AU falcon auto to manual conversion wiring adjustments using original wiring and ECU

[@michaelbyrnes7944]

With my xh Utes I was lucky they both are factory manuals both running AU intechs with the proper gearbox looms

[@harvs597]

So to sum it all up very simply, You solder the black and red+bluestripe together You cut and add blue plugs to the reverse wires You add resistors to the red+green and purple+red to tell transmission it is in neutral You add resistors to the temp. wires Is this all correct, I have limited understanding of electrical parts and am struggling to piece it together. Thanks.

[@harvs597]

Do reverse lights work with this?

[@stevedotcom4598]

Thankyou very much for the video. I still have a higher idle in neutral. Did these instructions cover that and I have missed it? If so which step have a likely got wrong? Is it the "range" change when the resisters are added between the Red/Green stripe and Purple/Red stripe wires?

[@khobistringer4272]

What if you don't have cruise control? Do I just not worry about it?

[@markmoreton9099]

Do you actually need the resistors?

[@easytalker864]

Great video!! 👍

[@billspooner3792]

Gday mate just wondering will this progress an resistors be the same for a el auto loom to run a manual gearbox?? Im having issues with my xg ute conversion using the auto ecu with revs hanging an un an down in revs at idel an after driving the revs hangs an creeps up to 2000 1500 rmps hope that's makes sence

[@AUXRRoadstoration]

Hi mate great video I was able to do mine first go and correct. Thank you. I am stuck on the cruise control component, are you able to do a bit of a video on that section. Thanks for the information you help everyone with.

[@akaitv6606]

You need to integrate the factory switch on clutch pedal back to the cruise module , so that when you push the clutch pedal , cruise is disengaged , you can manually turn off cruise anyway before changing gear, if unsure how to wire it .It's connected to brake pedal aswell so when you push the brakes on cruise disengages .

[@lachlanshaw2447]

How do you get the speedo working?

[@akaitv6606]

Speedo is separate In the harness manual and auto is the same

[@anguse5910]

Anyone know if this is the same for EL EF Falcon

[@billspooner3792]

I just asked the same thing in more detail lol besides mine is a xg ute I put complete el wiring an engine in

[@akaitv6606]

EF and EL is the same transmission, should be the same all I would do differently is run a dual throw toggle switch N on one side and D on the other to combat the idle issue .

[@soch_society9396]

How many wots are the resistor

[@akaitv6606]

1/2 watt will be finec

[@shamuscurtis5336]

Do you have to do the temperature one for it to start or do thermo fans just stay on?

[@akaitv6606]

Prevent it from going into limp home mode

[@jaymcintyre5687]

does it really need a resistor

[@pingapete666]

@@jaymcintyre5687 i done 2 never used resistors and never had one go into limp mode either

[@adrianioan8265]

Hi mate i hava an iveco daily i take of the automatic gearbox amd i fit manual but now don't start u no why thx

[@akaitv6606]

Neural safety switch usually

[@adrianioan8265]

@@akaitv6606 hi mate i remap the ecu i put a manual map inside but still dont start you know why thank you

[@mattfernandez6379]

I'm about to do a conversion, I have a manual xr8 ECU, will this work without cutting wires as per your video or have you done this to trick the auto ECU

[@akaitv6606]

Get the loom for the manual . Jimmy only does it using auto ECU and manual gear box .

[@ryanvanzyl9352]

Hey mate do you know how to do the wiring on ba manual conversion

[@akaitv6606]

Haven't touched a ba however the trans are similar to AU with a slightly different pinout.

[@emmetpoppy]

What switch needs to go in for the cruise control mod? And which wires from the auto loom go to the manual box speed sensor? Great vid btw 👍

[@akaitv6606]

You need to add a switch on clutch pedal ,

[@Ricky-vd5sq]

Hey mate do you know what wires they are on a Fg mk1?

[@akaitv6606]

He deals in AU's only

[@draedelchau6765]

Can I use the same resistors as you or are all transmissions different? Cheers

[@akaitv6606]

Different

[@draedelchau6765]

@@akaitv6606 so like we're do I test the residence for the trans what wire do I put my multi metre to

[@perrymierisch154]

I don't care about the cruise control revving up can I just leave it and turn it off myself or will it cause grief I only use It on long roads