Basic CH3 channel 3 operation based on a Futaba T3PV what can you use it for?

[@ChristophthePug]

Hello. I can't seem to find anything about how to set up CH3 to control the Tamaya three speed transmission on the Toyota Hilux. Do you have any suggestions? Thanks!

[@telecomandorc]

I am not sure how the 3 speed works. The 3ch is more of a 1-2 deal on this Tx.

[@ChristophthePug]

Thanks for the reply. It looks like the Flysky 6CH might work, and they aren't to pricy. After 30 years I'm getting back into RC's, I have a lot to relearn! @@telecomandorc

[@louisabelhard9596]

Hey i have a question, so my receiver transmitter is a sanwa mx6 and in the channel 3 is says aux so can i use that aux/channel3 for servo?THX and even if i can use it for servo how do i make it move? Kn the EPA? orr

[@telecomandorc]

I am not familiar with the mx6. I only have access to the MT14 and MT5. But on both you can use the 3CH to operate a servo in on/off mode. There is a way to do a winch, but I do not recall how at this time.

[@louisabelhard9596]

@@telecomandorc alr thanks bro

[@telecomandorc]

@@louisabelhard9596 My pleasure.

[@drakedrizzy9413]

My problem is my servo is left going right and right going left how to make it go the right direction

[@telecomandorc]

Reverse CH1. It is in the menu settings. Use the left or right button until you get to "REV". Then reverse the channel. Below is a video with all of the settings. Go to minute 16:57: kzbin.info/www/bejne/qZ7UlIuuqc6hnKs

[@drakedrizzy9413]

@@telecomandorc thank you brother

[@telecomandorc]

@@drakedrizzy9413 My pleasure.

[@charlesyoung8600]

Can you tell me which side of the receiver is positive and which is the negative side.

[@telecomandorc]

Left to right: signal, current, and ground. So, the right side is negative, and the middle is positive.

[@Youngking54321]

Hey brother I have this same transmitter I recently installed a gyro on my arrma limitless, soon as I start catching speed the front wheels would wobble very bad, this started happening when I installed the gyro. Now my question for you is how do I add gain (tune) the gyro with the transmitter (which section) will the mode be in?? Also thanks for the help!

[@telecomandorc]

EPA Then you can lower it to 0% or move it up to 120%.

[@davidemicheli4240]

I can use the ch3 for a servo winch?

[@telecomandorc]

You could. You could make a little dump truck.

[@davidemicheli4240]

@@telecomandorc nice, because on your clip the 3ch seem just a 2way switch, I'm going to try

[@davidemicheli4240]

@@telecomandorc nope it's just a two way switch, hoped for a three way switch

[@telecomandorc]

@@davidemicheli4240 It is an extra cost but have you considered a Warn winch controller? RC4ZE0130

[@davidemicheli4240]

@@telecomandorc i don't need a controller, I'm going to reverse the Channel every time 😁

[@TurboTheTerrier]

Quick question. I'm new at the rc world and I have the futaba 3pv. I'm having trouble with the throttle. It's going forward when the trigger is moved up instead of when pulling the trigger. Quick help?

[@telecomandorc]

It depends. If you push the throttle to brake and it goes forward, and then pull it to throttle and it brakes, and you pull it back a second time and it reverses, you need to go into the menu setting and reverse Ch2. Now, if you pull the throttle and it reverses and you push it forwards it shots forward instead of breaking, you need to go into the esc programing and reverse the rotation of the motor from CW to CCW or vise versa. Here is a video I have on the Futaba 3pv settings: kzbin.info/www/bejne/qZ7UlIuuqc6hnKs Here is a video I have about setting the correct motor rotation: kzbin.info/www/bejne/kGWXqpKhjJqrkK8

[@TurboTheTerrier]

@@telecomandorc thank you! So I don't use reverse due to only racing oval track. So when I pull the trigger, nothing, and when I push the trigger up (reverse or brake) that seems to be the throttle

[@telecomandorc]

@@TurboTheTerrier Just reverse Ch2 in that case.

[@abyss5350]

Wow I’m first I win good ideas for the 3rd channel I like the lights idea I may be incorporating that one

[@telecomandorc]

Awesome!

[@fabricioaraujo6783]

how to use 4 channel futaba 3pv?

[@telecomandorc]

On the 4PM it's just a switch behind the wheel where the ch3 switch is. The T3PV does not have 4ch unfortunatly.

[@Balberts123]

It has 4 channels ( 3 + 1 )

[@socwyvern9745]

Long story short I need 2 to be throttle and 3 to be brakes.

[@telecomandorc]

Brake lights 😁

[@socwyvern9745]

@@telecomandorc no, brakes. I’ve got an old Tekno conversion kit and I need either a 3 or 4 channel receiver. Channel 3 needs to be fully active and be inverted from channel 2. Functionally on the radio end it would be brake lights.