Best Dolphin Pool Cleaner Models 2024 Comparison Chart Breakdown

[@thedolphindoctor]

NEWS AND UPDATES: Thanks for watching! Pelican shops will have most of the models on the chart. They also offer an ENHANCED warranty on most models, meaning, that they cover not only part costs but labor and shipping costs. They also get it done MUCH faster than dolphin directly or other stores. I will also most likely be the one to fix it when this occurs! No other store will cover shipping to and from and most do not cover labor. The goal is to let you have 100% peace of mind just in case it happens. Here is the link: pelicanshops1.com/collections/robotic-pool-cleaners I WILL ALSO ATTACH NEW INFO OR CHANGES THAT HAPPEN THROUGHOUT THE SEASON ONTO THIS COMMENT BELOW THE REST SO CHECK THIS AS INFO MIGHT CHANGE MIDSEASON THAT WONT BE REFLECTED IN THE VIDEO Feel free to comment in the comment section any questions you might have! I know not every little detail could be covered in this video otherwise it would be a decade long. Ask away if you have some more specific questions! the goal is to make this video as well as the comment section a resource of knowledge people can go to without any "BS" marketing confusion. Update 1: (04.23.24) Liberty 400 gen 1 will only have 1.5 hour cycle. Gen 2 is planned to have 2.5 hour but I'm unsure when that will happen. The video states it will have 2.5 hours but dolphin has clarified not at first... Update 2: (06.18.24) Liberty 400s have finally hit shelves. There are multiple coupons out for E70 bringing the price down to $1899 ($100 off) from most places like Pelican. Being the same price as M600 makes this worth considering however M600 still have the rebate on it while E70 does not

[@MichaelRaduazzo]

Very informative videos. I recently purchased a 27-foot above-ground pool. Can you do a video about vacuums for above-ground as well?

[@thedolphindoctor]

@@MichaelRaduazzo Essential dolphin offers the the E10, Escape, T15, S50, Active 10 for "above ground units" that will only do the floor of the above ground pool. HOWEVER you can use any unit in reality (although it might be overkill). I would say you can go up to the S300 column on the chart in the video without being considered overkill or look at the models I mentioned in the beginning of this comment. They have the same specs as the first column but will only do the floors

[@DaveBigDawg]

What is the expected life expectancy of a CC plus

[@michaelraduazzo6146]

I've never seen a Cayman for $599. Find me one and I will buy it on the spot. Great video otherwise

[@thedolphindoctor]

@@michaelraduazzo6146 yeah. unfortunately the stores might not follow MSRP. that's why I would suggest finding an equivalent like an E20

[@kjb7229]

I can’t thank you enough for such a comprehensive, no BS, explanation on the different models. I’ve wasted so much time trying to figure this out on my own. Excellent comparisons of the models and differences. You have a talent for explaining things without wasting a lot of time - thanks. I had a few candidates in mind; and, after watching this, I have decided on the M400 and ordered today. It is so rare to find an English speaking, knowledgeable person that I can call and get my questions answered!

[@thedolphindoctor]

thank you! appreciate the positive comments

[@salviofossa4587]

This is literally THE BEST pool cleaner video available. NO QUESTION. I have watched so many of these videos. They are by in large worthless. This is so thorough and so clear. I have also bought three robots so far and have returned all three prior to watching this. Dying for information. This was so helpful. I only wish you covered Polaris as well. Obviously, I understand why not. Amazing. Thank you so much!

[@johndotson2857]

Which one do you recommend? Which one did you end up with?

[@haydnbrasher9939]

Dude this video is exactly what I needed! There are so many dolphin models its hard to tell one from the other. This video is really well put together and has a ton os useful information for anyone looking to buy a pool vacuum. Thank you!

[@thedolphindoctor]

Glad you liked it! I know its insanely confusing

[@ronwilt940]

Almost! I almost bought the Dolphin Premier since all the fake reviews and videos promoted it so much. I watched many of them and all the Google-sponsored reviews that just can't be trusted anymore. I am happy I came across this video. I am purchasing the M600 instead. Top load basket vs. upside down with an old bag design stuffed into a small chamber. Triple motors with dual scrubbing brushes vs. two motors vs. no active brush, caddy vs. no caddy, gyro vs no gyro, wi-fi app vs. none, manual drive and three cycle times vs. one, full bag indicator, smart nav with a new design vs. outdated Premier. I'll get the $100 rebate on the M600 and spend the extra $400. It is worth the difference to me.

[@thedolphindoctor]

I'm glad this video helped you! your kind words mean a lot.

[@frankgrubb1]

I'm ready to upgrade from my Dolphin DX5 plus that I've had since around 2010 or so. It still does a good job but I'm so tired of cleaning out the bags and the remote hasn't worked for years. I am considering the E70 but now I'm considering the M600. Thanks for the video!

[@salviofossa4587]

Also, you're the only one who said what I found to be inconvenient. The bag with those cartridge slots it's absolutely ridiculous. Every advertisement and review talked about this huge bag but you stuffed it in that small cavity. The upside down loading and unloading. Again thank you!

[@thedolphindoctor]

yeah now you know my pain! people fall for that marketing ALL THE TIME. The video helps whoever watches it but only a small fraction of people ever see it but its good it helps who does see it for sure

[@rbackk]

Great video. Do you see any improvements across models in not getting stuck in floor drain covers? I got a Quantum when my old DX3 died and was disappointed to find that it too gets stuck.

[@thedolphindoctor]

unfortunately the main drain issue is really dependent on the drain itself. if the drain is to large to the point where the unit can get fully pinned on it most robots will have an issue EXCEPT for the M400 and CC SUPREME which have that 3rd brush in the middle which allows it NOT to have a spot where it can be pinned up. those two units are pretty much immune to this issue. However units with dual drive motors (like the m400, cc supreme, m600, active 60, e70) also fair better due to moving faster and having usually momentum to get up and OVER compared to up and STUCK. Another remedy you can try is to run the unit without the pump running as sometimes the main drain suction and cleaner suction can create an effect where they just get stuck to each other in a way.... Sometimes that solves the issue all together. The unit might get stuck but most of the time it has fail safes in place to notice its stuck and get off. it might take 5-10 minutes but usually it can get off.

[@kenkaplan5468]

This was one of the most informative videos on this topic. I finally understand all the features and benefits especially since just because it's more money doesn't mean it's better for your pool. Thanks.

[@thedolphindoctor]

Glad it was helpful! I appreciate the kind words

[@I_FosterKid_I]

Commenting again on this video for the algorithm. Your content is excellent for the pool owner community. You’ve mentioned making it in the past, but please make a Polaris vs Dolphin comparison video similar to what you did with Aiper!

[@thedolphindoctor]

thanks! I will make the video eventually. Just want to make sure its done the right way

[@coder6083]

Thanks for taking the time to put this information together. You are absolutely right about which models are being pushed on KZbin.

[@thedolphindoctor]

I'm glad the video helped!

[@jriver39able]

Hey man, just wanted to say thanks for the review. I did order the M400 from from Pelican Shops because of this video. Best product I've purchased in a long time.

[@thedolphindoctor]

Great to hear!

[@easyperl]

As a content creator for multiple channels... I see the effort and just have to say that with this video, you are doing god's work. Great rundown of the models and differences. Our old dolphin 4 deluxe died and I have been stuck in analysis paralysis for about a week on what to buy. This helped me choose the discontinued dx4 for $100 off locally and order a ultra fine filter set online (so both for just under the normal price of a dx4 or... basically 100+ off the quantum that I was looking at).

[@WendyRutledge-q8m]

By far the best video I've watched to help pick a new cleaner! Thank you sooo much for taking the time to describe the differences and build the amazing chart for reference. Great job!

[@aldenpines]

Best video on pool cleaners, period. I wish you had done this 2 months ago before I watched several scores of confusing (and lying) reviews of these robots. Thank you!

[@thedolphindoctor]

I'm glad you think so highly of it. Unfortunately your situation is a common thing that ends up happening. I try to post as much as possible on forums / groups online to help spread that awareness but it only goes so far.

