Audi A4 B6 | Mini H1 HID Bi-xenon Projector Retrofit kit Installation instructions headlight upgrade

With this retroquick kit you transform your headlights to full Bi-xenon headlight, with xenon low beam and quad high beam (xenon + halogen). You will have more light in front of your A4, and next to that your Audi will look better with the luxurious look of xenon with the beautiful bright white light.
𝗬𝗼𝘂 𝗰𝗮𝗻 𝗯𝘂𝘆 𝘁𝗵𝗶𝘀 𝗴𝗿𝗲𝗮𝘁 𝘂𝗽𝗴𝗿𝗮𝗱𝗲 𝗸𝗶𝘁 𝗵𝗲𝗿𝗲:
retrofitlab.com/products/audi...
𝗜𝗻𝘀𝘁𝗿𝘂𝗰𝘁𝗶𝗼𝗻𝘀:
0:08 Remove the H7 bulb
0:18 Remove the headlight frame clip. First remove the side closest to the engine, this is the shortest hook and is easier to remove.
0:25 Remove the 3 nuts (5,5mm) which hold the projector.
0:30 Take the Valeo H7 halogen projector out of the housing.
0:40 mount the retroquick braket to the projector.
1:15 Place the projector.
1:23 Guid the high beam solenoid wire to the high beam section.
1:35 Mount the projector using the nuts. Note: since the thread is thin, don't tighten them too much, you can break the thread!
1:47 Connect the high beam splitter to the connector, bulb and solenoid wires
2:06 Put the headlight frame clip back in to place.
2:13 Mount the bulb in the Mini H1 projector with the clip. Connect the ballast power cables to the H7 connector. To guide the wires through the cap, drill a hole of 22mm in the cap.
2:30 Here you can perfectly mount the ballast using double sided tape
2:43 The Valeo H7 halogen compared to the Mini H1 Bi-xenon
𝗔𝗱𝘃𝗮𝗻𝘁𝗮𝗴𝗲𝘀 𝗼𝗳 𝗮 𝗕𝗶-𝘅𝗲𝗻𝗼𝗻 𝗽𝗿𝗼𝗷𝗲𝗰𝘁𝗼𝗿 𝗿𝗲𝘁𝗿𝗼𝗳𝗶𝘁 𝗸𝗶𝘁:
• Much better light output
• Double high beam (xenon + halogen)
• No glare
• Lower energy consumption (35 watt instead of 55 watt)
• Luxury OEM look
𝗖𝗵𝗲𝗰𝗸 𝗼𝘂𝘁 𝗼𝘂𝗿 𝗻𝗲𝘄 𝗙𝗮𝗰𝗲𝗯𝗼𝗼𝗸 𝗴𝗿𝗼𝘂𝗽:
/ europeanheadlightcommu...
𝗙𝗶𝗻𝗱 𝘂𝘀 𝗼𝗻:
Facebook: / retrofitlab
Messenger: www.m.me/Retrofitlab/
Instagram: / retrofitlab.com_official
Our website: www.retrofitlab.com/
𝗢𝘂𝗿 𝗦𝘁𝗼𝗿𝘆:
Retrofitting refers to the addition of new technology or features to older systems. These days there are a lot of people who put a simple plug & play xenon kit in their halogen headlight housing in an attempt to improve night vision and looks of their vehicle. In fact they don’t realize that their headlight beams are often worse than before. Night vision achieves relatively little improvement on night vision because of a poor beam pattern, which increases the blinding of other road users. This is because their headlight housings are designed for halogen and not xenon.
A true Bi-Xenon projector update is now possible for your car. Such an upgrade will significantly improve your light output from 700-2100 lumens to 2800 and 3500 lumens, without blinding other traffic with glare from your headlight. Upgrade your headlight OEM style!
The latest high power Led bulbs will upgrade both the exterior and interior lighting system of your car. Led lighting is becoming more and more popular in the automotive market for obvious reasons. They have longer lifetime, use less energy and improve safety with their fast response time.
Do you have any questions? Do not hesitate to contact us, we are happy to help you out!
Good luck with your retrofit!
These products are not ECE-approved and must not be used on public roads in any exterior application. Use on public roads will invalidate both the operating license and insurance coverage.
#Audi #A4B6 #AudiA4B6 #Aharon #Retrofit #DIY #Upgrade #Headlight #lighting #HID
#Retrofit #LED #custom #improvement

[@texfromro]

The main beam on the b6 is just awesome. you only need a good pair of H7 halogen bulbs to make the full of it.

[@geert2991]

I've got this kit installed and it works Great thnx Wouter

[@Utubeash7]

That's probably the fastest retrofit job ever....nice work though. I am struggling with my 2007 Camry SE for a while now. I am going with the Mini D2S projectors, 35W ballast and 35w 5000K Morimoto bulbs. wish me luck.

[@josejimenezjuarezjuarez1361]

Perfect but I'm still waiting when you do this myself but a sport clio 182👍

[@RolandFeyenoord]

Great. I'm curious to see it

[@davidj7823]

what's the best way to get the light centered. my lense is almost touching top of the housing and has a gap on the bottom.

[@TechIsFashion]

I don't if it's standard but I realize that these projector in that housing are cross side. The left projector cutoff is on right side after 4 feet.

