Best Floor Jack? $1000 Snap On vs Daytona, Pittsburgh, Arcan, Black Jack, ESCO, Husky, Maasdam

3-Ton Floor Jacks: $1000 Snap On, Daytona, Pittsburgh, Arcan, Black Jack, ESCO, Husky, Maasdam. Jacks tested for maximum lift (3 ton rating), bleed-off under load, rolling resistance while under load, jack handle and jack efficiency under load, handle pressure to lift 3 tons, number of jack strokes to lift vehicle, holding 3,000 pounds for 24 hours, and jack build construction quality. I purchased all of the floor jacks to ensure an unbiased review. So, thank you for supporting the channel.
➡ Thank you for supporting the channel through memberships:
/ @projectfarm
➡ Thank you very much for supporting the channel through Patreon: / projectfarm
➡ An easy way to find past videos along with products tested: bit.ly/2FCrBpk A big thanks to Jim for putting this together.
➡ Merch: project-farm.com
➡ Click here if you'd like to subscribe: / @projectfarm
➡ As an Amazon Associate I earn from qualifying purchases.
➡ Products Tested In This Video (in no particular order):
Black Jack: amzn.to/3SYHrMf
Arcan: amzn.to/3Cb4wp3
Pittsburgh (also available at Harbor Freight): amzn.to/3CfSvPr
ESCO: amzn.to/3Pv1r6r
Husky: amzn.to/3A7QMJk
Maasdam: Available at Home Depot
Daytona DJ3000: Available at Harbor Freight
Snap On: Available at Snap On’s Online Store
Jack Oil: amzn.to/3Pv0iMb
Videography Equipment:
Sony DSC-RX10 III Cyber-shot Digital Still Camera: amzn.to/2YdXvPw
Canon 70D Camera: amzn.to/31b5Gy0
Azden Microphone: amzn.to/34d3DLE
Go Pro Bundle: amzn.to/3Ca0ZVN
This video is only for entertainment purposes. If you rely on the information portrayed in this video, you assume the responsibility for the results. Project Farm LLC

[@greenrefrigerator]

Around the mid 1990's my wife bought me a Sears Craftsman floor jack for Christmas and it wasn't one of those cheap jacks. This was a true professional looking, serious floor jack and I used that thing for years with the two stands that came with it. It was probably one of the best gifts my wife has ever given me, which is what made it so hard to sell in a garage sale after I got sick (Parkinson's) and couldn't maintain our cars anymore. It was just a floor jack but it was very hard seeing that thing roll out of my garage for the last time and into someone else's truck given how useful it had been and who gave it to me. All I can do today is watch videos of other people using these tools but I'll always remember that floor jack.

[@12345diehappy]

I've got a craftsman 3 ton from right around 1990. I think it weighs 3 tons. It's been amazing. I'm getting to the age where I do al;most no car work and it's harder to move around, but I still like it.

[@jtjones4727]

Dang. My dad is in his mid 70's, but he also has Parkinson's. Kind of the same thing, he can't really do too much nowadays. But he taught me everything I know, and he handed me down enough tools to start my own business. I just turned 44 years old, I'm hoping to be able to work until a reasonable retirement age. Here's hoping my body can keep up another 20 years or so, mechanic work seems to be kind of hard on the body.

[@ProjectFarm]

Thanks for sharing.

[@ComputerLearning0]

@@frylockthefryman I'm managing okay but I sure miss being able to work on things myself using the great tools I once had. And yes, the old Craftsman tools had great quality and were backed by a no question warranty. Although some Craftsman tools are still great, so much of it is now made in China for the least cost available and it further saddens me knowing how so many of our (USA) brands have fallen into mediocrity. I remember the green Craftsman floor jacks (mine was silver) and they were well made and built to last, and you didn't have to worry about it failing if maintained properly. They just plain WORKED.

[@bertgrau3934]

@@jtjones4727 You're correct about mechanics having a tough life, try being a diesel mechanic, that's tough, and many times you either need a hoist or forklift to move stuff around. Sometimes it takes muscle to move some things. Still, any kind of mechanics have a hard life

[@dustondoesit3913]

Best channel on KZbin, and I tested that!

[@ProjectFarm]

Wow, thanks!

[@deletdis6173]

Lol

[@PugCuber]

very impressive!

[@kalashnikov1343]

Very impressive!

[@kg0311]

But did you

[@jetdr]

Snap on lost a lawsuit against harbor freight, the Daytona is made in the same Chinese Factory as the snap on, snap on claimed theirs was made in the USA, but claimed the Daytona stole their design, when in fact it was just being made in the same sweatshop!! Snap on who claimed theirs was made in the USA embarrassed dropped the suit!

[@jessuckakepow]

I wonder how many companies do that bcs I’m sure it’s A LOT? Like “Made In the USA” is pretty vague… like what part was made? The concept, design, manufacturing?? There’s a lot that goes into taking a product from concept to customer and w how unregulated companies are when it comes to marketing claims (and so much more) I’m sure if just a certain percentage of it is done in the US they can make the claim. I went down the rabbit hole of the mattress industry when we needed a new one. I ultimately ended up sourcing components myself and made my own (DO RECOMMEND, btw), but the sh*t they pull is mind blowing. There was a video I saw of a dude cannibalizing a Serta (I think) to take the good components and replacing the worn ones, and as he was removing the layers of this queen size mattress and inspecting them he pulled out a yoga mat sized “gel foam layer.” They literally only need to put a dash of a component in to be able to claim it’s a “gel foam mattress.” 🤯😠 Guess that’s what we get for having weak regulations on companies or former board members/CEOS of said companies doing what little regulation there is. 🤷🏻

[@spicytuna62]

Man, the Daytona jack is seriously impressive. It looks like it was made to basically never break. Only other one I'd consider besides the Daytona is the Arcan, mostly for its light weight. But I'm still inclined to the Daytona for all the grease ports. More than just being cheap, that's a jack made to be maintained and cared for, and that's something I really appreciate about it.

[@ProjectFarm]

Thanks for sharing.