[@HendersonMorne1]

Hi - just finished building a pool. Your video was fantastic and very informative. Noticed it has been a few months since this video - was hoping you have an update on the liberty 400? I am considering s400 but have been told by many to go cordless? The liberty looks the part but appreciate that it is fairly new hence I can’t find many reviews on it. Hope you can help

[@thedolphindoctor]

Liberty 400 still only have 1.5 hours. once it hits 2.5 it will be worth considering for sure. Jury is still out on how long those batteries will hold up as this is the 2nd year dolphin has cordless out. they have actually been very good in the reliability section as the only issues ive run into are a few chargers breaking where it was confirmed the customers were charging it in the sun which the instructions STATE NOT TO DO. Cord is still more powerful in my opinion as of now. if you take care of the cord and keep it neat you wont have an issue.

[@Drivelikeitzstoln]

Thank you!!! I'll probably be calling to order in the next few days. Trying to decide which model to get. I will probably have to call to see what is available

[@VCMCmusic]

This was an amazing video! I just sent back the Beatbox Aqua sense pro. That thing didn’t work for me. So I needed to understand all the different models dolphin makes and you helped tremendously!

[@thedolphindoctor]

great! I have been hearing the same with multiple people about the BEATBOT. I think its important that you leave a review on their site or amazon to share your experience. the reviews sound to good to be true based on how many people have told me bad things about it. They might be censoring the bad reviews. Glad the video helped!

[@VCMCmusic]

@@thedolphindoctor does the ultra fine filters come in the box already or do I need to purchase separately? Definitely something I’m going to use most of the time

[@thedolphindoctor]

@@VCMCmusic depending on the model. some online models or lower price point models do not come with them

[@VCMCmusic]

@@thedolphindoctor guess I didn’t say the E70.

[@tomcoulon1542]

These videos are simply the best there is on Dolphin Robotic pool cleaners. I wish I could purchase from this company. Watching in Mexico. 👍

[@thedolphindoctor]

thank you!

[@JeanneWalker-r2g]

Thank you for your quick reply. I know the pool is large, and it probably will take two days to clean it all. But, do you think it can handle the corners and the slant down to the deep end and back. If you say no, then I respect that. Thank you

[@thedolphindoctor]

it should. maybe not the absolute corners but definitely the slants down.

[@genesoohoo944]

Appreciate your honest opinion and criticism of all the Dolphin models, most informative youtube video out there regarding Dolphin cleaners. Pelicanshops also looks like a trusting authorized reseller.

[@robinabrams8849]

Hi, I just bought a home with a med size above ground pool. I was recommended the Polaris by friends who have had it for several years and swear by it. After reading all the reviews, I don’t feel I want to move forward with that model. I was surprised to hear the negative reviews. I do know from listening to your videos that I want one with both fine and ultra fine filters, active brush, I don’t care if it’s cordless or not, waterline, side and floor cleaner, 3 motors if possible but will settle for 2, preferable rebate but want it ASAP, active brush, app would be nice, 24+ mo warranty, Caddy would be nice but not necessary, basket design preferred. I’m looking for convenience and super ease of use

[@thedolphindoctor]

M600 sounds like what you want but you could get away with S300 if you wanted to save $$$

[@angelabraun-uu4kd]

This is the best video I have found so far to try and help me decide what product does what

[@hinesmt]

I wish I would have found this video a week ago before my Sigma purchase. I even saw an M400 at my pool store and didn’t get it and ordered the Sigma. But, the Sigma clean is great! It took things out of my pool that I had no idea were there including a ton of dirt.

[@thedolphindoctor]

yeah the sigma can be very misleading.

[@dgasmd1]

Great video and easy to follow chart/comparison. I've had a Nautilus cc for 4 years and have replaced almost every part in it several times. Tracks always come off, sooner or later despite what you change. Replaced the cord after it broke in a spot. Worked for 2 weeks and now "attempts to come on" but nothing. Thinking it is the "brain box", but tired or throwing money at it. Sent it once to Nautilus. Returned with the same new parts doing exactly the same thing. Very frustrated. Have a 8-9000 gal pool at home. Need something good, does walls, no need for caddy, no wifi/bells and whistles, works daily, AND reliable. Suggestions to narrow it down??

[@thedolphindoctor]

good questions. Was the robot left in the pool most of the time? used when the chlorine was really high (like after shocking it, or maybe after using pH- chemicals)? you definitely should not have had this many issues. However the chlorine exposure does cause everything you have said over time. See my other comments on the leaving it in the pool topic to see what I mean. As for suggestions on what to go with next. You can go with a basket design so it is easier for you to maintain and empty out. The basket designs have less parts as well which in my mind is "less that can go bad" down the line. However basket designs are definitley geared more towards "keeping" a clean pool compared to CLEANING a really dirty pool. If you want something heavier duty than M400 would be an option Id look at as the value is there. Although it has wifi it does not rely on it.

[@dgasmd1]

@@thedolphindoctor yes, it was in the pool almost all the time. Lazy me figured it is meant to be in water and set to go off daily, so why add the work of in/out daily? Like I said, when it worked, especially the first few months, it was more than plenty for me. Poll does need a good cleaning now, but once cleaned it doesn't really need it daily. I just did it because it was already there. I'll look into the suggestion above, but hoping to spend a lot less than that if at all possible.

[@thedolphindoctor]

@@dgasmd1 At that point look at S200 or stay with CC plus, I think knowing that the issue was indeed the chlorine exposure and just being submerged too long I think youll have an improvement on the next one regardless of if its the same unit or different

[@rhouse4958]

Thank you so much for this video. I'm a new pool owner and I have been so overwhelmed with figuring out which robot to buy. I only have a 12 x 24 salt water pool in Tampa. I want to make sure it cleans my waterline. Had no idea about the active brush. I don't have a cage and bump up against a conservation area (trees). I prefer to purchase at a brick and mortar. Which dolphin do you recommend?

[@thedolphindoctor]

depends on how bad the pool gets and how quickly. you can go S200 as it will do waterline but that unit might need to run more throughout the week since its not as strong as an M400 or M600. If you want a unit to run less but still clean just as good than M400 or M600. M600 if you really want the basket but also the power upgrades of M400. I leaves are an issue constantly a dual drive unit with higher suction might fair better (M400, M600) or run the weaker units more throughout to keep up

[@yrefai]

Excellent video! Question for you. I am deciding on M400 vs M600. I notice the M600 does not have the dual stabilizer the M400 has. Why is that? And does that make the M400 more effective at the water line? Also, I don’t understand the difference in the filter designs between both (cartridge and basket). Thanks.

[@pegg1258]

Watch the video and you'll see the difference between the filters. I have a dead Dolphin s300i, and loved the basket design. Very easy to spray clean and empty. FWIW, after this incredibly helpful video, I'm replacing it with an M600 due to the active brush, basket filter and total of 3 motors. I live in NJ, so will buy from pelican, and am looking forward to the store-supported warranty/repair work, if needed. FWIW, there is currently a $100 manufacturer rebate during May (last day today) for the M600. You can see what other models have rebates on the Maytronics website.

[@SheriMalcolm-p9e]

I would like a reply on this one as well!

[@kentshadwick6354]

Thank you for the excellent comparisons and comments. Considering the filtration and extra features of the S400/Active 40, is the additional $330 CDN (in my market) worth it over the S300/Active 30 in your opinion? Would the filtration system of the S400 be all that different from the S300? Thank you.

[@thedolphindoctor]

I would say if you are gonna use the different cleaning cycle options and times as well as the pick up mode the S400 would be worth it. But if you only plan on going out and hitting that power button manually most of the time than the S300 would be a better value. The pick up mode is nice on the S400 though as your not putting strain on the cable when taking the unit out of the pool. HOWEVER you can use the manual drive mode on the s300 via WIFI to essentially do the same thing. The filtration difference is nice but should not be a sole reason to upgrade.

