Bambu P1s Mods are WORTH it !

[@NickBR57]

The P1S does NOT scan the QR code on the build plate - it has no scanner. For X1C just photograph the QR code on the existing plate, print onto a label and stick it in the right location (you can download and print a location guide for sticking on labels). For users with AMS risers the touch screen as shown will stop you being able to get the lid in easily by the looks of it, so about to investigate whether it supports alternative mountings (like replacing the P1S screen as the X1C uses the same location and doesn't interfere with the lid with an AMS riser). Throw away your purge lines

[@Optikification]

I use the Panda screen on my P1S, I have a lid riser and an AMS on top of it and the AMS as a riser to allow bigger spools and the panda does not block anything. My panda screen actually sits above the P1S screen as well.

[@milchpulverkakao4917]

@@Optikificationgood to know

[@girlwiththemostcake865]

I printed a simple desk stand. The thing is wireless no need to have it plugged in and mounted to the printer. Just print the stand, and plug a usb c to the back of the screen and you can charge it that way. When you unplug the USB C it works off its charged battery.

[@crankshaft007]

Great info about the unit not having a scanner for the plate

[@swdw973]

You can print mounts for the Panda Touch screen that allows it to slip over the top of the existing screen. No issue with getting to the lid easily when you have a riser

[@TMad_3D]

I did the light upgrade and wow! Such a huge difference and I love it. Thanks for the suggestion!

[@stefanxlindstrom]

About the Panda Lux, DO NOT use both lights at the same time. It will exceed the 0.3A recommended by BambuLabs. Bigtreetech has updated the installation instructions as well saying only to use one of the light strips.

[@TheRawketLawnchair]

this. unplug the original light.

[@bluewolf4915]

Was wondering about this.

[@venorando3672]

So what's the point? The original is more than bright enough.

[@stefanxlindstrom]

@@venorando3672 I disagree the original is way to dim.

[@TheRawketLawnchair]

@@venorando3672 nah, the original is dim.

[@joshhardin666]

I've seen a bunch of folks install the panda touch on their p1s, but I honestly don't get it.. what do you do with the front panel display beyond scrolling down to the connection code so you can connect your printer to your slicer (and maybe enable local only mode if that's your preference as it is for me). beyond getting the connection code, pretty much every interaction (short of turning off the annoying exhaust vent fan sometimes when i grab a print), I do all the interacting with my printer with the slicer app on my computer (in my case, i'm a big fan of orca slicer, but bambu slicer does the same thing). you could even use the bambu app on your phone if you want (I never do, but you could). it does bug me a little bit that there's no webui on the p1s by default so I can't just use my phone's web browser like I do on all my other printers), but it's fine. - all of the adjustments you mention with the panda touch, I can do right in orca slicer or bambu slicer.

[@drdoomslab]

From what ive seen and people ive asked the people who have one or want a panda touch generaly seem to have been 3d printing for a while and are just used to using a screen on the printer. they seem to even like writing to an SD card and putting that in the printer and then having it print by the SD card. I could see this screen being useful if you had a few printers and wanted a dedicated device to control and monitor all the prints but where not sat at a computer. But for me this still would be an extremely limited usage case. Much like you i just use the Orca interface to control the printers. I just wish the cam was better or we could upgrade it. It works fine just want more rez and esp FPS.

[@briejensen5874]

Yeah, I don't get it either. It seems more like a "cool" upgrade than a needed upgrade. I've had my P1S for a while now and have hardly touched my screen as both the phone/computer are really all that is needed (after initial setup).

[@briejensen5874]

@@drdoomslab A camera upgrade would be awesome along with a LiDAR upgrade. Both of these come with the X1C but the price jump to that printer from the P1S seemed unnecessarily large.

[@tomaszkarwik6357]

The one thing i use my screen for, is when i finish a print right before falling asleep and want to dissable the light

[@joshhardin666]

@@tomaszkarwik6357 that's fair, but I can do that from desktop which is like 3 ft to the right of it *Shrug*

[@hayleyrekcah7982]

So honest question, am I the only one who uses a vacuum to clean at least the bottom of the printer regularly?