[@mongomongo17]

the daytona is a great jack compared to most chinese made ones.only down side is its heavy

[@wildbill23c]

Serviceability is always a huge item to consider that's what keeps something working properly for the long run. I was surprised when I unboxed my Daytona jack a couple years ago that it had grease zerks on the wheels.

[@marvindebot3264]

For a workshop the Daytona is the pick but if you do mobile service the Arcan is the obvious choice.

[@isaacanderson3968]

I have both the Daytona and Arcan. I prefer the Daytona for all my jobs in the garage. But when I do work around town I bring the Arcan because it's light enough to lift in my vehicle.

[@ericswitzer8360]

I bought a Daytona about a year ago based on good online reviews. I promptly came home from Harbor Freight and requested that you do a comparison test of other brands because there were so many other terrible reviews on other jacks. You responded and said thanks for the idea. I was so excited to see this test finally come through. I've never donated to a Patreon before but I absolutely love your work and appreciate seeing you respond to viewer requests! I will definitely be donating to you because these tests are expensive but important for people's safety and spending money wisely. Thank you for taking the time so that we don't have to.

[@ProjectFarm]

You are most welcome!

[@martinedwards4522]

so?...

[@mrclean4743]

@@martinedwards4522 ?

[@martinedwards4522]

@@mrclean4743 i read it as you were looking for a comparison

[@Sanctified_EDC_Gear]

😎👍

[@Samuel-I]

I have a 3 ton Daytona and it’s a well built and reliable tool. A rare gem from Harbor Freight. Great episode 👍🇺🇸

[@ProjectFarm]

Thanks! Thanks for sharing.

[@markmccarty9793]

Yep, only use mine 4-5 times a year, ain't no way I'm paying $750 more!!

[@robs1873]

@@ProjectFarm None of the things you’re testing really even matter. You’re trading it like we only use Jackson a science lab! Why not test every single Jack on every single car and truck. That’s the real difference!

[@UncleKennysPlace]

@@robs1873 Rather odd comment.

[@kevinbialkowski3694]

@@robs1873 Do it man, Ill check it out on your channel

[@treymignon]

I review everything before I buy it. This review was by far the best I've ever watched. Not because of the products reviewed but by the way it's done. This review is fast, no BS and covers everything. Much appreciated and you now have a life long follower/subscriber!👍

[@ProjectFarm]

Thanks so much!

[@kane2440]

what did you think was the best bank for your buck

[@I.am_Groot]

Agreed this was a great video with a ton of info. I got my low profile 3 ton from Harbor Freight on a big sale paid under $100 about 7 years ago. Fit nicely under my Monte Carlo and pops my Jeep off the ground with ease. Unless I get something over 5,000 lbs or start doing suspension work on the regular no need to spend more than $150 on a jack

[@wilburfinnigan2142]

He could slow down the talk, a lot of info to take in rapidly !!!!!!!

[@riograul2043]

The world is a better place with project farm

[@NaveenKumar-oj7xh]

Usually I end up a little surprised in all your tests, but, here I had not doubt that the Daytona and Snap on would come out on top. That being said, I would buy two Daytona Jacks and two set of jacks stands and still have money left over for a lifetime supply of jack oil, instead of buying a Snap on jack.

[@bretb8799]

Your presentation efficiency is second to none. No fluff or wasted time just brass tacks and you present information so succinctly and at great pace that keeps me interested and paying attention. You should give presentation seminars.

[@ProjectFarm]

Thanks!

[@Aggnog]

Practice makes perfect, you can see the improvement over the years.

[@daleburnfart6845]

I always got that wrong brass tacks vs brass tax. I had to look it up and sure enough I am an idiot. I can now check one more thing off my list that makes me an uninformed idiot. Thanks.

[@bretb8799]

@@daleburnfart6845 Ha I can see how you'd think that since everything is taxed!

[@computernerdinside]

@@daleburnfart6845 My friend once used to say "grass tax/tacks" and wondered why I looked puzzled.

[@mbbs2008]

If there is any channel that truly deserves the YT money, ads and recognition it's this one. Thank you for keeping it honest, and putting in soo much effort in each of your videos. People like you are the true "celebrities" and "stars" of th society, in my eyes!

[@ProjectFarm]

Thanks so much!

[@espokane]

This is the one and only channel I have ever even considered becoming a member/supporter. For the wealth of information provided, two, five, or even ten bucks a month is a steal.

[@TheTechAdmin]

"Thank you for keeping it honest". Don't get me wrong when I say this, because I COMPLETELY agree with everything that you said. But their's no way to know for sure that he's keeping things honest. I think he is a very honest person, and DOES test things honestly. All I'm trying to say is, you don't ALWAYS know when you're being fooled. Project Farm is so honest, he would be the first to agree with me on this.

[@JamesNew-jx8kp]

As an average/amateur DIYer, I own a Daytona jack for 3 years and I can say it always worked and I never had any mishaps. Great value for money and after watching this video, I bet the folks at Daytona benchmarked the Snap-On jack and simply copied their best bits and sell it at a fraction of the price. Sucks for Snap-On but great for consumers.

[@ProjectFarm]

Thanks for sharing.

[@brandonzm1122]

Rumor is Sunnex makes the Daytona and Snap On jacks. I have personally had the opportunity to have them both side by side and I have no doubts they have interchangeable parts. I’m talking down to the hardware it looks to be the exact same. At least the Snap On jack i compared to which was a FJ3000 purchased new in 2016 or 17

[@naru7777f7]

I believe snap on tried to sue Daytona years ago but that was dropped when it was found out that snap on was not made in the us but made in China and had the same manufacturer as Daytona

[@rhllnm]

@@naru7777f7 You'd think the lawyers for Snap On would have checked that out first!

[@patriotarborist711]

F snap on

[@spindaug2425]

I don’t have a floor jack nor will I be needing one anytime soon, but this is by far the best informational and educational video I’ve ever seen. This is how tv should be, thank you sir.

[@ProjectFarm]

Thanks and you are welcome!

[@BrianStDenis-pj1tq]

I consider aluminum jacks in their own category. Their lightness is so valuable when loading them in and out of trucks and race car trailers that you really wouldn't consider a steel jack for that purpose. I feel like you could do a comparison of aluminum jacks which would be very valuable to those who need to move their jacks frequently and who wouldn't consider a steel jack.