[@igorla7977]

OK, I have watched their videos. They are really well done. I bought M400 through Pelican for about 230$ more than the other known distributor under the promise of their superior insurance. My summary after the 4 weeks of using it. Positive - relatively easy to operate. In the areas where it goes, it cleans well. It climbs the walls. Nice looking. Negatives: 1. The caddie is a joke, very difficult to store the cable on it, the power supply falls off easily, just some cheap plastic design. 2. The M400 does what it is supposed to do, but - it goes in random ways, so we have to run it at least twice to cover most of our smaller 15,000-gallon pool. 3. It does not climb well on any steps, even deeper ones (very rarely). It leaves the corners "green". 4. The application is VERY simple, with no map or anything just push the button. We will keep it but Please do yourself a favor and study more.

[@thedolphindoctor]

Unfortunately no cleaner is going to get into the absolute corners of steps. Due to not being able to fully fit on each step individually. Not many cleaners can and if they do they are too small to cover the pool in a convenient amount of time and will fill up before it's done due to being smaller with less space. The caddy. You are supposed to wrap the cord by hand before putting it on the caddy wrapping the cord around it won't work well due to how the cord is already in a "memorable" coil shape out of the box. Trying to coil it tightly around the caddy is fighting against that. It's very much a trade off with some aspects of the cleaning across any cleaner. Do you want more suction power then you will have less filtration quality. Do you want to fit it smaller corners or on steps then you need a much! Smaller unit that will fill up before doing the whole pool. Do you want more app features and such, then usually the cost goes up as well as more glitches as most people have been saying about beatbot and other brands. My research is done with now 7 + years in the field. I think I know a thing or too.

[@tiffgreenapple]

Thank you so much for this!! Immediately subscribed 😊 I’ve been looking for the right robotic cleaner and you have the BEST video by far. Do all of these cleaners work for a kidney-shaped concrete pool (3 to 10 feet)? And do the cords get tangled often? I’m looking at the Aiper Scuba N1 but I’m concerned with its power and ability to clean a freeform pool

[@thedolphindoctor]

I would definitely stay corded at this point for cleaning performance and longevity. they will handle a freeform shape pool. the cord being tangles is easy to avoid if you unplug the cord from the power box when its done and taken out. otherwise the tension just gets worse and worse and causes the tangling. if you keep it neat you wont have a problem

[@tiffgreenapple]

Thanks so much! We’re going to go with Nautilus CC Pro based on your review, appreciate your help and the quick response!

[@thedolphindoctor]

@@tiffgreenapple awesome!

[@AP-el1pi]

Hi, thanks for this great video! I live in Italy and have a 12 meters pool. My local pool shop who sells and repairs dolphin cleaners recommended to stay away from all the "new design" models with filter basket below 1500$, because he says they break more often. He instead recommends the "older style" models with the dual filter cartridge on the top and the big swivel handle. However some of those models only have the active brushing through a third optional brush and he says it's not worth to have it because it doesn't add much to the cleaning power but breaks often. I'd love to hear your opinion on this! Thanks again! Angelo

[@thedolphindoctor]

I can see their point (sort of) but I feel like the breaking more is a result of being taken care of improperly (noticeably high chlorine exposure and being left in the pool way to much) that causes these issues. not the design. The older designs actually have more moving parts in them compared to the newer basket design.

[@lanad.4647]

I own a 12-yr old Dolphin Supreme M4. It's a powerhouse and works great for my 32' long pool. I am wondering which one of the presently-manufactured models most resembles the Supreme M4? Mine has ultrafine filters, 2 gray brushes and one active brush in between them. I've done maintenance on this M4 myself and feel as though I know the machine inside and out--it's super easy to maintain. Is the M400 or the M500 most like my M4?

[@thedolphindoctor]

M400 is the new M4. M500 isnt in production since 2018. M600 replaced it

[@michaelpetrik4395]

Thank you for this informative video, much appreciated. I have a small 10 x 20 ft pool, will a cordless be good enough to clean it?

[@thedolphindoctor]

It would be yes!

[@mtc5583]

This is a great video that helped me to buy one that is within my budget and needed performance. I just bought the Proteus DX4.....I'll update once I receive and utilize. Thank you

[@andrewvillavicencio8496]

Thank you! My Triton PS I bought back in 2019 just started to make grinding noises and not move anywhere. Cannot find any replacement gears anywhere, time for a new one, bummer. Thanks for the reviews!

[@s.p.c.3724]

Thanks for the video. I have a 30L x 12W, gunite pool with a slope going from 3 to 6 feet in southwest FL. I am trying to decide which robot will be best for me. I get some leaves and mulch in my pool so I am considering a basket design; however, I don't mind picking up most of the leaves with the net if needed. Do I need the app and the caddy? If no, I am wondering if I can get away with the some of the models in the standard series, namely the S200, Quantum, Active 20. I know I want the ultra fine filters. If I should have the app and caddy, I am considering the S300, Active 30 or T45. The CC Supreme and the M400 with the 3 motors are intriguing but I don't know if I need all that power and I am wondering if I should have the basket instead of cartridge. As you can see, even though I know a lot more after watching the video and looking at the chart, I still don't know which model I should buy. Thanks in advance for your help.

[@thedolphindoctor]

WIFI and caddy aren't necessary. they are there for people who want the added convenience but they are not necessary. Netting/ brushing will always be something you might have to do if the pool is bad and I always suggest doing it for people who open up in the spring. You being in FL don't need to worry about that part lol. S200 would get the job done, its designed to KEEP a pool clean. where M400 is much more efficient in cleaning a dirty pool. BOTH UNITS can do that but it just take S200 longer to do so, more cycles. You also need to run S200 more through out the week where M400 not as much. I would say look at those two models if you don't want WIFI. ALTHOUGH m400 has WIFI, its not reliant on it... The value is there to make it worth its price regardless if you use the WIFI or not. Feel free to call me at Pelican 9733134424 and just ask for John during the week days. Its definitely a complicated purchase to make

[@s.p.c.3724]

@@thedolphindoctor thank you John for helping me select the best option for my pool and my location. I really appreciated the consideration to the different models I had in mind and how we came to decide on the M400. I am in the middle of a seawall replacement project, so the M400 will be put to the test right away as they are kicking up a bunch of dust.

[@nickdoyne395]

hi, tremendous comparison video. I have a very old pool, which I believe is concrete. I've been paying my pool guy the past two years because he thinks all these machines will basically break because of the concrete. this year, I'd rather save money by buying my own vacuum. Any recommendation for an old style pool?

[@thedolphindoctor]

concrete wont mean anything. As long as its not left in high chlorine you should be fine. concrete might wear brushes and tracks slightly faster but if you take it out when not in use that will help. if it lives in the water submerged it makes it easier to have parts wear down due to chlorine exposure

[@nickdoyne395]

@@thedolphindoctor thanks for the prompt response. I know it’s hard to say, but I have a lot of trees around my pool, where I clean it multiple times daily. I just purchased a Betta SE solar powered skimmer to help, but any recommendations on a great portable vacuum that can be used daily? I’m in the price range for 500-1000$

[@RichardLeblanc-ci3fg]

Really appreciate your very thorough video. I found it after 3 hours of online research and going to my local pool store. I suspected that Maytronics sells identical models with different names through distribution channels at slightly different prices and you confirmed it! Also see that my now broken Pentair Prowler 520 is made by Dolphin so seems like there is not much competition in the robot cleaner market ... all roads lead to Maytronics? Does the pool mapping across the various models really make a difference? With my existing Prowler it seemed to be pretty much random. Do you fix a lot of problems with the power supply? My has needed to be replaced twice in 4 years ... could it just be because it is exposed to rain during the May - Oct pool season?

