How does PLC read data of load cell transmitter

[@ATOcom]

In the video, the data read by the PLC is constantly changing because of interference. Solving this problem can be avoided by adding shielded wires or grounding the shell.

[@rttr4869]

Is it possible with Siemens Logo?

[@ATOcom]

@@rttr4869 yes.

[@rttr4869]

@@ATOcom ok thanks

[@scotthosey3450]

Ok, but if I was going to add a valve with a fast fill and slow fill how would I control all that with the scale?

[@marcosantuario7777]

Nice video. Do you have a similar video but using a cubic liters valve?

[@georgealbo]

thanks for this video can you make a series of videos for omron PLC Ladder daigram

[@SandyPrawira-p3i]

Is it possible to connect any type of load cell directly to the plc analog module and get the reading from the load cell?

[@ATOcom]

not directly, you need a tranmitter for load cell signal to standard signal as 4-20mA, 0~5V or 0~10V.....

[@ianwong3987]

If I selected 0-10V output by accident and need 0-5V is there a way to divide voltage in half through calibration after receiving the product?

[@ATOcom]

The output can be adjusted to 0~5V in the normal calibration manner.

[@muneebkhan7266]

Great work ❤

[@automationwork5904]

nice

[@ATOcom]

: )

[@Iceoatice]

plc.fx3u-24mr can do it ?

[@ajitsingh-wx4tm]

Sr i have omron cp1e plc and mad42 analog module but i am unable to select the module how to select module in cx programmer Please help me sr I am waiting for your reply

[@ATOcom]

You can get relevant information through the Omron hardware unit manual (W479).

[@allagomar6033]

Great job thank you

[@taufiqrahman6332]

excuse me sir, can i use arduino to read weight from transmitter?, i was trying and the signal is not displaying as i expected.

[@ATOcom]

1. If your Arduino can only read digital signals, what you need is a transmitter that outputs digital signals (RS485). 2. To read digital signals, information needs to be exchanged through a communication protocol, so direct reading is also not advisable. 3. If your Arduino can directly read standard analog signals (0~10V, 4~20mA...), then you can display the weight data correctly. 4. After you read the transmitter data, the display data may need to be converted (such as hexadecimal to binary or decimal).

[@taufiqrahman6332]

@@ATOcom thank you for your reply. i will try it

[@oyousafali1859]

@@taufiqrahman6332AoA Did you got the transmitter connected to arduino. Pls reply, i am facing the same problem.

[@RajeshYadav-be7ds]

Boss Can you please make complete video on weight and plc hmi

[@umargul5644]

Great 👍

[@josefranciscovalentim2300]

great !! I was waiting for this video thank you very much greetings :: valentine

[@ATOcom]

: )

[@josefranciscovalentim2300]

Good Morning you could help me with a weight indicator reading by communicating with clp omron through serial port 232 how to convert the strings into real numbers since already thankful valentine

[@ATOcom]

You can store the obtained data in a register area, and then use the PLC to monitor and view the data in real time. You can convert and display it to decimal in the PLC viewer. Or use some device to read the data in this storage area and display it, this device can be HMI...or other

[@josefranciscovalentim2300]

@@ATOcom ok thanks God bless you

[@reginaldreed9759]

I wish it wasn't so blurry

[@trungnguyen-es9yx]

CovidImages need to be invested more than half19

[@muneebkhan7266]

Great work ❤