Super Simple Bullet Hole Fix

[@philporter-ks6fv]

Hey Great method. I was just about to attempt metal to metal body filler on some screw holes. While shopping for body filler I discovered soldering technique and said "hell this is right up my alley from my electronics experience". Great to know it works on bullet holes being that I am located in Memphis, TN. I can't wait... Thank you for the content.

[@autobodytrainingsolutions838]

Glad to help

[@davidyoung3211]

Wanted to say thanks, great vid, bought a new f-150 fender bought it with with 9 holes for a wheel flare, my doesn't have flares, so filled them in with your method and was able to tape a peice of flat thin copper behind them, then filled the holes, was blown away how well this worked ,when finished the front was able to peel the tape and copper came off, witch made solder flat on the backside, love the turn out impressed thx, alot!!! 5 stars!

[@autobodytrainingsolutions838]

I’m glad it worked out for you. Thanks for watching

[@MrHotguy034]

This is great to know just in case I ever get shot at

[@autobodytrainingsolutions838]

Just remember to duck. Thanks for watching

[@wayne9518]

Cool trick. It's how I first did auto body. Then learned to braze, then learned to weld. Electronic solder is smaller so it melts easier and is usually acid free compared to plumbing solder

[@FarmsteadForge]

I think I have good neighbors 😂 but I do have an old farmhouse sink with a bullet hole that I'll have to try this on, thanks!

[@bradyoung5555]

Just coming across this video, do you think it would be strong enough to fill holes in an engine bay

[@amireftekhari6513]

Wow that situation with the neighbors exceeded very quickly

[@autobodytrainingsolutions838]

Yeah neighbors are funny that way. Thanks for watching

[@31shotsboy]

Would melting solder into an equal to hole sized bead, then directly soldering that onto the metal be an option also?

[@autobodytrainingsolutions838]

I don’t think so. You needed more solder than the size of the hole to be able to tin the metal and you’ll have some that will probably fall through the hole. Thanks for watching

[@shawnrussell375]

Would this work to fix cracks around a bolt hole from a mirror on a door? I'm using a different style mirror

[@autobodytrainingsolutions838]

Possibly but the cracks need to be opened up for the solder to flow in. This method doesn’t work if it’s a stress crack but if the new mirror puts stress on it it may crack again. Thanks for watching

[@tarmac245]

Could you use this method for larger patches?

[@autobodytrainingsolutions838]

It could be used for a slightly larger patch although for cosmetic use only. This patch doesn’t have a lot of strength so it shouldn’t be used in a structural area or where there could be some stress.

[@III6victor6III]

Exactly which model Weller is that? I’ve got a Hakko soldering iron, maxes out at around 800 degrees.. I can’t imaging my iron getting the sheet metal hot enough for the solder to stick as easily as your Weller did. I’ve got an antenna hole to fill and there’s glued on felt headliner on the other side. To repair it, I’ll need to minimize heat as much as possible. This might just be the way to go. Thanks for an awesome tip!

[@autobodytrainingsolutions838]

My soldering iron is a Weller D650 and heats up in about 10 seconds. Make sure you're using an acid core solder (which is typical plumbers solder). The metal needs to be perfectly clean for the solder to stick. You will also need to make sure the tip of your iron is clean; I usually use Scotch Brite. I've done antenna holes before too and haven't had any problems with this method. Here is a link to the soldering iron on Amazon that I use - amzn.to/2zf6bw1

[@AlexRodriguez-pg9xk]

Did you ever fill your antenna hole with this? How has it held up? I have one to fill also

[@bradbloes]

Thanks for making the video. My solder iron goes from 5-40watts and maxes out at 900 degrees Fahrenheit. Will this be hot enough if the area is prepped like shown in the video? Thank you

[@autobodytrainingsolutions838]

I’m not sure if that will work. Little confused on the watts of your gun. Try it on some scrap steel and see what happens. Thanks for watching

[@isyisy8142]

I have a truck that had a sun visor it was blown off and left the holes I don't plan on putting it back on, will this be ok to fix the holes?

[@autobodytrainingsolutions838]

It will work fine. For another option check out my video Hole Repair Without Welding. Thanks for watching

[@tonyharvey7188]

What would be the best way to do trim holes?