[@thedolphindoctor]

I find that power supply's are my most common warrantied part. In an effort to lower that number I have suggested to customers to do a few things. 1. do not let it bake in the sun. keep it shaded, especially when running. 2. keep it out of the rain. although its water resistant if it really DOWN pours, water resistance might not cut it. I first suggested the keeping it out of sunlight thing last July and have seen a SIGNIFICANT decrease in power supply warranties. Also keep in mind low grade extension cords and even high grade ones have an effect on the power supply and might effect their longevity and that is why Dolphin will say not to use them. The sunlight tip works because the power supply in its own right is computer, it heats up when on. Adding 90 degree + days on top of that can not be good for it. Can it run in the sun YES. but is it better to run shaded YES. Dolphin is the largest brand by far at this time. You can look at Polaris as I think they are the only legitimate company worth possibly moving too but dolphin still has them beat on most fronts; quality, warranty process, filtration, and simplicity of design being what comes to mind. The dolphin does map the pool out using INFORMATION AND MEASURING. in the most simple way: it measures distances between walls and wall heights to map the pool every time it runs and will clean the pool using that info. It doesn't retain this info in-between cycles otherwise it would need to start in the same exact spot every time. Going with a unit that has 2 drive motors compared to 1 will increase performance since it does more laps around the pool in the same time. More coverage. They also have a stronger vacuum motor in most cases. that is why the M400 is such a good value this year

[@DeboraGault]

Thank you so much for the video and the great information. I have a 24' round above ground pool - I have been using a very old model with a bag and I'm thrilled that I can upgrade to a basket design which is so much easier to use and clean. My needs include a large number of cleaning cycles upon opening but I keep on top of the pool when it's clean and will likely only run the unit once per week. I ordered two E10 models from Amazon which I need to return because both short circuited within a few days. I need some guidance as to what model would be best for me to purchase. I was talked into a Liberty 200 at a pool store today and after viewing your video, I'm planning on returning it in the box without even trying it out. Can you please help me with your recommendation as to what model I should buy. Your help would be much appreciated. Thanks so much.

[@thedolphindoctor]

if you aim for 1 time a week I think an S200 is the safer option for that size above ground. But I also think its possible to get away with an E20. You might need to run that more than 1 time a week though. even though the pool is clean its good to have it run just to brush the walls and floor to disrupt algae growth.

[@DarrenWeaver-h5i]

I have a 47x24 free form pool with white plaster. There are multiple levels- it goes from 3.5' to 8.5' and there are no real straight edges along the bottom (not squared off like some rectangular pools). We tried the beatbot aqua sense pro (the "alleged/supposed" absolute best of the best in cordless) but it failed fairly significantly leaving wide and long swaths of dirt after almost 4 hours in their custom beta mode (which was supposed to correct the issue). Is the problem my pool? I love this video and the advice on corded vs cordless-- I've been swayed back to corded and will be trying the M600 or active 60 unless you feel that no auto/robot type vacs will give me at least 90-95% cleaning on the floor. Let me know- I've looked everywhere but all reviews are being funded now and very few are from non-influencers so I absolutely appreciate this series. Let me know please.

[@thedolphindoctor]

You are in the same boat as a lot of people with the beat bot. Most reviews and articles are paid for. Bad reviews are censored. I see it every year with brands that come and go. No cleaner will advertise 100% of your pool but usually the realistic goal is 95 to 99% If I'm imagining the floor to wall transition in my mind correctly you should be fine. Non hard angles are better than hard angle transition from floor to wall. As long as you take advantage of the different cycle options I think you'll be satisfied. Make sure you make use of the floor only mode when the pool is dirty. Might take a few cycles to get any pool clean depending on how bad it is. You just need to find out how often you need to run it every week to have it not get so bad where one cycle isn't enough You should put an honest review on the beat bot and see if it's deleted or ever posted. I would make your opinion known on the facebooks pages or reddit if you want other people to see through the lies

[@meanmachinesrcclub]

Hey! Thanks for a very comprehensive and illuminating video! I have a question. If I buy the S300 and connect it to the control unit of the S300i, will that enable these features from the S300i on the S300? Backstory: I have an S300i, which (according to service) has the drive motor broken) I now only have the choice of buying an S300 (not i) which has less features than my old S300i! For instance, S300 has no weekly schedule and max 2 hours vs S300i with weekly schedule and also 2.5 hours cleaning time! My other option is M400 supreme! I am inclined to this, but It would be interesting if the S300 will be “unlocked by the contro unit of the S300i and benefit from its features . Thank you!

[@thedolphindoctor]

The newer s300 is WIFI based so i dont believe the controls of the 300i will work on it since it was bluetooth based. You can also look at the S400 as that is what replaced the S300i in the line up

[@meanmachinesrcclub]

@@thedolphindoctor The S300I was wifi enabled (as well as bluetooth enabled)! I have used all features for 3 years now:) Basically connected to the cloud so I could start it over the internet as well! The old S300 (not “i”) was the one that was only Bluetooth enabled! So basically I have a fully working wifi enabled control unit from the S300i, with werkly scheduling and 1.5,2,2.5 hour cycle, and all combos of floor, walls and waterline cleaning, and the question is will this control unit work on the new S300 unit that also has wifi, but no weekly scheduling?

[@JT-gy8pj]

Hi appreciate the great review and explaining things out in simply layman terms. Which one is these corded Dolphins is comparable to Polaris P965IQ? What's your thoughts on the Polaris P 965 IQ compared to a similar Dolphin?

[@thedolphindoctor]

closest in terms of specs would be either M400 or M600 but the design is pretty different from what polaris has going on with the big wheels. I find that polaris often has over complicated designs with more parts that become a pain to work on. They also lack the filtration quality that the Dolphins have. Dolphin is often a bit more $$$ but the quality of parts is also higher compared to what Polaris uses in my opinion

[@MS-co3pu]

I have a M400. Sometimes has trouble getting to water line. Also what position do I put the handle and do I put the counter block on handle out? Need some advice. Thanks so much!!! Great video!

[@thedolphindoctor]

you want the handle diagonal across the body. is trouble climbing brush the walls manually one more time. have floats extended all the way out

[@JoelEpperson-mb6zy]

This was truly one of the best video's I've seen in comparing in a practical way all of the 2024 lineup for Dolphin. As a result, i bought the Nautilus Supreme from Pelicanshops and hope to be able to come back and let you know how well it works. I had a Polaris P825 that i bought in 2017, never had an issue, but the controller went out so i decided to buy a new pool robot, we'll see how well these compare...thanks again for the great info!

[@thedolphindoctor]

I'm glad my video helped! I think you will be happy! Be sure to check out my Do's and Don'ts Video to help make the cleaner last a long life

[@ulianasavchii9755]

Thank you for your detailed video, but I still undecide which one right for me. Could you recommend the top pool cleaner from both the Standard and Deluxe categories and explain why you prefer it? In ground big plaster pool,27 000 gallons Please don't recommend the most expensive vacuum cleaner just to sell a pricier one. Please recommend the one you would choose for yourself and wouldn't discord in a year or two. Bluetooth and the warranty are important 24 or 36 month, but the most important factor is the effectiveness of the cleaner.

[@thedolphindoctor]

For your situation and the range you gave me S200, S300, or M400. S200 is the cheapest I would go as you still get the rebates on it and it will do waterline scrubbing, come with both filter types, and its the basket design S300 same as S200 but with WIFI, floor only mode which comes in handy, and The caddy included M400 if you want the longer warranty and overall a stronger unit that doesnt need to run as much as the S200, S300 since its faster and stronger. only down side is its not the basket design like the S200, S300. IF you want the best of both worlds that's when you consider M600.

[@kevinspiteri9590]

Great and very detailed! Can the M600 handle tanning shelves that is around 8 inches below water level?

[@thedolphindoctor]

Unfortunately no. It's not deep enough. Those areas will need to be brushed off manually into the main pool area

[@DL401175]

Thank you for taking the time to make this video.

[@thedolphindoctor]

My pleasure!

[@RoseC-ec4et]

Thanks for the video and explaining all the different models, it definitely got confusing and overwhelming! So we currently have an oval 15x27 semi inground pool and need to get a pool robot. We're considering the M600 or Active 60, can you tell me which you recommend and if either will work with (is recommended for) our pool? Thanks!

[@thedolphindoctor]

M600 or active 60 will be the same unit other than color and name however I Would go M600 as the blue over time will fade to a lighter blue. active 60 will yellow out over time. its purely cosmetic though

[@RoseC-ec4et]

@@thedolphindoctor thanks for the response. And this will work for our aquasport semi-in ground pool (vinyl liner) - walls and waterline included?

[@thedolphindoctor]

@@RoseC-ec4et I would think so

[@patrickyoung5781]

Hello! I have a 2011 Nautilus that all of a sudden only goes forward in full speed. Never reverse. Is there a factory reset to fix this?