[@TechIsFashion]

(sorry it was late). I said that I have the same housing and I just don't know why the projectors are not at 90 degrees. It seems like the left projector is pointing on the right and the right one points on left. It actually decrease the width of the output.

[@benic8571]

I have a question . My 2003 a4 is non HID . But I bought some ecode headlights . Could I use any HID kit on those or not ? I cant fit any of my bulbs in the new headlights I bought also.

[@precious0047]

Can you please help me I'm unsure home to order I clicked the link on this KZbin page then pressed buy now but it tells me to feel out that thing witch I don't know how to I want the crystal white one witch ones is that ???

[@paulomiranda337]

thank you

[@ep09043]

Thanks for the reply ;)

[@logmegadeth72]

Thanks for the great video. I have the same bixenon projectors. Now, my high beams are pointed very low but the low beam is aimed properly. I believe I may have tightened the bottom two nuts for the projector too tightly. Did your original projector have thick rubber washers that went on the two bottom studs? How many turns did you do on the two bottom nuts? Let me know. Thanks.

[@logmegadeth72]

+Retrofitlab do you happen to remember how much you tightened the bottom nuts? I am using the original white rubber pieces.

[@ep09043]

Hello.. Why the upper projector shines differently from the bottom? The European version is different from the top.

[@Silentdogs]

hi do you need warning cancelers for a 2003 audi a4?

[@uchashavliashvili7057]

dear hello i want to change front turn signal lights with leds on audi a4 b6 2002.can you help me to choose a which led bulbs shoud i buy

[@paulomiranda337]

Good afternoon, could you tell me where you buy this kit for my! thank you

[@fatonal7971]

Good job

[@michalsmisko4403]

hello i have d1s xenon original bulbs, is it problem?

[@sdimais]

Hi guys, Can I use the Hella's original mount from my Audi S3 2003 to hold the new projector as seems you did for this A4 B6?! Or should I build one mount from scratch ? Thanks!

[@diegoms30]

Is there any way to keep with my stock valeo ballasts and d1s bulbs?

[@Bakanelli]

Im wondering the same 6years later 🤣 how did it go?

[@robertoilijanic]

on 0.40 you fit adapter for audi...can you sell only that adapter?i allready have your lesn bu i dont have that adapte

[@ao8398]

+Retrofitlab hi, does mini h1 comes with adapter mountings for the projectors?

[@Zsido94]

what do u have used? 3" projector or just 2.5"?

[@Zsido94]

Retrofitlab thanks for the answer

[@djrio123]

Nice...Are You Telling Me That I Have To Go With The Same Procedure To Install H.I.D.S On My A4 B6 Too?

[@keloduma]

Pretty much since it's a sealed beam

[@laurentiupopa5001]

I have an A4 B6 with xenon, and I would like to fit the S4 B6 bixenon kit. The lens is 3" instead of 2.5", can I find a lens shroud (bezel or ornament, whatever it's called) and replace it? If I remove the glass of the headlight, can I replace the shroud with the larger one for the 3" lens?

[@Bakanelli]

What did you do at the end?

[@laurentiupopa5001]

@@Bakanelli nothing, I sold the car since then. I cannot give you any solution

[@djrio123]

Please Let Me Know...Thanks.

[@cyclingromanias2917]

Hello, can I change the 2.5 Inch With the 3 inch mini h1 on an audi A4 B6?

[@Retrofitlab]

No, this will not fit the bracket..

[@RolandFeyenoord]

Zitten deze in je eigen Audi?

[@nemorider6280]

Hi! If I already have xenon headlights, to switch to bi xenon I only need the lenses, right? Will work with oem balast?

[@Retrofitlab]

Yes, you only need the lenses and brackets etc, which are already included in the kit. You can continue to use your existing ballast. But we have upgrade kits for single xenon and bi-xenon, you need to know which xenon you have.

[@csanad1993]

hello. i just removed the projector. but under the projector it's 2 little plastic. one little and one bigger. And i dont know where to put the small and where to put the bigger one. can you help me?

[@csanad1993]

Retrofitlab there is 2 little nylon spacers. i have removed the projector and when i reinstalled the high beam and the main beam is dipped. the main beam lights to the sky and the high beam on the ground. can you help me please. I don't know how to solve this probleme...

[@csanad1993]

Retrofitlab thank you bro! i will try. have a nice day

[@andreiprimu]

Would you onlu sell the retroquick braket? i already got the Projector lenses but i need the braket.

[@Retrofitlab]

Yes, we do; www.retrofitlab.com/en/bracket-1.html

[@reklam34]

Hello my car audi a4 2004 s line .. my problem its the light it's very bad even i change the new d1s but still same problem what should i do or change hepl pls ??

[@padrebodybuilder817]

Projectors...

[@Lolo-cx3mx]

Hello, would this kit fit in an Allroad C5 housing without major modifications? Thanks

[@Lolo-cx3mx]

Retrofitlab Thank you, I will email to you to get more info.

[@wojtasek595]

Hello. I am have AUDI A4 B6 2003year Bi Xenon . What have light bulb D2S or D1S ?

[@kevinhawley962]

compare to honda lights damn audi way over engineered headlights xD still love my a4 b6 1.8t thou

[@Juthrbog]

But is this retrofits legal in Europe? I'm afraid I won't be able to get my car approved for driving when extending my road license. What is the procedure?

[@Juthrbog]

Thanks a lot! Looking forward to purchasing your product!