[@TranceFur]

Good recommendation.

[@randomusermaximuss]

I don't know if there are enough to justify their own test, but it is a significant note. Under the circumstance a jack you can one hand lift is a significant change. I have a rebrand of the Arcan picked specifically for that reason.

[@tommye9057]

lifting my snap on in and out of a tall truck bed is killer

[@benjaminhenry5869]

Idk, I move my Daytona a few times a month in and out of the trunk of my car. Have had it since 2013. It's heavy sure, but I really don't mind. I might care in another 20 years, but from 24 to 33 it's been fine.

[@zebragoboom]

@@benjaminhenry5869 only a few times a month though, if you're doing it multiple times a day...

[@MrTympas]

After watching for years, I'm still floored with the all testing and explaining of everything. The amount of time you put it into your videos is amazing. Watching the production value go up video after video great to see. Great work

[@ProjectFarm]

Thanks!

[@Irishcream216]

You might be floored, but I'm feeling jacked.

[@jfs70ss]

@@Irishcream216 Both your comments are such a 'Let down'....LOL

[@skeetorkiftwon]

@@ProjectFarm snap-on has a lifetime warrantee, worth mentioning.

[@muppetpaster]

It pays bills....

[@tripezius1]

Been using the 3-ton Daytona for many years on my Tundra, Camry, and Elantra. Love it. The low profile is excellent for the Elantra, and the lift height is great for my Tundra. Outstanding jack that I wish I purchased long ago. Love this channel, btw. You stress test in ways that I can't even dream up and I watch every upload.. Keep it up, my man!

[@michaelgonzales6630]

Wow! Great review and I like your style of straight to the point and no BS. I like your fast talking and fast cuts. It makes the video so much easier to watch and get the information I need vs these guys who ramble on and on. Thank you!

[@ProjectFarm]

Thanks and you are welcome!

[@yotarocket]

I bought the yellow Daytona Jack when it first came out (about 6 years ago) and it was only $180 then. It still makes me happy knowing it was money well spent. The height it reaches for taller vehicles makes a world of difference. Absolutely beast of a jack!

[@ProjectFarm]

Thanks for sharing.

[@theoldbigmoose]

I got mine 6 or so years ago too, with a sale at HF... paid about $120... best jack I've had!

[@MrEunderwood]

I just picked up a green one (3 ton super duty) on sale for about $180 after taxes. Glad to see so many positive things affirming the purchase.

[@luismelchor744]

I got mine on sale for about $120 if i remember correctly back in 2019.

[@wingnutx]

The Arcan was $99 at Costco in 2019. Now its' $249. Great jack, btw.

[@PBTophie]

"We'll go over how to know when your jack needs oil, and how to add oil, later in the video." Above and beyond in both his testing and presentation, as well as in his attentiveness. I love this man.

[@ProjectFarm]

Thanks!

[@wobblysauce]

Yep, it is the little things.

[@PBTophie]

@@ProjectFarm No problem. You didn't have to teach us that, but you did anyway. You're a great educator.

[@donjohnson3701]

I bought a harbor freight jack about 30 years ago and another one with and adjustable saddle about 20 years ago, both are still working great with no problems. Thanks for the review especially the piece on refilling the jack oil. I am a fan of your reviews because they are thorough and objective. Thanks again for your efforts.

[@ProjectFarm]

Thanks and you are welcome!

[@RangerDanger66]

sometimes more expensive doesnt mean better!

[@anthonymartin8769]

Bought a motorcycle floor jack about 20 years ago from HF. I have used it on Road Kings and Heritage Softails and is reliable and I have never felt it being spongy or cheap. Great tool.

[@terrenceolivido741]

Harbor Freight, yeah i remember them from 40 years ago. Nice to know they have maintained - or i hope they have - a high quality company.

[@a57chevy43]

In our tire shop we actually have the Daytona, Pittsburg, and the snap on on. They get used thoroughly in the shop. Snap on has been the only one to quit on us. But it was under warranty by snap on and they have replaced it after almost a year old. All three jacks are approximately 3 years old now. All still work. The Pittsburg definitely seems the most worn out. Casters are much looser than the other two. But all still work great.

[@ProjectFarm]

Thanks for sharing.

[@msk3905]

@Street Performance Bikes "People who buy the most expensive tools are the same ones who live in a 1 bedroom apartment drive a mustang and have a versace shirt or gucci bag. Its all in the mindset. LOL you just made my day! However, I own 2 homes, have $300K income and drive a Mustang, do I need to rethink my play car decision 😞

[@slalomking]

@@msk3905 sure you do

[@michaelmay5453]

I've noticed that SnapOn is now cheap crap with a high price tag. They used to make REALLY high end stuff and a lot of us still have and use those tools but these days they just make crap. The hand tools were pretty good until a couple of years ago.

[@msk3905]

@@slalomking BSME, MBA, 26 years experience and an currently an officer for a large company. I am not sorry for the hard work that I put in over my career leading to my success

[@justbuggin67]

“The Maasdam was built on a Monday” I laughed too much at this. Or it may have been built on a Friday and they just wanted to leave. Great video as usual Todd.

[@bobbygetsbanned6049]

Yeah that looked like Friday after lunch build quality.

[@NoName-qs6ei]

Or Mandatory overtime Saturday.

[@publicmail2]

or a tuesday , weds, thurs....

[@ProjectFarm]

Thank you!

[@Colorado_Native]

Like the old saying, "The first five days after the weekend are the worst." Another great job, Todd. Thanks.

[@richmac918]

I purchased a Daytona a couple years ago because it looked like it was well built and reasonably priced for what it was. I've used it quite a bit over that time and it's worked great. I would have preferred to buy a US made product (Snap On) but it is just too expensive. I could justify it if it were 15/20% more but not 3 times as much.

[@ProjectFarm]

Thanks for sharing.

[@keep_m_running893]

snap on made in US??? need to check on that...

[@richmac918]

It’s not? Then I have zero regrets

[@kodoan411]

Same. I've got the regular Daytona (not the low pro) and it is a sturdy, well made piece of kit. Until the U.S. starts up its factories again, I'll stick with harbor freight for most things because EVERYTHING is made in "chy-na" nowadays. I figure, if I have to give my hard earned dollars to my enemy, it will be as few dollars as possible.