[@thedolphindoctor]

Unfortunately no. Technically the robot is reset whenever you turn it on. Most likely there is a motor issue

[@1027Paula]

Holy Cow! Notes all over the place. Now to decipher what I wrote and what it all means. Your recommendation for a 16x32 in ground vinyl pool??. I would def. like to have the fine filter as I get alage from what I believe is because the pool doesn't get used enough. I always felt a clean pool is a used pool. Hoping a good cleaning with one of these will do the trick. So fine filter is a must, top loading for ease, water line cleaner and perhaps active cleaner brush would be nice. (how would you rate the importance of those 4 features that I like? )Oh another consideration, i have brick set in sand around the pool so I do get some sand in the pool. No trees in the area so no leaves. Is a caddy necessary? I'm not sure how heavy these are to pull out of the water. Which model or two would you recommend? I wouldn't mind paying a little more IF a rebate brings it down in price to match a lower model without a rebate. You're in NJ, I am on Long Island. I assume you would ship? One last mention, if it only comes with a "fine" filter, can I purchase an Ultra fine filter and if so, how much?

[@thedolphindoctor]

All the features you mentioned are important to consider. especially the active brush that a lot of sites overlook (because their models don't have them). The M400 is one of the best values across the board and have everything you want. The M600 would be a step up with the more convenient basket design. Caddy helps you keep the cable neat and it helps you move the robot to where you want to store it. otherwise you have to pick it up and it hard not to get soaked as the water will drain all over you as they are a bit awkward to hold. Both of those models have rebates through dolphin and pelicanshops1.com would ship there!

[@rmika99]

Great and comprehensive video! Waiting for the Liberty 400 to hit shelves.

[@thedolphindoctor]

Pelican should have them within this week or next

[@frenchyf1568]

Great video! I had the Triton PS since the summer of 2017 and last season it finally went dead on me. A few weeks ago I ordered the Proteus DX3 to try that one out. Weirdest thing but one of the tracks fell off while vacuuming. Also, one of the rubber sweepers on the bottom kept falling off during every cycle. Anyways, I returned the Lemon and ordered the Triton PS again. The only question is I have is that the new Triton has this white tube like piece that connects the end of the power supply to the cable that was not on the original model I got in 2017. Do you know that that is?

[@thedolphindoctor]

In the cable itself? Do you mean the cable detangler?

[@frenchyf1568]

@@thedolphindoctor Yeh in the cable towards the top where it connects to the power supply. Is that the detangler?

[@christineortino4463]

GREAT video 🎉 helped me make my decision. Will be calling to order the M400 ❤

[@thedolphindoctor]

glad it helped!

[@Jmcgrath7]

Hello from Upstate New York. Wife and I got our first inground pool last fall and are now in the market for a vacuum. Our pool is salt, 16x36, and is in large open space with no trees and will not have much foot traffic for the most part (just the wife and I). Do you think the Liberty 200 would do the job? I like the idea of going cordless and having to charge it before every use is not an issue. Thanks!

[@Jmcgrath7]

Or is the extra $200 for the ultra fine filters the way to go?

[@thedolphindoctor]

for an inground pool the liberty 200 wont perform at the same level a corded would at this point. the 1.5 hour cycle time is going to lead to the pool not being cleaned as much as a 2 or 2.5 hour cycle. The Liberty 400 which is eventually..... coming this year (keeps getting delayed) will be the full fledged in ground cordless from dolphin, having a 2.5 hour cycle time and water line cleaning. I would definitely stick with dolphin either way. Going corded is not bad at all. Cordless has its own downsides at this point that I think outweigh the cord. Liberty 400 will be the exception though!

[@jwalker3521]

Great video! Would you happen to know if the E10 is an appropriate vacuum for a 10,000 gallon round above ground Intex pool? Or would it be overkill?

[@thedolphindoctor]

it would be fine. it would only do the floor and lower walls

[@jwalker3521]

@@thedolphindoctor would it be okay to leave in the pool? (Only take out to empty the basket and when we are swimming)

[@jkozas]

​@@jwalker3521I wouldn't recommend it. It won't last as long if you take it out

[@ozzielara2337]

I’m really happy I found this comparison. My suction side cleaner (Pentair Rebel) is officially at the end of its life cycle and I’ve been considering switching to a robotic cleaner. I was looking at the Nautilus CC due to the obvious price point and recommendations of people on some blogs. I’m not so sure if that’s the best value for my pool now. Such a tough decision because I really don’t want to spend $1200 on a pool cleaner either especially when I can replace my current cleaner for $400. Can you provide a video on potential maintenance costs on these robotic cleaners? Like am I going to expect to pay $300 dollars every time something breaks? That would definitely be a deciding factor on whether I want to make the switch. I should also mention that my pool is open year round (South Florida) and have a very large black olive tree that dumps a ton of leaves in my pool.

[@thedolphindoctor]

I would say yes and no to your question. usually only 3 things go bad on these things... motor, cable, power box. But if you TAKE CARE OF THEM and avoid he common mistakes people make, take it out often and dont leave it in the pool to get corroded by long term high chlorine exposure or pH reducer chems you should have a long life of AT LEAST 5 years before that happens. pulling on cord to strongly, not keeping power box out of shade are also things I would avoid doing. THE MORE its in the pool the more parts will break which means more maintenance. suction side cleaners are constantly needing yearly maintenance to replace belts, wheels, bearing because they are constantly in the pool which means almost a yearly cost to maintain it. usually with a dolphin IF MAINTAINED PROPERLY should not need that BUT when it does need work it can be pricey. depending on the model though you might be able to repair it on your own to save on labor or bench fees which can work out!

[@Norm6671]

This was very helpful. Thanks!

[@thedolphindoctor]

Thank you!

[@tonymattei169]

Great review, very helpful. One question on the ultra-fine filters. Do they put undo/additional strain on impeller motor reducing lifespan?

[@thedolphindoctor]

no particular strain. but the motor considers the filter full when the strain increases so when the thicker filters are in it tends to consider itself full quicker when cleaning a really dirty pool. you want to just make sure you use fine filters as much as possible when the pool is dirty and then when the pool is pretty much clean swap to the ultra fine filters. its always a trade off. the thicker filters are great for filtering but suction power goes down to support that. fine filters allow higher suction power but less filtration. Still, most of the time you will be using ultra fine filters

[@tonymattei169]

@@thedolphindoctor Thank you very much for the prompt and precise reply. Appreciate it.

[@RhondaRudicel]

When deciding between a cartridge filter or basket filter, what criteria should I consider other than size of debris I find typically in my pool?

[@thedolphindoctor]

convenience would be one as it'll probably take you 30 seconds to a minute to clean out a basket vs 2-4 minutes with two cartridges. basket design has less parts overall compared to a cartridge design and they are easier for you the customer to maintain for example track and brush replacements are easier on a basket design. however the cartridge's deisgn is a little bit more efficient getting leaves as there is two entrances for large debris vs one on the basket.

[@mattpitzer5566]

Looking at the chart, what is the difference between basket and dual layer basket? If it just says basket, does that mean you have to switch between the filters depending on what you need while the dual layer has both filters in at the same time?

[@thedolphindoctor]

you still have to swap but the dual layer basket comes with an additional insert that goes inside the basket to add another layer of filter

[@jomunjr]

I notice the M400 and M600 do not have nanofilters as an option, they do have ultra-fine filters though. How significant do you think this is, or is it a marketing gimmick? In what scenario is having a nano filter a good thing? The Sigma does have a nano filter. I also read about one supposed customer having a Sigma get stuck on the drain and Maytronics took it in and added an active brush. Is this correct?

[@thedolphindoctor]

It's a marketing gimmick. I mention in the video nano filters specifically. Some sellers change the wording and make it seem like only the ones on their site have it..... Ultra fine filters (what dolphin calls it,) = what the misleading sellers call nano filters. Maytronics wouldn't take it. The seller would've had to do that.