[@janslavik5284]

Nope, I do it with a small handheld vacuum too. Might need to print an adaptor for it though, getting into all the corners is a bit finicky.

[@9x29Dillon]

Nope. Even printed some smaller nozzles to help clean it out.

[@danyo41]

I keep a mini shop vac with the brush nozzle under my desk. It's a life saver for tiny supports that end up all over my desk/floor plus the scraps in the bottom of the printer. Also great for dust and cleaning my work station! Highly recommend

[@Serenityindailylife]

Nope, have a tiny shop vac with a 3d printed adapter. I have it run under and I use a brush to push it I to the funnel adapter.

[@吉田圭汰-t1v]

仲間がいた

[@willemoudewater3123]

Great video really enjoyed it. love to see more add ons or mods for the P1S, I have mine now for a couple of weeks and I'm absolutely in love with this amazing printer. I always owned XYZ printers and unfortunately they stopped making those so I bought this one as it was on Sale for the 2 year anniversary. Huge improvement of 3D printing.

[@turdferguson8412]

Got my P1S a couple months ago and have kept every poop line it's ever made. Not sure what I'm going to do with them but it's gonna be cool I can promise you that

[@ItsMeaDMaDe]

Ha. That’s awesome. I know I have started collecting them just to fill that holder.

[@DennisCrawfordJr]

@@turdferguson8412 there is a broom on makers world

[@DadsRCGaragePNW]

I bought my x1 for the exact reason of tired of messing with things. For build plates I’ll pay the extra to have the Bambu labs plates. Takes a step of making it work out of the puzzle.

[@AfraDuvall]

Thanks for sharing . I enjoyed your content thoroughly and look forward to more content in the future. I have one Bambu P1s and one FLSun S1, When I need to print complex multi-color models, I fire up my P1S. When I'm printing larger models like helmets, I usually use the S1. I absolutely love them .

[@kensik]

For the Panda Lux DO NOT PLUG IN BOTH LIGHT ON THE P1P AND P1S IT IS TO MUCH DRAW AND COULD BRUN OUT YOUR BOARD. there is a warning about this on the website

[@73FPV]

I love your edits. Thanks for the work you put in..

[@ItsMeaDMaDe]

Thanks 😊 I’m happy to do it.

[@Badkitty24]

I was going to buy the Panda Touch when i bought my P1S AMS 4 months ago. I never bought it and i never use my panel. I used it a few time to check how many print hours the machine has racked up. That's it. Otherwise i just use bambu studio to use and monitor it. So i saved some money.

[@Thumpernator1]

Instead of printing and using that "Beveled Inside Edge", just a strip of blue painters tape does the job better. Debris can't get under the tape like it can with the printed part.

[@pocketlint82]

Great idea. I think both the ramp with the tape over it may be the best of both worlds

[@Serenityindailylife]

I use both because the tape kept tearing.

[@RobSandstromDesigns]

Good information. Will need to look into the flex plate you discussed that has the good gripping capability.

[@swdw973]

BTW. its a Cryogrip, not Cryptogrip plate. Since this was made they've released 2 additional versions that are blue. One for PLA/PETG called the Frostbite, and another with finer textures called the Glacier. You can print PLA, PETG, TPU, ABS, PA and other engineering materials on the Glacier.

[@richardrussell1025]

Just did the Lux and Panda Touch, and after watching this video I gotta go get the double CryoGrip plate.

[@rickhudson7598]

Nice video, very helpful. Just wanted to comment, if you want a larger scrap bin, just design one. I'm no CAD expert, and have actually never used dedicated CAD software, but I can use Tinkercad, anyone can. It would be very simple to create a larger bin using it. Give it a try.

[@YaNeK92]

I was thinking the exact same thing the moment I saw them sticking out so much at the top. I would go as far as printing it longer so they can fit properly with a closing dust cover haha

[@ypehille]

i printed a holder witch puts the panda over the original controles. In case of emergency you can flip the control up to use the original

[@FATSNAIL-FPV]

That's actually useful info! Got a link?