[@HemiHunter]

@@kodoan411 it will never happen that’s how capitalism works companies need to find the cheapest labor

[@SlowJo]

I really really appreciate the information you have included at the 15 minute mark of how to assess if ones jack needs more oil. thanks so much!!

[@ProjectFarm]

You are welcome!

[@Chief1063]

I always find your creative yet scientific ways of testing anything and everything to be... VERY IMPRESSIVE. Love your channel. Keep up the great work.

[@ProjectFarm]

Thanks, will do!

[@randallslattman3119]

@@ProjectFarm You have really set the bar for testing different tools and products keep up the good work and always stay unbiased to everything. Also I do hope you see the test idea in the comments I've pitched for you. I got some ideas and test methods if you want to hear them.

[@ShiftyKen08]

Yeah, that's exactly why I subscribed! Innovative, comprehensive, concise and clear describe his work and for some reason his voice is pleasant unlike some others. Even the graphs are great as they allow a quick reference and make understanding the readings and ratings easy.

[@uhsul]

One of the things I appreciate most about these tests is your eye for detail (e.g. welds, quality of construction, testing the flavor text) another great test!

[@ProjectFarm]

Thanks!

[@jbranche8024]

This guy is a legend. Wondering if he read all the Consumer Reports issues and finally decided to do his own testing on things that interested him.

[@uhsul]

@@jbranche8024 Actually, He relies heavily on his viewers suggestions in the comments.

[@m-rezaabazar-ghafari8757]

A billion times thanks for a very useful video. A lot of safety advise can be achieved out of your videos for regular non handy audience. Your floor jack and jack stands videos were such one. I believe all these manufacturer owe you appreciation for doing free of charge testing and demonstration of their products to the public.

[@ProjectFarm]

You are welcome!

[@DavidGilesColorado]

Thank you so much for your content. I have learned a lot from you. I don’t know what your background is but one thing you do know is how to test products way better than consumer reports and we know you’re not controlled by advertising. Thanks for your hard work. You are one amazing farmer.

[@ProjectFarm]

Thanks and you are welcome!

[@Chris-nl9jc]

I honestly had no idea that I needed to watch videos of extension cord tests or jack tests at 2am in the morning, but here I am. I always agonize over decisions with tools, so these tests are fantastic, thanks so much for what you do!

[@ProjectFarm]

You are welcome!

[@hxhdfjifzirstc894]

When in doubt, buy locally for ease of returns.

[@abel4776]

First world issues.

[@RoverIAC]

I'm only here because I'm procrastinating about opening this letter which I think might be a speeding fine, at 2 in the morning.

[@KlockoFett]

Dude. Same.

[@Cnightz]

The money spent for the 3 Ton Daytona Jack was definitely a great investment. The low profile gets under any car I've worked on and the height it very nice. I know the sell a wide double pad attachment for doing frame lifting or cross members. When Snap On took Daytona to court for stealing their design and lost I knew it was going to be a hell of a Jack for cheap. Very sweet video Todd

[@servicedogojokeguys2967]

Your not supporting American workers tho. I guess maybe most people don’t care about that tho. Some slave in china is making your jack for a bowl of rice that’s fucked up

[@chxx010]

I agree, I have the same Daytona jack it's. It's been great for investment. I was actually surprise on how familiar the Maasdam looked to the Daytona jack as well.

[@exshenanigan2333]

yeah that lawsuit seems to be the advertisement harbor freight couldn't get even if they were willing to pay for it!

[@joselozano0528]

About to hit 5 years with my Daytona super duty, lifting everything from small cars to full size trucks & SUVs. Never greased it & still smooth as butter. Probably do for a maintenance. Oh & the rear casters come apart for better greasing.

[@TonicofSonic]

Bought mine on sale for $160 two years ago. Glad I did, they went up in price alot.

[@juaerez69]

Glad to find your video. I’ve had the Daytona for about 2 years now. Great Jack and no issues. Would definitely recommend!

[@ProjectFarm]

Welcome! Thanks for sharing.

[@BrianRaby998VL]

Very detailed research and product testing. Definitely a new favorite channel of mine.👍👍

[@ProjectFarm]

Thanks!

[@JSparrowist]

You have the absolute best testing methods I have ever seen! I love how thorough you are and I appreciate you making these videos especially in todays economy where every dollar matters! THANK YOU!

[@ProjectFarm]

Thanks and you are welcome!

[@peanutbutterandjammy]

I have four of the 4 ton Daytona jacks and can't imagine life without them. They are absolutely indispensable when working on big diesel trucks. You just can't beat the quality and price.

[@ProjectFarm]

Thanks for the feedback.

[@jayholewinski]

Your contributions to thorough reviews are excellent in being so informative. We appreciate you.

[@ProjectFarm]

Thanks and you are welcome!

[@JoseRamirez-yh2ll]

That was so impressive in the way you tested those jacks. Very creative, this channel is only going to continue growing

[@ProjectFarm]

Thank you very much!

[@eclecticgentleman]

That Arcan is amazing!!! I've had mine about 2 years now. AAA quality and performance and OMG it's so easy to move around and carry being so light. Well worth the extra price for the ease of mobility

[@ProjectFarm]

Thanks for the feedback.

[@MattTrevett]

I took the side handles off mine for better clearance when installing jack stands.

[@christophers707]

I bought my arcan from costco 6 years ago for $100 great lightweight jack that punches above its weight

[@StubProductions]

@@christophers707 me too! I bought two of them. A 2.5 ton and a 3

[@TheW83]

When seeing the weight of the others I was like "oh geez!" I always have to carry my jack around as I can't roll it to where I need it. It weighs about half that of the Daytona so I'm sold.

[@norvellharris1792]

Accurate, realistic, well thought out testing and video presentation with no pressure to buy.... WIN WIN AND WIN!!! I often reference basically anything mechanical back to this channel prior ro making any purchase. You are educating customers and helping us make more informed purchase decisions!!! 👏🏿!!!!

[@ProjectFarm]

Thanks so much!

