Interesting. I never thought about it before. Always nice to learn something. Thanks for the video.
@TheDanny09012 жыл бұрын
Very nice info added to the knowledge of a beginner :D Thanks! Liked and subscribed!
@johnogola9036 Жыл бұрын
Thank you for this very informative video. What I need to know is IF breakout boxes like Godiag GT100 have the GPT cables in their MFCs because it seems some ECUs cannot be read in OBD mode on the bench. Thank you.
@Hayssam_Hallab Жыл бұрын
Thanks. Very usef
@train49052 жыл бұрын
Nice explanation,thanku
@crispenthunder97732 жыл бұрын
Interesting! thank you.
@sosscs Жыл бұрын
I have MEG17.9.12 ECU model, and already opened the ECU so I can clone the firmware. I have an Arduino Uno and a CAN module to use with the Arduino. I have the pinout for the ECU, the boot pin, the can-h and can-l, and the gpt0 and gpt1. Do I just provide analog signals to gpt0 and gpt1 and use boot mode, and then read through the CAN bus? or there're instructions I need to provide to the processor in the ECU which is "TC1762 Tricore Infineon" to then allow me to read the firmware?
@soemyataung233411 ай бұрын
Thanks alot
@ibrahimbayramoglu84022 жыл бұрын
hello, is my master sending the gpt signal over 0 5 or over the can line, is it enough to have only 5 volts connected?
@siwypfk12 жыл бұрын
Good one! Do u have AutoTuner too? If so, similar review as flex possible?
@Automotivesp2 жыл бұрын
no i dont have, and i dont like it v much to buy it..Soon making Flex full review.
@sosauto222 жыл бұрын
bonne continuation
@ibrahimbayramoglu84022 жыл бұрын
i have flex i have pcm flash i have autel j2534 i have pcm flash i use it in boot mode without any problems i didn't use benc mode pcmflahs benc is off I'm asking that's why we only need to connect 0 5 volts to gpt in benc mode
@mmfix38512 жыл бұрын
Is it possible to connect the any other ecu which the tool dont support but we know the pinouts and use same CPU ? Then to read and write the eeeprom ?
@nitexozo10 ай бұрын
no
@jany992 жыл бұрын
👍
@Bondangoed2 жыл бұрын
What is VP or VPP?
@Automotivesp2 жыл бұрын
positive voltage
@thesmartguy3523 Жыл бұрын
GPT is generally at crank/cam sensor connections, and in most ECUs crank and cam won't be on the same connector as power supply CONNECTOR
@nitexozo10 ай бұрын
i dont understand sense this comment....
@ibrahimbayramoglu84022 жыл бұрын
my master, gpt terminals on flex box 7 and 8 when i plug in another device on flex, which one is it?
@ibrahimbayramoglu84022 жыл бұрын
Does the interface send the gpt signal over 3 or 5 volts to the ecu?
@Automotivesp2 жыл бұрын
@@ibrahimbayramoglu8402 sends a square signal 0-5v depending on ecu
@ibrahimbayramoglu84022 жыл бұрын
@@Automotivesp thanks for the information you provided
@ibrahimbayramoglu84022 жыл бұрын
gpt 0 and gpt 1 should we give 0 5 volts in both cines?