[@AlexaBabula]

Hi, thanks for the video. My pool is overflow, 6x12 meters. No leaves no debris in the pool. only problem is dirt in the bottom of the pool. Iam between M400 , M600 , M550 and M700 . In addition which filter is better for dirt.. fine filters or ultra fine filters?. Please suggest. Thanks :)

[@thedolphindoctor]

with dirt, try to see what fine filters will get. then go ultra fine. you don't want to overload the ultra fine filters with too much dirt. M550 and M700 are not available in US. but M550 seems like a good value.

[@AlexaBabula]

@@thedolphindoctor Thanks a lot :)

[@RandySolomon-wm5jg]

Great video and glad I watched this (I watched last years as well)as u make it easy to navigate all the models so thank you! Just curious if you can say which store in NJ u work at? I’m about to pull the trigger on a unit and would like to personally say thanks if the store is close.

[@thedolphindoctor]

The website the chart is on and the location I work at is the Morris plains NJ location. The other locations are independently owned and do not have the same inventory or pricing unfortunately

[@CptJoshami]

Hi! Im trying to understand where the premium lineup goes in the columns. For exemple, is the premium 30 equivalent to the active 20 column but longer cord and the premium 40 is with the active 30? Ps : Amazing video! Such a nice condensed version of every usefull information. Definitely makes me want to go see in store and not just online 👍

[@thedolphindoctor]

Premium 20 is the same as active 20, 30 same active 30 etc. cords same length

[@CryptoNut82]

Great video, thanks for all the work you put into this

[@thedolphindoctor]

My pleasure!

[@jay446944]

My old Dolphin that used a bottom loading bag filter finally crapped out. I'm on an extreme budget. My most essential need is ultra fine filter that cleans the bottom of the pool. Do you have a recommendation?

[@thedolphindoctor]

depends on how extreme. you can get away with an E20 at $599 and put the ultra fine filter basket seperately for $80-100 and get away under $700. or you can go with an S200 at $1099 that comes with the filters and also the $100 rebate...... both units will clean the pool as long as you run them enough to keep up. they are more PREVENTATIVE and excel as keeping the pool clean if you run them consistently (3-5 days a week) both will still take numerous cycles to clean an already filthy pool.

[@jay446944]

@@thedolphindoctor Thanks for the advice. So the E20 and the other $499 models are all the same. I don't get why all pool robots don't come with at least the option to purchase ultra fine filters like Dolphin does. I had my pool filter pump and robot cleaner break at the same time this spring so my pool budge is stretched thin. I have solar panels so running it all the time is not a problem. I live near farms and river with a strong delta breeze in California. I need to get the ultra fines that can collect when its windy. I think both recommendations will do at least as good as my 20 year old Dolphin did. And it did well.

[@miketaylor5393]

Great video. You just cleared up a huge amount of confusion I've had with all the different Dolphin models. Subscribed Can you please tell me if any of these models will clean the wall and waterline above a pool bench? This is important to me because 65% of my pool walls have a bench which renders most robots with waterline cleaning useless in those areas. The only video reviews I've seen for robots that do the walls and waterline above a bench is the Beatbot Aquasense Pro but I haven't seen a review of what happens with any Dolphin in bench areas. Issue being the Aquasense is brand new and there is no way to see how well they hold up or are supported yet vs. Dolphin which has solid support.

[@thedolphindoctor]

It depends on the bench can you get me dimensions of the bench. How deep is it from the waterline, how deep is the seat from the edge of it to the wall? Basically we need to see if the dolphin will fit on the whole bench and be submerged enough so it can get a footing on the bench itself and then to initiate the climb to the waterline after that. Its a tough call for sure

[@miketaylor5393]

My benches are 16" wide (edge to wall) and 20" below the waterline @@thedolphindoctor

[@yehudagoldberg6400]

Thanks! Im gonna be calling your store and ordering one later today!

[@JeanneWalker-r2g]

I am a 79 year old female who takes care of my own pool. My pool is L shaped 30x10 and 22x12 (deep end) I am looking at the Liberty 400. I do not want anything with cords or hoses. I am looking to get a little lazier with pool upkeep. My pool is completely caged so it has little to no debris except in hurricanes. I'm not concerned with run time, my main concern is the shape of the pool. will the Liberty 400 handle the rounded corners and the slant to the 8' depth?

[@thedolphindoctor]

going cordless is easier because of no cord but its not as strong and does not run as long. so. you need to run it more to clean the pool which means more in and out and charging it. for that size pool it just wont cut it in my opinion. not in one cycle.

[@strahle8758]

Great video. Thanks for putting in the effort. I have owned the M400 for a few years now. The insulation has broke in a couple of places on the cord. I was thinking about replacing the unit, but now I think I will just replace the cord since this still seems to be a good unit on the market.

[@thedolphindoctor]

Glad it helped. if it has only been a few years definitely do cable replacement.

[@copycatcraftsbyjill3008]

Love your videos. Question, i own a nautilus cc 99996113-us. It works great but it needs a new communication cord. Can i buy a upgraded cord with a swivel so the cord does not tangle up all the time. If so, what is the part number? Thanks for any help

[@thedolphindoctor]

99958907-DIY should work.

[@copycatcraftsbyjill3008]

@@thedolphindoctor thank you so much.

[@ecstasyj]

Hello, i’ve watched your videos and am wondering what your thoughts are on the dolphin s150?

[@thedolphindoctor]

Hello. It's not a US cleaner but from what I understand about the Australian S150 is is has the same specs of the s200 but instead of separate filter options it has the "dual filtration" basket similar to what the s400 has here in the US. I'm not 100% sure though. If your in Australia I would reach out to Sydney pool robotics to get more accurate info as they are on a lot of forums I'm on and seem to be a good hearted company based on how they try to help people similar to me in the US.

[@Wannaloom]

So is the M600 and Active 60 identical? Trying to decide which to go with. If I order from y’all and have an issue do I send back to you for repair work? How does that work?

[@thedolphindoctor]

M600 and active 60 are the same other than color. M600 is the more popular of the two and I recommend that one due to the color fading to light blue vs white going to yellow. Pelican covers shipping back and forth up to 2 times for warranty claims. labor is always covered and parts are covered under maytronics. You would just contact via phone or email to get that process started

[@Wannaloom]

@@thedolphindoctor ok, great thank you!

[@Sugarcuddles1]

I own a hotel and live near a black sand beach, people will jump in the pool and get sand on the bottom all the time... Out of these vacuums what do you recommend would be best for that? I plan to run it at night so that in the morning it is clean and ready for guests to use.

[@thedolphindoctor]

depends on how large the pool is. if it is within 50 feet you can stay within the "residential" category of dolphins, which is everything covered in this video. However I would still go heavier duty due to how much it would be used. Since you said sand would be an issue I would also say go with one that has less parts overall. The sane will wear down the parts faster as it gets in the units inner workings and slowly sands them down. You will want to be vigilant in hosing off all the nooks and crannies to dislodge as much as you can. My reccomendation would be the M600 but if you want a lower cost go M400 but keep in mind is has more parts. I do not think any single drive unit (premier, s200, s300 etc) would be a good option as they will have to run a lot more to keep a busy pool clean. you need to be efficient as possible. I think M600 set to the extended cycle option of 2.5 hours would be great. you can even set it to do floor only if needed to really focus on the sand.

[@Sugarcuddles1]

@@thedolphindoctor awesome thank you for your response! The only thing is I need to order the vacuum online since I live outside of USA… I believe the M600 is only pickup from stores? I usually order everything off Amazon, in that case would you recommend the E70? Also our pools aren’t that big, but sometimes there is an excessive amount of sand in them. The filter on the E70 would be able to hold a good bit of sand? Or would I need to constantly take it out, clean it then put it back in?

[@thedolphindoctor]

@@Sugarcuddles1 where are you located? you just have to make sure the warranty isnt voided by being outside the USA.

[@Sugarcuddles1]

@@thedolphindoctorI live in Costa Rica, but I don't care too much about the warranty. It would be nice but if its voided that's okay.

[@thedolphindoctor]

@@Sugarcuddles1 E70 would be the same as M600 as it is the same robot but with the added thermostat feature

[@SheriMalcolm-p9e]

I just want to confirm - you said you like the cartridge filters better than the basket? so between the M400 and the M600, is it worth $400 more to have a dual layer basket over the cartridge? I realize the M600 also does the floor only cleaning.