[@LGHTSPD675]

I bought a new floor jack based on this review. Also, I have bought many other tools based on your reviews. My favorites are my knipex tools, gear wrench ratchets, irwin side cutters, and many quarts of seafoam. Good tools are hard to come by, good tool reviews are even harder to find, thank you for your straightforward and honest tests, followed up by real world opinion. Well done!

[@ProjectFarm]

Thanks so much!

[@jamesf8783]

I appreciate your channel and reviews. They are to the point, no bs, and quick. Keep up the great work good sir!

[@ProjectFarm]

Thanks, will do!

[@cayetano6547]

This is by far the most informative and thorough video I've EVER seen on ANY topic haha Can't imagine the level of energy and dedication it took. Much respect and thank you. I think I'll go with either Daytona or Pittsburgh!!

[@ProjectFarm]

Thanks so much!

[@KF1]

Weld-quality had a lot of variance. For something that holds 6000lbs, was nice to see the clean finished welds. Most people probably wouldn't even check. Great thorough review.

[@ProjectFarm]

Thanks!

[@EnjoyCocaColaLight]

I'm not even certified and I cringed at some of those welds.. Terrible craftsmanship.

[@additudeobx]

Yeah, it kind of like, "If they can't get the welds right, then what else didn't they get right"?

[@brandonweigel6309]

@@EnjoyCocaColaLight yeah, some of them reminded me of my welds back in highschool shop class. 😅

[@EnjoyCocaColaLight]

@@brandonweigel6309 A simpler time, highschool :D

[@Daidis]

Well, now that we have this, I suppose we need a jack stand showdown as well. Could do rated weight, time on stand (in theory should be indefinite, but hey), and angled capacity since not all garages and driveways are perfectly flat and sharper angles can significantly compromise the strength of the jack stand.

[@summervillesean]

And test if you can disengage the jack stand with a load on it. Harbor Freight had to recall a bunch of theirs years back because of this, causing a safety risk.

[@fattykardashian4446]

I still have a set on the recalled jack stands from harbor frieght if project farm wants to test em with it😆

[@willjohnsonjohnson]

​@@summervillesean I replaced the pins with quick release pins, the ones with the ball on the end. Makes it hard for them to slip out.

[@cowrocket3870]

Could see how fast they sink into blacktop too!

[@davidturk6170]

@@cowrocket3870 - I always place my jack stands on 3/4” plywood (get construction scraps out of dumpster if I need to replace)

[@billfendley7531]

Great information. I got a 4 ton Daytona and found out quickly how much extra work I've been doing in the shop. Thanks for the help!

[@ProjectFarm]

You are welcome!

[@jd44194]

I went for the Pittsburgh built on a Wednesday. Couldn’t be happier with the purchase. Thanks for doing what you do in this channel I am a huge fan

[@ProjectFarm]

Thanks so much! Thanks for being a huge fan!

[@ericrichardson3332]

Daytona jack seemed pretty comparable to the snap on jack for the price difference I think most people could over look the smaller front wheels and the slight difference in the rise height.... 300$ vs 1000$ is an impressive savings for a few minor differences

[@ShitboxShenanigans]

Fairly certain the took snap on’s patent on the design. Snap on tried to sue but the time ran out on the patent or something like that

[@denali999]

Worth noting the Daytona is literally 99% the same as the Snap-on. As in the same factory makes both jacks. HF got sued by Snap-on for this and won!

[@TheReal1953]

Some of HF's ICON tools are giving Snap-on tools much grief. Like their torque wrenches.

[@ProjectFarm]

Thanks for the feedback.

[@ericrichardson3332]

@@ShitboxShenanigans the patent running out was a good thing for customers now they have other options other then snap on over pricing their tools and accessories.. don't get me wrong here snap on is a great company but competition keeps prices competitive

[@jwhowsezjwhowsez5448]

This is EXACTLY how all comparison videos even how to videos should be done. Quick to the Point and only showing details and whats important. no BS back Stories or Opinions. There's no waste of time! No wonder this vid is popular. Its easy to watch all the way to the end.!

[@ProjectFarm]

Thanks so much!

[@gatorhaterdl]

Anything PF reviews is like this. This YT channel has saved me so much time and money i could never say TY enough. But Thank You for real PF.

[@Tico09]

Your channel is by far the best. Your reviews are really hands on and not just talk. Thank you for your time and effort.

[@ProjectFarm]

Thanks and you are welcome!

[@lancelot1953]

Excellent presentation (as always). Something I would emphasize for farmers/ranchers who may have to use a jack "in the field", consider the weight of the jack. It appears that as I got older, my tools got heavier! A light jack like the Arcan is very useful when it comes down to raising an implement/implement part off the ground in awkward positions/location which is usually when/where farm machinery fails. Thank you for these practical tests, Ciao, L (Morningside and Starshine "Project" Farms).

[@ProjectFarm]

You are welcome!

[@6speeddakota]

I bought an steel arcan 3.5 ton Jack probably 15 years ago from Costco. It’s been the best Jack and has never given me any issues. Best thing is that it cost less than $100

[@bobbygetsbanned6049]

It seems everyone got that Costco Arcan lol.

[@ProjectFarm]

Great jack at a great price!

[@cocodojo]

We're gonna need Todd to test that.

[@jtb6075]

I got it too, its a really good jack

[@jasonporrazzo3573]

I got that same deal for the red hybrid jack. I love it, and 10 years later it’s still going strong.

[@kaeto]

I've had one of those Daytona jacks for maybe 5 years. Been very happy with it. It has good tolerance to side loading, which is something that always concerns me as I don't want my jack breaking sideways on an imperfect lift.

[@ProjectFarm]

Thanks for the feedback.

[@philliprodriguez4899]

Every video on this channel is a learning experience. I have been using the same floor jack for 20 years and have never even checked the oil level. After watching this video, I will go ahead and fill the oil level in my 20 year old jack that has worked great since day one and still works great.....

[@ProjectFarm]

Thanks for sharing.

[@OverlandOne]

All of your tests are very in depth and you always give us all the information we need to make a buying decision. You just helped me decide which jack I need and I thank you.

[@ProjectFarm]

Thanks and you are welcome! Glad to hear!