[@kylebrake1806]

What a sick moustache

[@DadsRCGaragePNW]

To me modifications means no warranty where upgrades don’t usually void a warranty. Lol

[@akeygma]

Coolest thing about Double-CryoGrip plate is when its less stick, use clean cloth+water to wipe and it will refresh again. No soap!

[@ItsMeaDMaDe]

Nice haven’t had to clean it yet. I’m still loving the build plate it’s amazing.

[@mitchellbernstein42]

Can you use it with TPU, ABS, ASA & PC?

[@akeygma]

@@mitchellbernstein42 the plate I got says do not print TPU on it. I guess its too sticky and become an issue for TPU.

[@toddroles3234]

Do you use the crypto plate heated to normal bed temps? Website seems to say not to heat bed?

[@akeygma]

@@toddroles3234 I heated the plate same as PEI texture plate to 55C. The customer support suggest to print with 35C but I didn't bother to change the temperature. Check with your customer support because I heard they improve their process from time to time so experience may change.

[@roberthutcheson2329]

Awesome utility box!! I need those plates.

[@robinsnyder8877]

Chris, in the instructions on the Amazon add for the Panda Lux, it says not to reuse the original X1C light with the new Panda Lux because of the power draw.. You plugged in both the Lux and the stock X1C light. Did this cause any power issues? If I install the Lux I would also like to use the stock light as well. Does the instructions that comes with the Lux say not to use both lights? Thanks for your time and I love your video's. Robin in Philippi, WV

[@ItsMeaDMaDe]

Hey. I know some have said not to but it comes with a splitter so I did it. I have seen no issue with it. I can’t figure why you wouldn’t the power draw is so little on leds just the knowledge I have on leds I can’t see it being and issue. But that’s just what I did not saying it’s the correct thing to do or not but it works fine for me.

[@kilcranp]

I've been running both lights for months now. No issues.

[@mikelarose5670]

The poop chute at 4:13 looks like a high heel from Pablo Picasso's Drag Race

[@Slurgical_3D_Terrain_Channel]

I recycle every thing, the poop from the printer, failed prints, those strips. They are perfect the tabletop gaining and terrain. They can be used for greeblies, terrain features. So I have no issues with those wastage since they are being repurposed.

[@jannickharambe8550]

You seem like a very likeable person great video

[@GuyH77]

Thanks for featuring my plastic base ramp :)

[@Serenityindailylife]

Dr Robotnik, theres a flaw in the panda touch. It wont let you log into the account via google even though you can log in to your bambu account that way. This means that half of the functionality is closed off from google users.

[@joaoprabelo]

I made a cabinet with a slit and an angle that shoots everything down to a drawer, where I can colect and clean up

[@TrippyyTreyyy]

you need to increase the temp on the build plate when printing with the design sides

[@perforations6234]

those lines you have in every print in the exact same position, look like it's some travel from one edge to another?

[@TheSimonarne]

I edited my purge size so it's quite abot smaller so i can print all the way up to the edge in that area

[@MadZaxx]

Awesome video my friend!!!

[@ItsMeaDMaDe]

Thank you very much!

[@MrDonXX]

I love it when reviews say "I was sent this stuff from the company but I wasn't paid for the review" One would think sending you the free stuff IS THE PAYMENT no matter what it is. This first on the list is not worth printing and is the opposite of the title but you knew that already.

[@PerfectPudding]

lol, facts

[@austindoyle552]

But that's literally not payment. I ran a youtube channel many years ago, and being sent a product for review is absolutely not seen as payment. I absolutely tore many products sent to me to shreds because they were subpar, many companies do offer to send the product along with a payment in hopes of buttering you up to give a better review. Believe me as a youtuber, you really don't make nearly as much money as people seem to believe, and receiving yet another product when you're already swimming in gear is far from payment, its just more space taken up in a drawer for half the stuff we get sent lol

[@cong-organic]

Most time you are required to send it back

[@Veksta]

Heaps of people give honest reviews on gear that’s sent to them. You must be new to KZbin lol.

[@MikeYamry]

It's a shame that the light strip doesn't match the color temp of the stock strip. The two tone warm and cool looks bad. 20:48

[@venorando3672]

And they shouldn't be on at the same time either. Too much voltage for the connectors apparently, according to Bambu Lab.

