to work well also 👍

[@abundancebase19]

You should post it on your channel

[@tenormdness]

Johnny Glock 4311 trigger is the best I’ve tried. And I’ve tried a few just playing around with them. It’s not cheap, but it’s a different setup with all new components. I absolutely love it.

[@At3tactical]

Good recommendation.

[@michaelsherfield3749]

I had my gunsmith install the ghost edge 3.0 in my micro. It felt great, but after 2 magazines it didn't want to reset and would occasionally fire instead of resetting. I will return the connector. If I don't have anymore problems I'll change the trigger to that axiom.

[@Budget_operator]

Could you review the tactical pontoon trigger for the micro dagger?

[@michaelsherfield3749]

I bought a 3.0 ghost connector and a 43x trigger housing. I will eventually change the trigger but I don't have that big of an issue with my hinged trigger. Probably because I've never had a flat faced trigger. I will have my gunsmith do it for me that way he can smooth everything out. And do it right I don't trust myself.

[@SnappyKid17]

Can you make a vid for the Ghost precision G43X Trigger, and the Johnny Glock G43X full trigger system and shoe upgrade? I would really love to see the difference comparing the 2 in this video to the two I just mentioned.

[@At3tactical]

Thanks for the suggestion.

[@NobodyAwsum]

I preferred combo rn is oem ikternals with the overwatch precision polydat. It took the soft 4.5lb gen5 trigger feel to 11. It now has close to a 6lb very crisp wall, but if you pull clean through you basically dont notice it, and for me thats just another added layer of protection. My g19 build is a Grit Grips frame and its got like a 2.8-3.2 lb trigger depending on how i pull and where, and i love it but i can hand this to my small framed friends and teach them without the worry if accidentally having the trigger pulled, which i cannot do in my edc g19 build, and i don't like the "let the recoil surprise you" kinda triggers as it teaches bad habits. You dont want to not flinch, you just want to control it and only do so to compensate for recoil.

[@At3tactical]

Good Info

[@michaelsherfield3749]

Just got the ghost 3.5 and the oem glock trigger housing hopefully it works well

[@At3tactical]

Nice

[@michaelsherfield3749]

@@At3tactical I have a question will the 3.0 connector be lighter than the 3.5? And will it fix my reset? Thats my biggest complaint. Also will I need to change the housing to change it out? I will be having a gunsmith do the work for me for less than $30

[@michaelsherfield3749]

@@At3tacticaland thanks for the video. That axiom is too light! I'm getting it 😂

[@TheSkeptic000]

I can get two daggers for one “real Glock”. I will still need to change out the trigger on the Glock bc Glock triggers suck.

[@michaelsherfield3749]

@@TheSkeptic000 people really talk down on psa. A bunch of kids that don't know what they are talking about. I asked a guy what his problem with psa was and he tried to say quality control and lack of customer service. 😂 I had to send my micro back was fixed and returned in 2 weeks with a video of it being test fired with a list of all part replaced. I still have dannys the lead pistol repair guys personal number. And will get a response if I ask him any questions. Amazing company!

[@brianleabo6295]

How about going over the upgrade of the magazine? Did you go for the bigger magazines for that 13 Ruth 15 round magazine

[@At3tactical]

We did a short video on magazines kzbin.info/www/bejne/l6HNnmSOac-EhKM .

[@AnDy.Strong]

Crazy how the weight dropped 50% without changing springs

[@tylerrussell3388]

So you need to upgrade the trigger housing for the ghost trigger bar or no? Shows you put it on the stock micro dagger one. I ordered one of those from you guys and it most certainly does not work in my gun.

[@At3tactical]

Sorry to hear that. The Ghost Trigger Bar worked just fine in the stock Micro Dagger housing for us.

[@michaelsherfield3749]

Did you get it figured out? I was about to order one. Too broke at the moment to get the axiom trigger. I have more of a problem with the reset than the actual trigger pull weight travel

[@tylerrussell3388]

@@michaelsherfield3749 I did not no. Mine has a completely dead trigger with this trigger bar installed. No function whatsoever and I’ve got it installed correctly not sure what the deal is I tried returning it but AT3 apparently doesn’t respond to emails for customer support so I’m stuck with it. I did notice the top piece near the sear it’s a little wider than stock maybe I’ll shave it down and see if it’ll work I’ve got 7 other guns I can carry. I don’t think the trigger is that bad the regular dagger trigger I have no issues with and don’t mind it one bit but if I could get close to 3.4-4lbs I’d be happier lol. And same not about to throw a new trigger into it the frame and C1 slide with a TLR7 sub was enough alone.