[@mueckenhoeffer]

Update! Based on this review, I just bought the Daytona (in metal flake red since it was on the top of the stack and these things are heavy). Needed it to level a shipping container (8,200 lbs empty). First, those big wide wheels make it somewhat easily transportable across dirt or grass. I used two each large pieces of 5/8" plywood under the wheels to keep the jack from sinking once in place. Keep in mind that a shipping container is a very rigid steel box, so jacking just a corner up raises the whole end of the container(4,200lbs roughly). I was able to pump the jack one handed to the desired height and nothing creaked or groaned on the jack while I placed additional blocks under the container. Money well spent so far!

[@ProjectFarm]

Nice! Thanks for the feedback.

[@matthewlee2686]

Just use bottle jacks

[@h8GW]

Sounds like he possibly had clearance issues and bottle jacks are not exactly low profile.

[@matthewlee2686]

@@h8GW dig out what you need. Im jacking 2 now 6ft high with 2 bottle jacks

[@406MenaceRacecar]

How was it $99 ?? We paid $199 on sale

[@AllThingsMech]

Great tests as usual, Todd! It has long been rumored that the Daytona jacks are made in the same factory as Snap On. I tend to believe that based on my personal experience (heck, even the wheels are the same despite the diameter being slightly bigger for the snap on). We've purchased three Daytonas for our shop and they have never missed a beat in 3+ years of hard use, despite being exposed to very harsh, sandy desert conditions out here and lifting everything from Toro lawnmowers all the way up to Massey Ferguson hay swathers. People like to poo-poo on anything from Harbor Freight, but the Daytona jacks are hands down one of the best purchases you can make there. Professional grade all the way.

[@ProjectFarm]

Great to hear!

[@aerokac]

You sold me, where could I buy it in Europe 😂

[@da324]

@TheCheesePlease They had one model that had issues. I've bought some from them and had them for years with zero issues.

[@jonhansen4745]

It wouldn't surprise me if they are made in the same factory. I bought a 3 ton Torin Super Duty last winter & it looks identical to the Daytona & Snap On..

[@alpha2turbo]

@TheCheesePlease you know Snap On has had recalls for jacks and stands also right?

[@shawnwise2458]

I constantly tell all my friends about your reviews, you do great work and make it easier for us to spend our hard earned 💰 Thanks for the effort and planning involved.

[@ProjectFarm]

Thanks so much!

[@ethanwatson8029]

I appreciate how straightforward and unbiased you are. Really sets a confident record for the data.

[@ProjectFarm]

Thanks!

[@OG_COOKIE]

bought a couple daytonas in my shop when they first came around. Used them daily and hit the pressure bypass on each one a couple times a year, and still no problems out of either one. Even the sticker still looks good on one of them.

[@ProjectFarm]

Great to hear!

[@M3D1C2121]

Might be a bit of a strange idea, but a test on tarps would be nice. Though I'm not sure how many tests could be performed outside of durability like tearing and wearing through from use, and weather resistance. Suppose weight capacity could be tested as well.

[@hydorah]

I'd appreciate that!

[@tubewatcher5012]

This ^

[@yewtreefire]

@@hydorah me too

[@ProjectFarm]

Thanks for the suggeston.

[@thra5herxb12s]

Yes quality Tarps cost an absolute fortune these days and don't really last that long, but do they come branded and how can we really know who makes them.

[@rumriverpikelake]

Just found your channel - I really like your format for testing. I especially like this particular video because it confirms I made a good choice when I bought our Daytona jack last year. Thank you

[@ProjectFarm]

Welcome! Glad you found the channel! Thanks for sharing!

[@THEBULLETPROOFGARAGE]

Another fantastic video! I will definitely watch it again when it's time to buy a new floor jack. Thanks again for taking the time to post this!

[@ProjectFarm]

Thanks and you are welcome!

[@johnnieguitar5724]

Very very thorough test! Thank you so much. I don't do any under-car work any more, and wish you had been doing these tests decades ago. I hope people in 2022 realize how lucky they are to have reviews of products done so expertly and honestly. Cheers from Alberta, Canada! :)

[@ProjectFarm]

Thanks so much!

[@raspucin70]

The Jack Reacher (pun intended!) test was genius. How often you have to slip the jack far underneath the car to reach the lift point? Great job PF!

[@g.tucker8682]

Good point!

[@timrobertson299]

That was a good point as I hate it when my jack will reach but you cant use the handle to raise it because it hits the underbody etc.

[@Low760]

It's not that uncommon to get a car started into the air from a safe lifting point.

[@bus6292]

@@timrobertson299 That's the biggest problem I have with my Acdelco floor jack.

[@NONO-hz4vo]

All depends on the car. I have worked on several where the "textbook" lifting point is very deep.

[@jordansimpson9519]

Thank You! I am currently researching a floor jack to buy and this helped me immensely.

[@ProjectFarm]

You are welcome!

[@rwendell0912]

These are the best videos for information on products.Thanks,just got my new Daytona yesterday.

[@ProjectFarm]

Thanks!

[@speedmaster001]

I have the Arcan aluminum 3-ton floor jack. It has been serving me well for the past 10 years. Still look fresh like I just purchased it last week. I used it to lift my 2 SUVs and a sedan, with no issues. I am glad to see it performing well on these tests.

[@ProjectFarm]

Thanks for sharing.

[@jubalwright421]

I have a canadian re-badge of the arcan aluminum, great jack, no problem with my heavy trucks, I'm also in a wheelchair so it being lightweight makes it WAY easier to move around the shop or lift onto my lap if I have to use it in the driveway, I absolutely couldn't lift my old steel jack

[@MattH-wg7ou]

I want that Arcan. Lightweight and looks well made. Would it serve me well with a Tahoe and an Accord?

[@jubalwright421]

@@MattH-wg7ou mines a re-badger arcan, I have a 3/4ton suburban no problems lifting it, quite lowprofile too so I can't see you having any issues with your accord either

[@daveharness70]

I have the re-branded JEGS version of it. It was great for about 5 years. Then one of the power unit springs got stuck. Won't lift now. Contemplating just buying a new one as I'm having problems finding the replacement part for a reasonable amount.