[@autobodytrainingsolutions838]

Trim holes can be solder closed easily sometimes without a patch. Depending on the size hole, they can be filled with solder but make sure the edges of the holes are clean and free of any paint. Thanks for watching

[@nob3na322]

Where you got those little metal patches? And will thise work on a old car panel? Like 70s c10

[@autobodytrainingsolutions838]

Complete Guide to Using Soldering Gun in Auto Body Repair kzbin.info/www/bejne/i5m5hH-eoN-fjdk Check out this video. I just make small patches from scrap sheet metal and it works on all cars, old and new except aluminum. Thanks for watching

[@nob3na322]

@@autobodytrainingsolutions838 amazing thanks a lot u saved my life!

[@stevedawson3863]

Just replace the fender??

[@autobodytrainingsolutions838]

Yep you can do that too but what if it’s the quarter panel? Thanks for checking it out

[@bwtjma183]

Thank you sir!

[@edwardl4866]

Would this be the same case for a puncture?

[@autobodytrainingsolutions838]

Yes it would. Thanks for watching

[@hackermd7275]

Is this the same wire used to solder electronics?

[@autobodytrainingsolutions838]

No this is plumber solder

[@AndriyMisuyrak]

@@autobodytrainingsolutions838 Is that a requierement to use Plumber Solder or any solder will do the job ?

[@autobodytrainingsolutions838]

@@AndriyMisuyrak plumbers solder works the best although there are several others that can work. I only use plumbers as it has a low melting point

[@jtonthatrack3984]

Yeah a few years ago when I got drunk, I shot my truck a few times and now it looks like i was running from the cartel or something 😭

[@Ghostzaku]

I bet your views on this video go up every new year

[@autobodytrainingsolutions838]

Best comment I’ve had in a long time. Thanks for watching

[@LOST2BAGHDAD]

Does this work on Aluminum panels?? Thanks

[@autobodytrainingsolutions838]

No, this only works on steel

[@stevenduering7155]

That damn kitchen gun

[@dd52161]

hey bro cool vid did u ever shot someone ??

[@Jayreganmusic]

Nice work, glad I don’t have neighbors that shoot my car.

[@grumps316]

Is there a certain gauge of sheet metal you recommend? What do b you use to cut the sheet metal? Just found a bullet hole in my truck probably from the idiots who use guns to celebrate the Superbowl. SMH.

[@autobodytrainingsolutions838]

Depending on manufacturers, gauge can vary. I just use whatever scrap I have laying around. 16 -20 gauge works good. I use tin snips to cut small patches. Thanks for watching

[@AlexRodriguez-pg9xk]

@@autobodytrainingsolutions838 any issues with temperature changes and the shrinkage/expansion? Especially in conjunction with filler/primer?

[@autobodytrainingsolutions838]

@@AlexRodriguez-pg9xk There shouldn’t be any issues with temperature changes. I’ve never seen a problem with any type of repair using bondo and primer as it will expand with the metal

[@Electricbrew]

Who is is from Portland Oregon watching this video

[@autobodytrainingsolutions838]

?

[@caelincoolz5814]

Is anybody else watching this not because they're going to patch up a bullet hole but for a different reason? Mine is Fanfiction.

[@autobodytrainingsolutions838]

This repair works for trim holes or any other small holes. Thanks for watching

[@majestybabybaby]

simple ?!!!!

[@ThatEsepe]

I just put a piece of duct tape over it

[@autobodytrainingsolutions838]

😂

[@NickDanger1957]

First thing first if someone shoots your car please contact you local police department then call your insurance company and get yourself a new fender

[@autobodytrainingsolutions838]

I did that but it happens every day

[@derekstratton9146]

Wow, never would’ve thunk to call the police until you said something. Appreciate you spreading your knowledge.

[@jimstern4244]

I don’t know where this guy lives but he should move ,,,,,,,,,, soon

[@autobodytrainingsolutions838]

It may be too late

[@615freeco4]

shot my fuckin floor yesterday

[@autobodytrainingsolutions838]

I hate it when that happens

[@divineg3796]

My door.