Best RC Drift Chassis | Rhino Racing Shark Full Build

Full walkthrough and build of the Rhino Racing Shark Yokomo Conversion which works on Yokomo RD1.0/ YD2Z RC Drift Cars
Parts Needed shown in this video: • How to Build a Rhino R...
Note* The newer transmissions do not need a flange bearing as I state in this video, my first kit did but that was from a couple months ago. All recent kits should use the standard bearing they are supplied with.
This system is for sure one of the best available for RC Drifting. It Turns your standard bellcrank steering setup into a direct drive system allowing you incredibly precise tuning adjustments. It makes the car feel much more stable and helps take out unwanted play in the front end of the car.
It takes a bit of time getting things dialed in but its worth the effort in order to benefit fully from the build.
Would you like your product built or reviewed on my channel? Email me at [e-mail]
Any purchases from these links helps support this channel:)
Mip Wrenches: amzn.to/445qB2z
Mip Tips for Drill!: amzn.to/3pPjsp8
Compact Drill for Bits: amzn.to/3Og3v4F
Mip Wheel Nut Drivers: amzn.to/44E2hWq
Body Scissors: amzn.to/3Di1aQI
Flush Cutters: amzn.to/3K2SL7f
Solder Station: amzn.to/3DcPNtf
Current Charger: amzn.to/3PZurqT (Needs Power Supply)
3m Mounting Tape: amzn.to/3DoFrGHMIP
Metric Wrenches: amzn.to/3NY59Xt
JConcepts Camber Tool: amzn.to/3DhLxbW
Thinktank Cable Bag: amzn.to/3rqEwmd
My Camera Gear:
Camera: amzn.to/44ni8J0
360 Camera: amzn.to/3OpfWvn
Small Rig Power Pack: amzn.to/3rvj8fJ
Tamron 11-20 e mount: amzn.to/3NRfHaB
Atmos Monitor: amzn.to/3D9oiAP
Cable for Monitor: amzn.to/3XLzr4d
SD Cards I use: amzn.to/3POHpaM
Editing Gear:
Microphone(SM7B): amzn.to/46OyZWV
Mic Arm: amzn.to/46LdaaV
Mouse: amzn.to/3NT0vKc
Keyboard: amzn.to/3Ohh7gf
Mac Stand: amzn.to/3PZhtJp
Card Reader: amzn.to/44Dy8GK
Any gear purchased through these links helps support this channel!

[@Pixel_Heart]

This was so cool to watch!!! Great job!!! Thanks for sharing the whole process👏

[@SeanLewisMedia]

Thanks for the feedback! I appreciate it as always!

[@joaquinrobles2474]

Thank you for sharing the whole process and your time. I have a mst rmx 2.0 all electronic have been upgraded and i have had it for about 2 years now or more and I tear it up at my local track and tandem well. I have been wanting to upgrade to a better chassis but dont know what to get. Thanks 👍

[@SeanLewisMedia]

Glad I can help!

[@HOUSECAT47]

Can you do this with a yokomo SD LTS or is this conversation only for the RD

[@SeanLewisMedia]

I believe it should work fine as far as the chassis lines up but you would have to do a little messing around to get the LTS battery setup on the top plate. You could email the crew at super-G and they should have super solid answers for you to be safe. The fun think is that most of these cars and parts will work together so theres for sure hope that you could get it figured out. You could start with the Rhino Racing Shark DDSS steering system and work your way back as you go over time. That would honestly be where I would start with the build, Yokomo LTS, add the RR DDSS and you would have a absolute unit! Hope this helps!

[@AndysRC89]

just out of interest, would a rd1.0 kit just bolt straight onto the shark chassis plate.

[@SeanLewisMedia]

I believe so, but am not 100% sure. The shark changes some placements of the transmission so it might not on the rear end. I do think the fronts match exactly though.

[@sefferrr]

BIG GASSSS

[@SeanLewisMedia]

🙏🏼

[@Fbody_123]

If you don’t mind me asking roughly how much would something like this cost to build ?

[@SeanLewisMedia]

This build is probably around $1200 to get to the point I’m at now. But it started as a rtr and I pieced it together over about 6 to 9 months. You can get started with a really good comp setup for around $700 if you’re willing to run a less crazy chassis. The main money draw is really in the electronics from my experience.

