What Can You Do With Excessive Play in Your Steering

[@morlando51]

On my ‘64 Falcon, I thought I would just go in and replace a couple bushings, that turned into adding a couple ball joints, that turned into replacing EVERYTHING on the steering and suspension. 🙄

[@tombryant1104]

Easiest way to grease box is remove one of the lower bolts and the fill plug. Then use a grease gun to fill from the lower bolt hole till starts to ooze from the fill plug. Easy pezy. To adjust, loosen lock nut and add half turn to adj screw. If it's still has play add a little more. Probably best to drive vehicle between adjustments.

[@mach1driver]

The go-to guy to to rebuild classic Ford steering boxes is Chockostang. He is often seen on the largest Mustang forum: Vintage Mustang Forum.

[@ShopOfTheseus]

Fantastic video. Rebuilt steering boxes are on back order for my truck so I may try this method.

[@jeffdriver3000]

An easier and cleaner way to grease it is you turn the steering wheel to full right turn then remove the vent cap and the farthest cap screw and use a grease gun to put the grease in the vent hole until it comes out the cap screw hole. Then turn the steering wheel to full lock the other direction and add more grease until it starts to come out the cap screw hole. Then you are done.

[@cameronjuzda7246]

Dont give up after watching this video check the large adjuster nut it fixed my problem on my vega box.

[@crosswits1]

Could you remove the cap and put a grease zero in the cap. To make greasing the steering box easier?

[@jtrain100179]

Bought a box for my 68 got it from a parts store. It worked great for about a year then I was right back to the play in the stering wheel but worse. My front end has had a complete rebuild.

[@terremolander5243]

Just looked at our steering gear box. I think we will be taking ours out and painting it. Do you have a recommendation for a Ford correct matching paint? Thanks for another video.

[@65Coasty]

Borgeson makes a box for the Falcon. Not cheap though.

[@johnbarker5009]

Those look pretty sweet, and you don't have to spin the wheel like Captain Jack Sparrow to turn the car anymore.

[@adamwnichols]

I have a 69 F100 with a power steering box. I was wondering if the power steering boxes needed to be greased like you demonstrated in this video? Thanks!!

[@AutoRestoMod]

This is going to sound cheeky but I would actually consult the service manual to see for sure. Or you can go out tofordification.com and see if that has been covered there.

[@adamwnichols]

@@AutoRestoMod thanks for the feedback!

[@leethomas9198]

Needs a rag joint and some wire?

[@PotteryGoddess]

If you do put an upgraded collapsible box in it, I would love to see that, since I have a 66 Ranchero with that same "Spear" column, and would love an upgrade.

[@stephenhotzjustdriveit]

Fun fun fun!

[@alicenfred]

How much play in box is excessive?

[@AutoRestoMod]

It's the one time in life I will say that 4 inches is excessive.

[@thomaslynch2083]

You can use a fish scale to check the box

[@fknows1]

why can't you just replace the upper ball joints, unless the inner bushes and pin are worn out as well, its a shame I'm so far away I'd have that box as good as new in no time for you, just needs a clean out and readjusting correctly, on the worm and sector shaft, doesn't need a new box

[@mycontinental3611]

What is the best way to adjust the adjustment screw.

[@fknows1]

@@mycontinental3611 remove top cover so you can see what is happening inside the steering box first, undo adjustment screw, (if you don't know the box condition) see if the worm shaft or worm drive has excessive movement or feels knochie, than reinstall top plate, with steering box in centre position, screw down adjustment screw until the box has correct free play and load.

[@alanwhite3280]

I have a Galaxies and found the removal, cleaning, inspection, reassemble, then using the shop manual make the Freeplay/ backlash adj. Then paint it.

[@alanwhite3280]

Ps works the best.

[@johnbarker5009]

Pretty sure if I tried that I'd end up with grease everywhere including the inside of the exhaust pipe and the underside of the dash pad.

[@rudykay5618]

Use channel locks

[@classics289]

You are as usual sooooo incorrect on this procedure. I have said this before on other videos of yours, do a little research before you make a video and act like you know what you are doing. The correct procedure is described by jeffdriver3000 in the comments.