[@chrisfreemesser5707]

Bought the Husky about 2 years ago, very happy with it and glad to see it performed well here. "Real" jacks like these are a surprisingly large step up from the smaller portable hydraulic jacks many DIYers have and are definitely worth investing in if you work on your own cars a lot

[@FunBitesTV]

Agreed, some of the cheaper jacks are at best ,inconvinient and dissapointing. At worst, plain dangerous.

[@bigwilly43729]

My little Craftsman jack served me well for a number of years, but in hindsight, I wish I had sprung for a bigger, low-profile jack like one of these tested.

[@tapdat6754]

I just do regular maintenance and minor repairs with mine, and having a floor jack makes it so much faster, easier, and safer to work on my car.

[@ProjectFarm]

Thanks for sharing.

[@ericdowdy2362]

I like his vids because he doesn't ramble. Lots of people (way too many) want to tell their life story and turn a 5 minute video into an hour. This is all meat and no filler. Thanks!

[@user-mp8er1ds9x]

Nice review, thank you. Of most value was the reach and roll test. Bought a pair of orange with white handle $50 two-ton HF jacks in 95. They still go up and down. Hope the Daytona's do that.

[@tyneshaanthony5768]

This just in time, started looking at floor jacks this past weekend. And the Daytona has been my front runner for price and by the quality of the build. Thank you again for doing these tests to help the folks who can't do all these wonderful tests. Your tests with charts and covering the information that is most helpful!

[@ProjectFarm]

Thanks and you are welcome! Glad to hear!

[@45eno]

I’m sure you are aware but make sure to get a 20% off coupon before the purchase. With Labor Day coming up there will be sales and flyers. Sometimes those coupons don’t work on that jack so sales might be the best time to jump on a new one.

[@fixitallpaul4847]

See my video of why I wont use daytona. Ive seen 3 of these jacks unable to hold the load.

[@45eno]

@@fixitallpaul4847 Just searched your videos twice and couldn’t find any video about Daytona jacks.

[@45eno]

@@fixitallpaul4847 Thanks for sharing the info. I'm a very light user of them and I always support with stands when getting under.

[@philly7558]

I need a new jack and now I know exactly the one I need. Always a big help, thank you once again for your this channel.

[@ProjectFarm]

Thanks and you are welcome!

[@realimike1971]

Once again, your comparison testes are spot on with what I'm considering purchasing. My current jack was purchased at Harbour Freight about 20 years ago when they first came out with their aluminum, low profile fast pump jacks. I also purchased their original orange jack stands with white risers and have had NO ISSUES with either, except the jack is leaking a due to a bad seal at the release/lower lever point. In my opinion, when using tools that are being used daily or on heavy work, they need to be replaced within a reasonable time due to safety, like jacks and jack stands. like ALWAYS, Project Farm, your videos provide GREAT information and content.....THANX from California

[@ProjectFarm]

You are welcome! Thanks for sharing.

[@Kflash3782]

I have the Daytona, and it is a great value. It has a quick lift lever that raises the arm to the point of contact before engaging the load. Saves a lot of time on positioning the jack.

[@lowerclassbrats77]

I have a Daytona. It extends high enough for my wife's Honda Pilot but it also has a low enough profile to get under my lowered Hyundai Accent (no I didn't lower it, the dealer did and added a sport suspension for some reason 😄). It's a beefy jack, raises up super quick, and lowers even quicker.

[@bobadkins7377]

The Daytona would be my choice.

[@delilahmartinez9390]

Im going with this brand!

[@benb4343]

I havent had any issues with my Daytona low profile jack🤘

[@BL-yj2wp]

I had an old German made Febi Bilstein floor jack with a spindle, the thing was huge and heavy, 130lbs, and even after 60 years or more as good as new apart from some surface rust. Sold it for 50€ because I don't work on cars and don't have the space. Looking at these the buyer got a damn good deal :(

[@ProjectFarm]

Thanks for sharing.

[@pedlpower]

A very comprehensive test. Thank you. I've had the Pittsburgh from HF for about a year now. Works just fine for a DIYer.

[@ProjectFarm]

You are welcome!

[@xtripv108]

I recommended it and you actually did it!!!! A MILLION THANKS!!!!!! Got the Pittsburgh jack hoping it would be worth more than the price, your video proves it. I wish I could subscribe twice lol.

[@ProjectFarm]

You are welcome and great choice on the Pittsburgh

[@bbrewer609]

Another outstanding product review. Best part of your reviews is the presentation efficiency, absolutely no wasted time, just facts. As always unbiased, thorough, fair and impartial. I don't buy anything vehicle/shop related until I check in to see if you have a done a review. Thank you.....now off to Harbour Freight for a Daytona Floor Jack.

[@MitchBollig]

14:48 Fantastic! You take a moment to remind folks to use jack stands. Thank you! You are the best.

[@ProjectFarm]

Thanks!

[@dicedoomkid]

Thanks for making such a well made video on the subject. The internet needs more of this. Probably going to get an Arcan jack...

[@ProjectFarm]

You are welcome!

[@stf2400]

If I’m buying something I always check this channel to see if it’s been tested. Family friendly and honest reviews, what more could you ask for?

[@ProjectFarm]

Thanks!

[@cosmicallyderived]

Think about Scotty Kilners line for his prizes: leave a non-offensive comment in the box below; or whatever it is he states each time. Apparently some of the viewers get a little off at times

[@_BangDroid_]

So glad I found your channel. I don't know if you realize but you are a true champion of the consumer. Your depth of testing is so eye opening and your objective analysis is outstanding.

[@ProjectFarm]

Thanks!

[@Brian-ie2un]

I watch this channels test on vehicle stands and I never knew what I didn't know. Outstanding test. And the vehicle jack test is no jack up. I'm putting my money where my mouth is and getting a improved jack now I know whst to look for. Cheers.

[@ProjectFarm]

Thanks! Thanks for sharing.

[@billbovee1705]

Every time I buy something now I scan this channel for reviews first. I love my Daytona jack!! Thanks to you I went with it and happy as hell

[@ProjectFarm]

You are welcome!