[@truey90s]

Pretty sure you can get a qr code sticker to put on the blank side of the build plate so the printer recognises it

[@chrislambe400]

For AMS spools dessicant cores NeedItMakeIt is brilliant. Makes sure to print in vase mode 6 bottom layers and 0.7 thicknesses.

[@mikec8101]

I bought / installed a panda lux a while back. When installing I saw the documentation said not to plug the original light into the board. That the combination of the two lights would exceed the expected current draw and cause errors.

[@3DPrintingPiper]

Thanks!

[@ItsMeaDMaDe]

You bet! Thanks a lot!!

[@venorando3672]

I really hope Bambu Lab starts selling their own touch screens that act just like the screens on the A1 and X1! I genuinely don't understand why this isn't a thing yet! I've also heard that there are support issues between the AMS and the Panda Touch screen, and that there are lots of other bugs on the touch screen.

[@jeffbarnes2014]

Can you use the Bigtreetech controller with The AMS on the P1S with no problems ?great video , thanks

[@MrTonglong]

I'm not sure if you noticed. But when you try changing either the nozzle or bed temp via the Panda touch panel, it doesn't set the temps on the printer. You can see on the LCD screen on the left that the bed temp is still 21/0c, if it was set, it would show 21/50c. I'm running into this same bug on my screen. You basically have to use the standard LCD to set temps. In your video, you can see the nozzle temp actually decrease by a degree while you're talking.

[@venorando3672]

I really hope Bambu Lab starts selling their own touch screens that act just like the screens on the A1 and X1!

[@B0M0A0K]

Can I ask where you found the print for your "utility box"?

[@mercutiojb]

I'm curious as well!

[@ItsMeaDMaDe]

I went ahead and put the link to it in the description.

[@B0M0A0K]

@@ItsMeaDMaDe Thanks very much!

[@jerrymacvaldosta]

P1S mods! the poop shoot is of X1 Carbon (not for P1S, it is to large).

[@AidanBree]

Yeah, I just discovered that too.... Which one did you go for?

[@dolmerfpv2109]

Hmm…. is P1S and X1 Carbon same size. ?

[@AlexLazarov-p7r]

I use the priming strips as material to solder parts together with

[@Thebigskullman]

It looks like you’re using both the panda lux and stock light at the same time… has that worked fine for you? I originally planned to use both too, I mean the multi port circuit board’s literally included with the package- but I’ve heard from users and even BTT that it only supports 0.3A of current so they say we shouldn’t use both lights at once. It’s so stupid for them to ship something and then say “don’t use it”- so if you’ve done it and it works fine then I’m gonna too

[@ItsMeaDMaDe]

So I wasn’t having any issues. I’ve been told by a lot of people not to have both so just recently unplugged the main light and just have the lux.

[@jzdaboss]

I also have a P1S but i've never noticed my printer throwing errors when i use build plates without labels on the front tab. Do you know if there is some setting that enables the build plate scanner? My P1S is from April 2024.

[@ItsMeaDMaDe]

Yeah I mis-spoke about this. The error is thrown on my x1 carbon. The p1s doesn’t. I tested each build plate on the P1s, X1 Carbon and A1. I realize I didn’t say the error is on the X1. Sorry about that. 🤦

[@chartle1]

@@ItsMeaDMaDe yea because it doesn't read the plate its one of the extras you get with the X1C. (I have both)

[@Spazz2sick]

Can you remove the screen the P1s comes with? Keeping both screens is a little aesthetically unpleasing

[@unc_matteth]

i still don't understand the poop shoot box. i have a small cardboard box that fits in there, and what's the extra work of picking up a box and turning it over to dump it in a garbage?

[@aeppikx]

i mean i printed some unneccessary things for my p1s like dustcover for almost ever hole it has , leadsrewcovers or frame for the display , but the purgestripbin is so fckn useless xd

[@tombo7719]

you have the same lines across some of your prints.. wonder why you are getting the same lines on diff prints? I will think on it. Thanks for the video~!

[@DennisCrawfordJr]

I thought I read that the panda touch might not be functional with bambu future updates.