[@thedolphindoctor]

Out of the box yes.. but for the units like m600 that have that fine tuning of cleaning settings you will be better off with that if you take advantage of them. M600 does a slightly better job cleaning waterline which I forgot to really mention In video

[@yrefai]

I have a vinyl liner pool and my local pool shop person was telling me the M600 is not a good idea for vinyl pools due to it's powerful suction could pull the liner off. It is only recommended for gunite. She was recommending the S line like the S400 instead. Is this true? I was set on the M600, but now I am concerned. What are your thoughts? Thanks

[@thedolphindoctor]

thats not true. if that were the case there would be warnings all over the place in regard to liner damage. The suction difference between S and M line is only 500 gallons per hour. that nothing. not enough to make a difference

[@Toxic_doc]

Very curious how this cordless Beatbot compares with these dolphins cleaners

[@thedolphindoctor]

@orlyaccount from what I have heard from customers who have tried the beatbot they are not satisfied and return it. specifically with the mapping and the waterline. Various people have stated that they don't live up to all the advertising it claims it does "borderline false advertising" is what I have heard twice now. I have seen this before. where a new company comes along, pays $$$$$! in advertising and sponsored videos as well as good review blasting. And then once people get the product they do not like it and the support ends up being a run around. be careful about what they claim. 9 motors seems way to unrealistic as well especially is dolphins cordless only has 2..... no way that is possible. My biggest warning is dont trust all these good reviews. I would consider the bad reviews I don't think a lot of them are genuine.

[@derekg3035]

Not sure which direction to take. Could you weigh in? Looking for a cordless cleaner for a 32,000 gallon kidney-shaped pool. Down to Aiper S1 Pro, Dolphin Liberty 400, or Polaris Freedom (or any other if you recommend something else). Any thoughts?

[@thedolphindoctor]

Liberty's will be getting a 2.5 hour run time soon. I would say liberty 300 in a few weeks when they start hitting shelves. Liberty 400 won't have 2.5 hour until next year

[@sebastienviaud1511]

Can you comment on the new M550 compare to M600 please ? And what is advantage of 3 motors instead of one ? I have pool with ceramic 12x6M . Thanks for video that clear my mind about the range

[@thedolphindoctor]

M550 is not out in US yet but its essentially an M600 without all the customization options etc. It will be included in next years video when it hits shelves here in US

[@KrazeeG]

is it OK to leave your cleaner in the pool? If not, why do they have the 3 options for restart.

[@thedolphindoctor]

A common question often brought up by customers for sure! Here is my take: (be sure to read the 2nd paragraph as it adds some context!) My viewpoint is that the scheduling is a double edged sword, although convenient its not the best for your cleaner as its in the pool most of the time. It also depends on how much you need to use the pool vacuum. Some pools only need it 1 or 2 times a week, some need more. So if your only using it 1 or 2 times there is really no need to use the scheduling feature in my opinion as the benefits of taking it out and potentially getting years more in life far outweigh the benefits of the scheduler. This is common debate amongst any automatic pool vacuum owner. On one hand you have the argument of “well it made for the pool it should be in the pool”. This is a common viewpoint some people have, especially if they are coming from a suction side pool cleaner which was ALWAYS in the pool. This argument makes sense if you don’t account for anything else. The biggest Killer of automatic pool cleaners is long exposure to chlorine (ESPECIALLY HIGH LEVELS OF CHLORINE). The longer its in it the longer it has time to eat at your vacuum. It causes a tangling cord and it slowly dries out the o rings that keep the water out of the important spots like the motor and the cable detangler. So, when you take into account these facts, the argument of “it is made to be in the pool it should be in the pool” falls apart. It might be made for water but its not designed to withstand chlorine all the time. I’ve seen cleaners that are only a year old come back looking like they are 10 years old and I’ve seen the opposite. So, on the other hand, my suggestion is, take it out when not in use OR at the very least take it out when you shock the pool. So, for example, if you shock the pool (or super chlorinate it if you have a salt generator) on a Sunday night then leave the pool vacuum out until Tuesday night. Giving that high chlorine level to come back down to normal levels. DOLPHIN suggest to only run their robots in chlorine levels lower than 4ppm.

[@slayerkspuma]

Great video! Have you looked into the Premium 20 40 and 60 models?

[@thedolphindoctor]

Yes. They are primarily in CANADA however there are a few sources of them in US. The correlate to s200, s400, m600. I would encourage you to buy one of those instead since parts (like the colored shells and side plates) in the US might be harder to come by down the line compared to the main US lines. However you might not ever need to replace them of course.

[@slayerkspuma]

​@@thedolphindoctor Thanks! I'm located in Canada so I guess there shouldn't be a concern with parts here then?

[@Amitbhatia1]

E70 all the way!! Thanks for the help.

[@thedolphindoctor]

Good choice!

[@sandyalias9141]

Hi! This was such a great & informational video. Thank you so much. We live in south florida and we have a small outdoor salt water pool 12x18 (I believe) roughly 6ft deep, figure 8 style with large shallow entry step. We get a lot of leaves/bugs/dirt/ other debris that collects throught the pool and the entry steps. We have someone who comes to clean the pool weekly but it gets dirty after 1 or 2 days anyways. The only thing I know to do is use some elbow greese and go in with a pool skimmer pole and get as much as i can. I dont know what else to do to clean the walls or floors and so we know we will need a robot cleaner to help keep it maintained. I also dont know where to find the hose to plug in a corded vaccum if we chose that style. Anyways, After your video I was debating between Liberty 400 or S300. We would love some of your expert feedback!

[@thedolphindoctor]

I'm partial to Corded until the batter life can improve. Liberty 400 will be a solid option but not until it gets 2.5 hour cleaning time which probably wont be until next season (I know video states it does but it has since been changed and is noted in the pinned comment.). For that size pool either will do. Not sure how it will do on the entry step however. you want to make sure the robot is fully submerged with at least 6 inches of water above it to supply a decent vacuum effect.

[@sandyalias9141]

@thedolphindoctor thank you so much for responding! I do not believe there will be 6 inches above the vaccum to be able to clean the entry step, it's probably only about 3 inches of water or so. What do you suggest to clean that entry step? Also, there are a few areas which have a protruding rock style waterline and then tranition to flat tile, would these vaccums clean this too? Besides the s300 or liberty 400, would you recommend any other models for our pool? Or based on the size do you think the run time on the liberty 400 right now is plenty enough? Also, I feel much more comfortable ordering from a reputable location and your shop gives me come peace of mind especially with you there. Online says the liberty 400 is sold out there though. Should I keep waiting for the one that has the 2.5 hr battery life?

[@sandyalias9141]

@@thedolphindoctor hi! Just touching base from my last reply 😀

[@thedolphindoctor]

@@sandyalias9141 I will respond to each question below I do not believe there will be 6 inches above the vaccum to be able to clean the entry step, it's probably only about 3 inches of water or so. What do you suggest to clean that entry step? - The steps will have to be brushed off manually into the pool area where the cleaner can get the debris more efficiently. This is the common process with all steps as no robot (unless the steps are unusually large) can fit on each individual step and get a vacuum seal. Also, there are a few areas which have a protruding rock style waterline and then tranition to flat tile, would these vaccums clean this too? - Most likely not as the rock will cause it to fall backwards if it can climb onto it. Most likely will need to be brushed in those spots instead Besides the s300 or liberty 400, would you recommend any other models for our pool? Or based on the size do you think the run time on the liberty 400 right now is plenty enough? - If you have a ton of debris I would suggest a 3 motor unit compared to 2. The Liberty 400 (gen 1) which will come out this month will still only have a 1.5 hour time. I do not think in your situation this is enough. I think the S300 is the safer bet Also, I feel much more comfortable ordering from a reputable location and your shop gives me come peace of mind especially with you there. Online says the liberty 400 is sold out there though. -Pelican will be getting them in this week or next.

