Audi DL501 / S-Tronic *Adaptation/Calibration*

[@muhammadazlan7449]

It is the same term between ‘basic setting’ and ‘calibration’??

[@BewarHassan-cq1rr]

Do you know how to fix this code Torque Restriction due to Clutch Temperature

[@filipdopirak5226]

Hi Svarog Performance I have same transmission but my is stucked in error P287B00, i tried several diagnostic tool to reset but it is still stucked. Can you give me some hint on this problem Thank you

[@yogamon]

Is there a way to tell by the dl501 adaptation values if it is wearing at a high rate? Like the zf 6 speed could tell you how far from stock they have moved to adapt to aging.

[@clbeob]

Do you recommend to do adaptation reset values after changing transmission oil on Audi S4 ZF 6spd automatic ?

[@Svarogperformance]

Yes you can do that

[@clbeob]

@@Svarogperformance which values should I change and by how much ?! 😊 thanks!

[@clbeob]

@@Svarogperformance A4 *

[@clbeob]

@@Svarogperformance can I adapt the transmission just by driving in some way? Thanks

[@tomekdrab7971]

Hello, I have a question whether you did the adaptation in the 0CK gearbox

[@stephan1986]

Thank you! Now is my DL501 much better. (Basic settings + Adaption via vcds)

[@kaisonsamson3480]

i realize I'm kind of randomly asking but do anybody know a good website to watch new tv shows online?

[@sonnyroy1363]

@Kaison Samson flixportal

[@kaisonsamson3480]

@Sonny Roy thank you, I went there and it seems to work :D I really appreciate it !

[@sonnyroy1363]

@Kaison Samson glad I could help :D

[@mortezagachkar6366]

Hi I'm trying this adaptation each time saying Stop for shafty reason

[@oskarpyc1632]

Will this work with a tiptronic (torque converter) gearbox? I have an Audi A5 3.0 tdi tiptronic and wanting to reset the gearbox adaptations

[@dawidwojcicki8697]

Hello. Do you now code for seccur Access for 02 adaptapion transmition??

[@doganarslan6571]

Great video. After adaptation how to drive the in D or manual

[@mortezagachkar6366]

When try to do adaption on vcds coms up aborted for shafty reason

[@MrDevelishBoy]

Is it same procedure for CVT/Multitronic gearbox?

[@Svarogperformance]

Sorry Not sure about that ! Never work on ZF

[@LBB988]

when install after market clutches, should do these steps?

[@Svarogperformance]

Absolutely yes ! You have to do actually first time when heat cycle at the first start on new clutch after 1 hour then drive the car 100 miles do it again / than drive car for 500 miles do it again / then launch the car 5 times and do it adaptation again and after this, perform others at every oil change to be just make sure it’s all good

[@thomasthompson6231]

Where can I purchase this software and what hardware to connect to vehicle do I need?

[@predragbogunovic5151]

VCDS software is free but you have to buy the adapter cable as it acts as a key to allow you to use the software. you have to order cable from Rosstech website. there are two options, the cheaper is about $500 and allow you to use VCDS on up to 3 cars and the full version allows you to use it on unlimited number of cars but costs like $1500-2000

[@umair87able]

Is This method can be used on Volkswagen Golf mk7 7 Speed DSG ?

[@predragbogunovic5151]

VCDS works on all VW cars including other brands that are owned by VW such as audi, porsche, bentley, skoda etc.

[@adist.3627]

Hey Bud, I'm doing the mechatronics repair kit, which is just the wiring harness. Do i need to do this adaptation after? I think I need to do adaptation when changing the solenoids but not the repair kit harness? Also, will doing this delete my TCU tune? thx

[@Svarogperformance]

Yes and mechanical or software repair / changes I recommend perform adaptation and correction

[@adist.3627]

@@Svarogperformance is the car on while doing this or just ignition ? Thx

[@Svarogperformance]

@@adist.3627 car must be running and hot ! Transmission oil temp should be at list 60-70c

[@ricardomendes7116]

Where to buy the kit in a reliable seller?

[@adminaspx]

I did a scan and got the following codes: P176B00 passive/sporadic P17D600 passive/sporadic P17D700 passive/sporadic P286B00 active/static

[@langweilig2355]

P286B Clutch contact pressure too high. P17D7 Electric pressure actuator 5 Monitoring circuitry - Electricity too high P17D6 Electric pressure actuator 4 Monitoring circuitry - Electricity too high Greetings from Germany 🇩🇪

[@Imabaitr6]

Hi! I have 2009 Audi S4 (0B5 DL501) after i replacement the clutch plates and mechatronic repair kit, I have big slam and jerky when i take R or D while i standing. I do adaptation but i dont take test drive beacuse i dont know is it normal to jerk or no. I just need to go 100-200 kilometer and it will be good? Thank you!

[@Svarogperformance]

Transmission Shouldn't do that, try adaptation one more time

[@Imabaitr6]

@@Svarogperformance i made adaptation 4-5 times but the problem is the same :/

[@Imabaitr6]

@@Svarogperformance maybe I need to do this with original ODIS?

[@Svarogperformance]

@@Imabaitr6 You can try but sounds like you have some hardware issues with the pressure control could be a bad Solinoid or board etc.. Would recommend doing a full rebuild and cleanecharronic unit

[@Imabaitr6]

@@Svarogperformance before this there was no such problem, only the clutch slipped, so I renewed it...:/

[@moealfaily1662]

How much did it cost to install the upgraded clutches? At what point do you think they need to be upgraded as far as the power at different stages (using apr as the example)

[@Svarogperformance]

Labor around $2K+ If you having issue and clutch slips then yes I would recommend do performance clutches but OEM Clutch Pack should be good for 550WTQ

[@jabarrylewis5718]

Svarog Performance where you get the upgrade clutch to buy?

[@NAs034]

No need to upgrade the clutch packs unless going bigger blower.

[@stevenreyes3094]

My OBD11 won’t let me says I need security access login. Would you happen to have the code?

[@mortezagachkar6366]

If you can help thanks

[@drancyneuftrois3120]

Do you have any idea why the Clutch valve calibration gets aborted due safety reasons??

[@Svarogperformance]

There is lots of stuff could be rated

[@joshoxley648]

An sometimes I find really got to be between 40-60 degrees c

[@drancyneuftrois3120]

@@joshoxley648 I tried many times on several temperatures but didnt work. Believe it has to do with my pirate vcds.

[@joshoxley648]

@@drancyneuftrois3120 I got Vcds, good for OAM’s but I prefer Autel has 5 steps all up compared to vcds 3 things to do, I do probably 1 a fortnight down here in Australia were we don’t get much access to TsB’s an genuine info, what’s ur car doing after work has been carried out? Leaving any codes ?

[@arkious]

@@drancyneuftrois3120 did you ever find out the reason for aborted safety reasons?

[@filaov]

Is the procedure the same for Audi A4 with STronic gearbox ? Thank you

[@Svarogperformance]

Hi, should be the same it might be a slightly different option for adaptation