[@ItsMeaDMaDe]

I didn’t hear that. My printer is up-to-date as of now and it works fine. I guess we will have to see when there is a next update. The panda touch has firmware updates so they could make updates to make it work if it doesn’t with an update. I guess I’ll just have to wait and see.

[@iainhay2823]

@@ItsMeaDMaDethe 1.04 firmware out today solves the problem, the beta has been working great. Sadly my panda touch also died today 😂

[@donjohnson19]

i heard now a days you can no longer use that screen on the p1s till bambu provides an update to the firmwhere some issue about it not shure

[@منايهالمسماري]

I want to buy one, would you recommend p1s

[@christiangoldenlok3758]

Noob question here. Can you print things over top the purge strip? I'm afraid to populate that area of the build plate. Thank you!

[@TSGear]

I'm using the same asa. The spool says 30 to 50mms. Just curious what speed you are printing at. Also are you printing 100percent infill for those?

[@joshhardin666]

poop chute is certainly the first thing people should print on a bambu p1s/x1c. it's really an engineering defect that they didn't include one as part of the body of the machine (maybe magnetic?) - where did they think all the waste was going to go? on your workbench? it just seems like a huge oversight... like a pencil sharpener that doesn't have a place to store shavings and they just go everywhere... that's what we've got on the enclosed bambu units... it's bleh.

[@chefboyerd3385]

Its not a defect, its a shortcut. I feel like theres multiple examples of these with bambu labs where they basically just know people can and will make/print additions so why spend the money on it themselves? Frustrating for sure but of course always looking for ways to cut costs on themselves.

[@NoiseMakerX]

No matter what they may have included people would have printed alternatives anyway so why include it at all?

[@joshhardin666]

@@NoiseMakerX so that it's turnkey for people who are brand new to 3d printing. even if they included a decent model for one that they suggest printing in the manual, it could have been ok i guess, but the p1s is so close to being an amazing turnkey new-to-3d-printing experience, a little more polish would have been better. that and the absolutely shitty camera are my only 2 big complaints about it.

[@NoiseMakerX]

​@@joshhardin666 The P1S is my first printer and I don't miss the poop chute and I think camera quality is fine for it's purpose, but sure it would have been about a dollar for it to be better.

[@joshhardin666]

@@NoiseMakerX I keep my printers in a different room than I'm usually in and like to monitor them in real time while printing. further, I like to stream my printing process to twitch and the camera that's included isn't up to snuff for either of these. i'm even ok with it being a 720p camera, the big problem is the frame rate. we only get maybe 3fps and it's pretty laggy. by the time i see that it's failed, it's already too late to hit pause and save a print.

[@WoodworkJourney]

I thought the Panda didn’t work since a Bambu update. Is that fixed by Bambu or BTT now then?

[@PerfectPudding]

Glad I didn't buy it - had it sitting in cart. Thanks for the heads up!

[@YaNeK92]

@@PerfectPudding Waiting for Bambu to release their own version to purchase separately soon.

[@junkins]

Can you use the screen upgrade with the AMS system?

[@joshwpro4499]

5:28 Haha, you have a 3 D Printer workshop and talk about not having a certain type of purge bin. You have a freaking 3d printer workshop. Make it yourself. that's what 3d printers are for ^^

[@subject8123]

I found a poop slide and have a trash bin next to my the table. All the poops and purge strips and support go in there

[@_-_-_Marshmylo_-_-_]

where is the file for the side spool holder? It's not in the description

[@ItsMeaDMaDe]

I missed putting that in. Sorry. I just put it in the description

[@_-_-_Marshmylo_-_-_]

@@ItsMeaDMaDe ok tysm needed this

[@andyhunt871]

Can you remove the panda touch screen and still use it? Or does it always have to be on the dock?

[@bretthopenwasser2267]

Is a PS1 worth $550.00 slightly used. Looks brand new?

[@OssibotREAL]

Do these mods work on the x1c or is there a separate video?

[@jondoough]

Any fix for the really really really crappy camera?

[@CNCnStuff]

What would be great is if the touch screen could replace the car radio screen, rather than be in addition to it - even though I appreciate the touch screen does it all.

