AUTOMATIC TRANSFER SWITCH 3phase Complete wiring

full practical wiring. step-by-step procedure on how to wire a 3-phase automatic changeover switch.
Please click the link below to watch the part 1
• AUTOMATIC TRANSFER SWITCH
• Complete wiring | Auto...
• AUTOMATIC TRANSFER SWI...
• THREE PHASE CHANGEOVER...
• #1 Contactors explaine...
• HOW TO WIRE AN 8PIN TI...
• HOW TO WIRE A TIMER TO...
• how to connect 3phase ...
• Forward and reverse mo...
• 3phase motor winding c...
• How to check for open ...
• HOW TO WIRE D.O.L STAR...
• STAR DELTA CONNECTION
• #1 Direct-on-line Well...

[@anthonyfindlay466]

Another very informative video, great job, keep it up bro👍

[@obloni_Electrical]

Thanks senior. 🤝

[@Simply2sureOdds]

Superb explaination 💯

[@Simply2sureOdds]

Please can you do a presentation on how to run a 3phase induction motor with single phase supply 🙏

[@danielteyehuago1633]

I'm here again. Thanks for sharing it with us

[@Ibrahimsaheed-bn2ph]

A well explanatory video keep it up boss

[@obloni_Electrical]

Thanks bro.

[@bonnylasu7665]

Sir I'm very interesting and learning more about your video teaching of electrical installation. Why not you putting auxiliary contact block on the 2 contactors?

[@MosesChanda-eh2of]

Please thank for the good teachings but I would like to learn about how to wire a complete hammer mill which is above 15hp and ATCS NOW IN SINGLE PHASE

[@emmanuelwilson-tq6lz]

sir please thank you very much for your teachings. but sir i would appreciate if you would help me with a video of an automatic change over as you have build with the contacts but including phase monitors, rely, and timer and how it works

[@obloni_Electrical]

Well noted.

[@OduroAsareJohnson-fn6nz]

Thanks

[@costheta2]

Bien joue

[@obloni_Electrical]

Merci beaucoup

[@ridwanahmed6477]

Wow 😮 So easy

[@obloni_Electrical]

Sure!

[@user-jl2db3gw9c]

thank you but I can see it well if you can explain the way you display with picture

[@obloni_Electrical]

Noted

[@noelfaithfulkari2857]

You can apply this same process to bigger load, like using assuming 200amp contactors with timer.

[@obloni_Electrical]

Sure 👍

[@noelfaithfulkari2857]

@@obloni_Electrical I saw a video on KZbin, I wasn't sure of his. He used 165A contactors, timer, pilot lights, cct breaker's, no schematics shown.

[@noelfaithfulkari2857]

Nice video, but I didn't see the schematics.

[@obloni_Electrical]

All the drawings are in the part 1 please use this link to watch. kzbin.info/www/bejne/iYW4hJd_qqqYrMUsi=W1mWw6fUXV4EVGHE

[@deedav4453]

Please do a video on a manual changeover

[@obloni_Electrical]

Well noted boss

[@obloni_Electrical]

Please check my video on "How to wire a three-phase and neutral changeover switch. Thanks

[@merkebwamanuel9540]

Hi sir i am very intereted. But on which point of the ats is we should connet the remot start wire that comes from the generator control module?

[@user-jx6sf8dx8q]

Please i need work im also electrian ❤

[@ahiagbleseth9500]

I think I need more explanation on this video?

[@obloni_Electrical]

Yes. You need to watch the part1. In the part one I did a thorough explanation on how the contactor works, how the interlock is done etc. You don't have to skip the part 1 please

[@user-nd6sf5ww9t]

Please sir where do you located

[@obloni_Electrical]

I'm in Accra, Ghana