[@Splinterx182]

Yokomo uses 4.3mm ball studs for the bottom shock ends while for every other ball stud is 4.8mm.

[@SeanLewisMedia]

Yo I’m sorry I never responded to this but it really helped me out and I just wanted to let you know!

[@Veterans4life]

Thank you for sharing this… I just built mine it’s awesome. The piece you put to the side. Where does it go?

[@SeanLewisMedia]

What time mark in the video is it at?

[@Veterans4life]

@@SeanLewisMedia it’s at 45:46

[@Veterans4life]

@@SeanLewisMedia did you find the part I’m talking about?

[@neildaniels5443]

He m8, my Shark lower deck came with a single 20mm piece of aluminium, it has two screw holes and a slot in the middle? What is it for and should there be two of them? Hope i managed to describe it ok 😅 .......

[@SeanLewisMedia]

I believe what your looking at the the rear battery stop. It mounts right in the center of the chassis. About 3/4 back from the front right at the back of where the battery goes. You should see the two screw holes, the are long and allow you to slide it back and fourth depening on where you want it set. I hope that helps and answers your question! Let me know:)

[@neildaniels5443]

@@SeanLewisMedia fnx m8, I see it now , no instructions for da deck so struggling a bit, don't wanna mess it up , cost a pretty penny 😆 , fnx again fa ya help m8, keep it sideways 👍

[@minez4088]

Hi where did you get the instructions to put the shark together?

[@SeanLewisMedia]

I believe I found them on super g's website. Its on this page supergdrift.com/product/shark-yd-2-conversion-kit-red-purple-black-rhino-racing-yd2-ddss/?attribute_pa_color=red&attribute_kit-type=Full+Shark+Conversion+Kit

[@minez4088]

Great thank you very much. Do you dable in 3d printing

[@SeanLewisMedia]

@@minez4088 I have not played with 3D printing yet but I really want too! Just not in the budget currently. How about you? Have you gotten into it?

[@ninolopresti9519]

What is a rhino racing shark?? Can someone explain?

[@SeanLewisMedia]

So the Rhino Racing shark is a conversion for the Yokomo RD/SD line of chassis, they also have conversions for reved chassis. You can buy a complete rhino racing shark now as well. It comes as a complete roller from the Super-G RC Drift website. You can also see the chassis options on their website👍🏼

[@sajjadhussain8828]

Bro plz can u send me link for belt drive differential kit plz

[@SeanLewisMedia]

supergdrift.com/product/shark-belt-drive-conversion-kit-for-shark-transmission-red-purple-black-rhino-racing-rr-754-b-r-p/

[@michaelseguinot393]

I’m looking to getting the shark tranny conv. Will it bolt up to the yd 2 chassis

[@SeanLewisMedia]

I believe it does, but something about the length of the top plate changes. If that combo includes the adjustable top brace it should be ok. Id still suggest emailing super g to ask though that way you dont run into any potential issues

[@michaelseguinot393]

@@SeanLewisMedia thanks bro

[@SeanLewisMedia]

Of course man! @@michaelseguinot393

[@destachedestach3278]

Just want to make sure.. this is a belt drive? 😂

[@SeanLewisMedia]

I have one that’s belt drive and one that is non belt drive haha. My main is non belt drive 3 gear setup up with a clsd

[@stnefan6923]

HI, CAN SOME ONE TELL ME WHERE I CAN BUY IT?

[@SeanLewisMedia]

On the Super G Rc drift website is where I got my setup from

[@stnefan6923]

@@SeanLewisMedia thank you 🙏

[@stnefan6923]

Can you tell me a good car for 300-400€ please, I’m new, or are they bad for this price?

[@SeanLewisMedia]

@@stnefan6923 If your newer and looking for a first car that is a whole package I would suggest looking at the “MST RMX 2.5 RTR”. That would be a great car to learn with and it’s the best option for a ready to run in this current market. It would get you started without to many issue and you could upgrade as you learn.

[@stnefan6923]

@@SeanLewisMedia ok thank you 🙏