[@HoleShotPhotos]

I have a Nautilus CC Plus. Actually have 2 of them when one of the power supplies was acting up I bought a second one. There's 2 main performance issues I have with it and i'm looking to upgrade. I already have a CADDY so I don't need that. My CC Plus almost always get stuck on my steps. It's really annoying. And the second issue is i'm having a hard time keeping the pool clean. I have the FINE and ULTRA fine filters. I always keep the ultra fine filters in it. But i can literally see the dirt on the floor, it'll roll over it, pick it up, and i'll see the pump spit it back out the top. I've checked the filters and they don't have any holes in them. Any suggestions what I should upgrade to? Any will any of the other units use the same power supply that I currently have since i have 2 of them?

[@thedolphindoctor]

some units have a dual layer filter in addition to the other filter types in the basket / cartridge. this might help your situation. the CC plus is known to get stuck on steps due to the weight distribution within the cleaner. Usually raising or lowering the waterline will help. Either that little bit of extra buoyancy will help it not get stuck. or lowering it a little will make it not get up there in the first place. Not sure what would be getting through the ultra fine filters though. You can try moving to a basket design to see if that helps. or an M400 for an upgrade of what you already have but without the weight distribution issues I mentioned earlier.

[@mikepeckford9776]

We have a 40 ft long pool. Was going to get the premium 20 but the website says “ideal pool length up to 33 ft”. In your video you say these models are good up to 50 ft pools. Any advice on if a cleaner with a 50ft cable can clean a 40 ft pool? Thanks

[@thedolphindoctor]

I do not have the premium line on this chart as its primarily only in Canada. you might be confusing it with the PREMIER which is on this chart and in the video. I would go off dolphins recommendation as the premium 20 will have a smaller basket and it would probably fill before being done. although the cord is 50 ft. you have to account for the depth of the pool as well! you might be able to pull it off but it would probably leave some room to be desired over an S200

[@AlainMorais]

Thank you for this very helpful video 👍Cheers from France 🥖

[@SheriMalcolm-p9e]

Me again! I have now watched this video 5 times 🙂I have down to the CC Supreme, the M400, and the M600. Pool is IG, 10,600 gallons, Salt, and concrete, with a pool cage. We are having a hard time choosing. We do not need bells and whistles, but definitely want the 3 drives, which all 3 of these units have. Is the M600 worth the $400 increase in price? We don't need a caddy, so I am stuck trying to decide. We do want it to clean without having to run it multiple times. Most of our issues are dirt from rain, and maybe some bugs on the bottom, also from rain. We really don't get much debris. Help!

[@thedolphindoctor]

cc supreme is a solid option without a caddy if you do not want it. The floor only mode does come in clutch sometimes. M600 is still worth it regardless of the bells and whistles for the convenience, less parts, and it is a much stronger waterline cleaner. CC supreme is still solid value though.

[@DizzyDungeoneer]

Great video. One suggestion for improvement: include metric equivalents for those of us who don't speak freedom units.

[@shanewilliams3520]

Great video, I notice the Sigma advertising boasts the gyroscope a lot and you did not bring it up in your review. is it meaningless advertising? I ask b/c the CC Supreme has just dropped 200 below the Sigma making it a no brainer according to your review. Is the gyroscope something all models have?

[@thedolphindoctor]

All dolphins have that sensor in them. It's marketing.

[@shanewilliams3520]

@@thedolphindoctor thank you, one more question, is it safe to "gently" pull my robot "close" to the surface by the cord? obviously I don't want to yank it or drag it out of the water by the cord but is a gentle tug ok?

[@vickj1286]

Which one you recommend between m400 or m600 15’ by 30’. 6ft deeper end pool.

[@thedolphindoctor]

Either one but M600 will be easier to clean out, It will do a better job cleaning the waterline, has less parts overall, and has two important features that might seem like a "bell and whistle" feature. FLOOR ONLY and the PICK UP MODE. both these features come in handy. FLOOR ONLY to focus on the floor where the debris is. so the robot doesn't get distracted with the walls when your just trying to vacuum debris out. and PICK UP MODE so you don't pull on the cord to take the robot out of the pool. this will cause the robots cord to last longer so no possibly breaks happen at the detangler part of the cable from the pressure of pulling on it. M600s basket design will be a lot easier to clean out as well compared to the cartridges. M400 is still a slightly better value in terms of specs and bang for your buck but if you value convenience M600 is a better value at that point

[@SusanKolozsvari]

Very helpful! Thank you for putting this together!

[@thedolphindoctor]

You're very welcome!

[@HB-bc5it]

What’s the current pricing on an m400? Any rebates? Thanks

[@thedolphindoctor]

Current pricing is $1499. There is a manufacturer rebate on it for $100 until August 31st

[@gilbertgrenier4896]

Here in Canada we have the Premium 40 and Premium 60. Would I be right to assume they compare to the S400 and M600?

[@thedolphindoctor]

from what I understand that is correct!

[@markgoldberg1231]

Does anyone know the difference between the standard clean and the ultra clean on the M600 They both seem very similar? Both clean floor , wall and water line both work for up to 2.5 hours Thanks Msrk

[@FixItWithMe]

How do u remove yellow stains from a white plaster pool WALL? Can u use this also on the wall to just the floors?

[@thedolphindoctor]

If it's staining I would probably try a stain remover. You probably have hard water if your getting yellow stains. Not sure how effective a cleaner would be on heavy staining like that

[@JustAGirlyGeek]

Which robot would you recommend for a 27 foot round above ground pool?

[@thedolphindoctor]

E20 or S200

[@frankrizzo7351]

What happened to the weekly timer for the nautilus CC? They changed to a basic single button power supply. I ordered from dolphin expecting the timer power supply. A bit upset about this.

[@thedolphindoctor]

what cc did you get? just the "cc"? cc plus with wifi? cc pro? My understanding is that JUST the "cc" model and "cc plus without wifi" would have the "123" button for scheduling. The others must be done through WIFI. Keep in mind dolphin does not sell direct even on amazon etc its just a dealer/reseller you can probably reach out to the seller and ask.

[@TeresaChapman-bw1fu]

I have inquired from my local pool store about the Active30 but I just wanted your opinion on it for a 40 foot long fiberglass pool with a toe ledge all the way around it? Will it do a sufficient job climbing the walls and cleaning the waterline?

[@thedolphindoctor]

It should be able to get over the hump of the toe ledge. The motor being situated towards the front of that model keep it from falling backwards on those types of ledges, instead it usually falls towards the inner wall after the ledge. Just keep in mind if the robot can't fully fit on the ledge it might not get the best suction to vacuum the actual ledge.

[@TeresaChapman-bw1fu]

Thank you so much! I’m in Cincinnati. Our local store doesn’t do service. If I call your store and order from you guys could I ship it to you for service? I’d love to purchase from you!

[@thedolphindoctor]

@@TeresaChapman-bw1fu yes pelican will do that for sure. They cover the shipping.

[@lauriegereaue1561]

Hello, we have a 12'x35' (3feet to 6feet depth) inground pool whose pop up system is not working properly. About 1/3 of the pop ups do not pop up & there are bubbles coming out of the ones that do pop up. I was told that it would cost a lot to change out the pop ups & that it may be better to get a pool vacuum. Because the pop ups don't all work, the water does not turn over like it should, it is not pushing the dirt to the drain like it was intended (pool is 20 years old). We were thinking that we would turn off the pop up system and use a vacuum to clean. I take care of the pool and really not interested in cords so I was looking at the cordless models. Since we travel and are not always at home, I didn't want to keep the bot in the pool while we are away. So I was thinking that when we are away we could remove the bot and just use the pop up system with our pool person coming weekly to maintain the levels. With all this being said, we have 2 trains of thought (1) turn off pop up system and get the Liberty 400 or (2)keep the pop up system on and get a less expensive cordless to work along side. What are your thoughts? TIA

[@thedolphindoctor]

thats a tough one. your already putting yourself at a disadvantage with cordless at this point due to the shorter run times. but I would say liberty 400 is your best bet in the cordless realms. I would probably move away from the pop ups.

[@lauriegereaue1561]

@@thedolphindoctor thanks. That's what I thought as well.

[@billcampana2713]

Are there certain models which are better for above ground pools with vinyl liners?

[@thedolphindoctor]

for above grounds I would say anything above an S200 / s300 would be a tad bit overkill for an above ground pool.