[@chuckm3520]

How well does the panda touch work with the AMS?

[@tilross2761]

Can you please show us how to print small part with fill bed with copies option, I want to print small model but it always fails🙏🏻🙏🏻

[@tilross2761]

In bambu lab studio, should I add more heat of what I can do with textured PEI plate

[@jeannordstrm3935]

i have never seen a error on my P1S i have even printet on my ender 3 buildplate

[@ItsMeaDMaDe]

Yeah I mis-spoke about this. The error is thrown on my x1 carbon. The p1s doesn’t. I tested each build plate on the P1s, X1 Carbon and A1. I realize I didn’t say the error is on the X1. Sorry about that. 🤦

[@zoraidacruz8145]

What do you do when the filament is stuck

[@boisalten]

Can i use a small ipad instead of a Panda Touch?

[@iFail90]

why do ppl with bambu printers ALWAYS put the logo on their mods :D (i only have bambus myself but i dont get it). Thank you for the video. The best for upgrades ive seen so far. I will buy some of them when my P1S finally arrives.

[@startchbrain]

Wy do you even use the screen? I have used it 3 times in 1k hours of printing

[@jonnymeyer8572]

Love the video, but hate the audio you recorded. Some tips: ) move your mic further away from your mouth. 2) stop projecting your voice. It sounds like youre trying to yell to be heard, and its an utterly exhausting thing to have to listen to in recordings. 3) reduce your mic gain a tad. Too many pops and plosions.

[@noiricha]

At 20:23 there is an omission error - it should state at this point that you - plug the 2 male plugs into the female PCB board. This step was missing.

[@Thebigskullman]

Do you use both lights at once? I wanna but BTT “warns” not to because the current its rated for tops at 0.3A, so I dunno if it’s safe for the hardware to run both lights at once.

[@BuildingwiththeBlackDog]

Do you have a link for the side mount spool holder please.

[@ItsMeaDMaDe]

Sorry about that thought I had it in there I just put it in the description.

[@psg5004]

My P1S doesn’t scan the buildplate. Are u talking about the X1?

[@trade_design23]

Purge Strip Holder?? So... a simple trash can does not work anymore?

[@Personnenenparle]

Dude.. Just print the QR code and stick it on the build plate...

[@bsr3280]

Need help with active Foaming LW PLA setting. 1 wall, 2 or 3% infill for printing RC airplanes. It prints pretty well, but in some areas, it’s just like gaps. Don’t mind the stringing, but would like to get rid of the waffling gaps. Please help.

[@raphael153]

Dafür gibt es im Slicer modifier. Diese verändern nicht die Form der Objekte, sondern die Parameter können in diesen Bereichen geändert werden. Besonders gut zur Verstärkung kritischer Bereiche ohne andere Stellen unnötig schwer zu machen.

[@planetbuster]

BAMBU CARBON X1 POOP SHOOT (PURGE BIN) not Printable on P1s, its to big....

[@Gambit_Falls]

i am having the worst time with the ams system could you do an "all you need to know" tutorial on the ams system how to use it, how to load the filament into the printer, etc, etc. i have a P1S and its great but i cant figure out the ams system and im ready to just use the spool holder instead and cut out this headache. i am a first time user and ive made 2 benchys so far but i have to fight with my ams just to get a print! yes i realize it is almost certainly user error but that is why i am requesting the video. any help from anyone would be greatly appreciated!

[@ellerycadel]

the purge bin cannot be printed on the Bambu printer (too big) - well that makes no sense!!

[@meawayfromhome]

I printed mine on the p1s, had no problems.

[@AidanBree]

​@@meawayfromhomethe one linked is for the x1. Did it work for you?

[@meawayfromhome]

@@AidanBree I used the one from cleberlop from printables. When you load it will be outside plate! you just have to move it and it fits.

[@AidanBree]

@@meawayfromhome Thanks!

[@DiomedesDominguez]

Only one of your recommendations is truly a mod, the purge bin and holder, maybe the Beveled inside Edge and that's debatable. All others doesn't improve the quality of my prints, nor the time or the experience during maintenance. Please, review the title since the rest aren't really mods that worth.