[@E52O4]

@@tylerrussell3388 Try looking at the gap between the connector and the trigger module. It should have some separation from the trigger block, but not excessive. Mine came from PSA too close to the trigger block. I removed the connector, and bent it gently until it showed a slight gap (about a note card thick gap). Took it to the range today, expending 180 rounds (Blazer and Tula steel case). Only one FTE, but might have been me limp wristing the pistol. Other than that, no issues will trigger reset of a dead trigger. Good luck diagnosing the problem.

[@pabloantonioaguilar5371]

Also had this exact issue. Dropped the pin in, dead trigger. Put the stock one back in and works

[@michaelsherfield3749]

I have a question if someone could help me out. Is the 2.6 lb trigger too light for a edc? I mean you would have to pull the trigger for it to go off right? I've never pulled the trigger on my 5.5 lb trigger by mistake. It will still be drop safe correct? I've been told that's too light for a edc but I feel the lighter the better.

[@E52O4]

It is a bit light for EDC. I like mine to be 4-5 lbs. All of my pistols are about 4-5.5 lb weight triggers.

[@michaelsherfield3749]

@@E52O4 thats decent. the trigger pull isn't that bad. But my reset is way too long. Maybe I should just change the connector.

[@ParrishT3]

@@michaelsherfield3749 The Ghost connector would be your best bet. It just makes the wall easier to get through so you still have that little bit of trigger creep on it before getting to the wall. Alternatively, you could just get a trigger shoe instead of replacing the entire thing, just take the hinged trigger off and replace it with a regular trigger and get a better feeling one.

[@claytongross5657]

I need more of these videos for other guns, and they need to be longer. Do you have any trigger replacement ideas for a Taurus G3 or maybe a Beretta 92 clone by girsan? I'm a whore for gun knowledge 😊

[@timrobinson6573]

And for cheap guns.

[@At3tactical]

Thanks for the feedback. More videos coming soon.

[@At3tactical]

@@timrobinson6573 We will do our best

[@andreww9513]

@@At3tactical Seconding the request for more budget-oriented content as well! I love the red dot I got from y'all on my shotgun.

[@tylerrussell3388]

Why? The G3 and G3c have an awesome stock trigger for what they are. Shoot a bunch of other guns and you’ll change you mind on that decision. Plus, a trigger is more than what you’ll pay for the entire gun lol.

[@angelr6614]

What red dot is on the gun?

[@At3tactical]

Good catch, that is our ARO Mini Micro Red Dot, it will be coming to market in the next few months.

[@tylerrussell3388]

Can I give you a piece of personal advice and my opinion? Take the AT3 logo off of them, it makes it look more like chinesum cheap looking just my honest opinion. I do buy a lot of stuff from you guys so don’t hate lol

[@At3tactical]

@@tylerrussell3388 We appreciate the feedback.

[@nicksmith6758]

i COULD NOT get the that trigger kit to fit in my dagger (compact size). the trigger was hitting my trigger guard on the bottom. Anyone else have this issue?

[@At3tactical]

Sorry to hear that. This video was only showing how to install a trigger on a Micro Dagger not the Compact Dagger. In Glock terms the Micro Dagger is a clone of the Glock 43X and the Compact Dagger is a clone of the Glock 19.

[@reiniergarcia]

It’s not even worth getting a “dagger” in the first place😂😂. Just get a real Glock.

[@MF-Rell]

Tell everyone else what to do with their money. 😂

[@michaelsherfield3749]

I like my micro "dagger" and "dagger" compact. It would be 1k+ easily for a glock with a gold fluted barrel slide cuts and optic ready. Built mine for 350. Hasn't failed me yet 500 rounds thru it.

[@ParrishT3]

You can buy a fully kitted out Dagger for the same price as an OEM glock that has terrible pull and plastic sights. The Dagger uses metal sights on it and is way more rugged. The only people who cry about the dagger are the ones coping they spent way too much on a Glock.