[@noneya135]

I bought a Daytona 3 ton low profile jack last week. I was glad to see in your review that it was money well spent. Thank you so much for taking the time to create these very informative videos.

[@ProjectFarm]

You are welcome!

[@zachmadonnawesberry3258]

This is by far the most useful content on KZbin I'm very glad you are being rewarded for all your hard work. I love how you put all the over priced tools to the test and manage to prove that just because something is expensive does not mean it's the best.

[@ProjectFarm]

Thanks!

[@matthewttful]

Yup this video helped so much. Iwas deciding whether to get the Pittsburgh or the Daytona and now the choice is clear!

[@viktorabbott2036]

Snap on beats all

[@BeingInTheMessiah]

Great video, almost each jack has a place for some people and you break it down perfectly

[@DrokiHazan]

Thanks as always for your clear and concise videos. I really love how you get straight to the point, reading exactly what they put on the box with no opinions given, then do your best to test what the manufacturers claim. I also love how open minded you are, endorsing tools from across a wide range of manufacturers and origins based solely on how they perform in facts-based testing. And most of all, I love that you reply so often to your comments, but without ever endorsing a single subjective opinion or anecdotal experience from a viewer. You just thank them for their feedback, and move on. You're the epitome of what a scientist is and should be, and I think it's so important for people from all walks of life to see a scientist who isn't in a labcoat working on esoteric and mysterious equipment, but just a friendly guy experimenting with stuff we can all buy in stores to see if it's any good based on tests you come up with in the garage. Great content, thanks for what you do.

[@ProjectFarm]

Thanks and you are welcome!

[@polaris6644]

I'd love to see a comparison of different brand's compressors, something like a 20 Gallon upright from each different brand, all with roughly similar specs, designed for home use. Testing things like time to build air, true CFM, and maybe even do a torture test to see how long they can run continuously. A lot of brands lie about CFM and other specs.

[@kilroymanjaro6951]

Goodyear oil free 20gal vs Mcgraw oiled 20gal vs Craftsman 20 gal.

[@ipissed]

That would be a very expensive test. Rremember he pays for all the tools with the help of donations.

[@NightOfTheLiving8bit]

I’d love to see this too. Largely small compressors that are likely to be seen in a small home workshop or the portable ones for small jobs (other than pancakes) by companies like Milwaukee, DeWalt, etc.

[@ProjectFarm]

Thanks for the suggestion.

[@daveharris39]

Great test. A mention of warranty for each Jack would be a nice addition. I had one of those mini floor jacks from Walmart that lasted 20 years, then after it died, I bought one that looked just like it at an auto parts store - which died within it's one year warranty.

[@ProjectFarm]

Thanks! Thanks for the suggestion.

[@mercedes-amgforlife3237]

Was is the MVP brand? I've had one for over 20 years and it's still going strong. It's a great help when doing ball joints and suspension work cause of it's size.

[@martinedwards4522]

i have a craftsman i bought 31 years ago its still good but love my new daytona long reach lopro

[@daveharris39]

@@mercedes-amgforlife3237 yes it was

[@time2maked0hnutz54]

You Sir are my personal R & D Department for All the tools I actually use! Thank You & Keep up the Great Work!

[@ProjectFarm]

Thanks, will do!

[@smal1393]

Another well thought out test and excellent presentation, thank you.

[@tcfbrp8807]

Daytona makes a "Low profiel, long reach" model which has a longer and flatter saddle. I bought it several years ago and love it! The only jack I've found that fits under my car with ease.

[@ProjectFarm]

Thanks for the feedback.

[@bajafishtaco]

The Pittsburgh also makes a a low profile version mine is over 8 years old and still works perfectly. I lift trucks and big caddies weekly with it .

[@jkljkl218]

Had my daytona for 3 years, Been loving it the moment I got it! Love the guide on how to oil the jack too!

[@ProjectFarm]

Great feedback on the Daytona! Seems very well built!

[@jkljkl218]

@@ProjectFarm really well built! Only thing I've had issues with is the paint on the handle, Makes sense though, I use the handle as a cheater bar 🤣

[@danielmutchler2268]

Fantastic review. Answered all my questions about a new jack purchase. I have been thinking about a new pittsburg or possibly Daytona. Thank you very much for making this video.

[@ProjectFarm]

Thanks and you are welcome!

[@gretalaube91]

I was just shopping for a new jack! I love your down to earth unbiased reviews! Thanks!

[@ProjectFarm]

Thanks and you are welcome!

[@ulogy]

Thanks for the consistently great content!

[@ProjectFarm]

My pleasure!

[@jimmybarr9411]

I bought the Husky jack about 4 years ago as my first floor jack. So far, it’s held up well with regular use with no maintenance done to it yet. I only paid $119 plus tax when it was on sale at Home Depot. One of the best automotive tool purchases I have made. I thoroughly enjoyed the video, as always!

[@ProjectFarm]

Thanks! Thanks for sharing.

[@TravisWeir]

I just got the Daytona jack for Christmas on your recommendation, and it's fantastic! Thanks for the advice!

[@ProjectFarm]

You are welcome! Glad to hear!

[@1972CB350]

This man is a life saver. Some of those welds could kill a person. Cheers to Project Farm, the best of KZbin right here.

[@ProjectFarm]

Thanks!

[@marcuscoquer5958]

I am endlessly impressed at how clearly and quickly you are able to impart information. It is quite a skill.

[@ProjectFarm]

Thanks!

[@bobbygetsbanned6049]

One of the most important factors in a floor jack is the availability of seals. No matter how good the jack is the seals will eventually fail, if you can't get replacements it's a throw away item. I don't think you can get seals for HF jacks, but Arcan and some other brands have seal kits available.

[@1pcfred]

I'm sure you can find any seal if you're willing to browse Chinese websites.

[@therising1]

Seals are available for the Pittsburgh jack. Just not from HF.

[@PhillyRacer121]

Hf now has a parts catalog and offers parts support for the bulk of their tools and equipment. Seeing as the daytona is made in the same factory as one of the snappies im sure you can get seals that way too.

[@Nick-jg9ck]

Saying a harbor freight is a rip off of snap on you probably can use those

[@tonysheerness2427]

By that time are they worth keeping, cylinders would be scored.