[@HarryBroadwell]

Has anyone tried to operate the P1S without the original control panel so you can mount the Panda Touch in its place? Will the printer even function without it?

[@robertzieg3893]

Are these Bambu labs approved mods? This is a legitimate question not me trolling. I feel really uncomfortable modifying my really expensive printer that works literally perfectly, unless it’s Bambu Labs approved. They do offer some of their own upgrades and they work great.

[@ItsMeaDMaDe]

These are not Bambu approved mods. This is for those people that want to tinker with there printer

[@HughCStevenson1]

You got stuff free. That's enough to cast doubt on impartiality. If you give something a bad rap...no more freebies for you. Next time just buy it.

[@Shenandoahleather]

The lawsuit has really made me think twice about purchasing another BL printer. Had my mind set on the P1S after owning the A1 Mini, but I'm holding off for now.

[@kwangL0128]

Buy the BL

[@IrocZIV]

I'm the opposite, I wasn't in a hurry, but now that the lawsuit is going, I think I want to get one incase Stratasys wins... I suspect all printers are going to be affected if that is the case...

[@Shenandoahleather]

@@IrocZIV you could be correct. That’s another reason I’m won’t buy another BL. If something happens to it and I can’t get parts it becomes a brick. A Prusa, being totally open source, I can fix.

[@Obtuse94]

If stratasys wins every piece of the lawsuit, it will affect all your printers, open source or not. Open source printers will have the affected Git repos get taken down overnight. Stratasys is a patent troll that doesn't care (or probably doesn't want) the hobby level machines to even exist.

[@Shenandoahleather]

@@Obtuse94 that’s one good reason to use printers offline and have a dedicated comp offline as well. Then again. Chinese companies aren’t going to abide by U.S. law. Never have. And having China take us over after we default on our debt (unless we raise taxes to 90%) they will care even less. Wait. Maybe I’m making the case to buy another Bambu 🤫

[@johnfazzio1743]

I need help with my x1c bambu please help me i don,t know what to do

[@Itcr0]

Panda Lux LOL! Get a LED strip. GTFO

[@MentalD-Fox]

It's kinda dumb they don't have that light on USB. If it was on USB you could use both. And the swappable nozzles would be awesome.

[@PeterAgostiniJdcap26]

Don’t pull the tape for the magnetic 🧲 light you’re be sorry . Seriously.

[@trade_design23]

Poop Holder - So....., you never empty the trash in the kitchen either ?

[@cliftonhead9665]

Did you pay for the items your installing, Lux LED. I ordered the LED light when I order the Panda Touch which work well. The problem is with the LED lite, their customer service. After installing the lite I lost the camera, printer stop printing and control screen shut off. Remove lite and reconnected the OME lite. Pulled control screen off and disconnected and reconnected the plug on the back of the control screen. Trun printer back on and the printer starting printing and the screen works. But no camera. Contacted customer service for help and got nothing but bullshit from them, also ask for refund and return have not got anything from them whatsoever. Then went on some P1S and Bambu forums and found out what happen to me has happened to others with the same no customer service help. BTW still no camera. Total piece of crap if you ask me.

[@ItsMeaDMaDe]

Oh man. I still have my camera and it’s working just fine. I haven’t heard of this issue at all. Did you try to do a factory reset on the printer? Maybe that would get it back. Sorry you’re having issues with it.

[@cliftonhead9665]

@@ItsMeaDMaDe Did you pay for the Panda touch and Lux Led or did they send them to you

[@jsflood]

Holy poop! So it's back there it ends up lol. Great tip, I need a poop bucket, wonder how much poop it's back there now. I thought it already was a poop bucket somewhere in the printer. Apparently not lol. Thank you for this great video.

[@kitchenbriks3685]

Whatever filament you’re using on those first layers is kinda junky. I use those plates and without changing anything I get perfect squish. Polymaker and Elegoo filaments do the best.

[@Fstrike]

You can't even print the poop chute on the P1S, needs to be mentioned.

[@verdejt]

I printed it no problem.

[@bsr3280]

Not a clue what you are taking about????

[@slappomatthew]

Fake carbon fiber is so cringe that even real carbon fiber is lame now