Best suspension MOD for your restomod Mustang

Flexibility and options were are the forefront of the decision to go to this style suspension. But more honestly I had some parts laying around already 🦾. I have to say it was a good decision and feel I’ll be able to dial it all in a bit further in the next few weeks. I want to share a lot more on the driving experience with this suspension set up so please stay tuned. Much more than a few laps around the block! 🤙
SN95 mustang suspension uses the McPherson strut style system. The particular configuration I’m using allows for a lot of adjustments and dials. This is a street car and to be drive. Looking back on the decision I wouldn’t change the route I took here.
Typically builder remove the shock towers for the mustang II set up. This set up has been proven and there are amazing rides on the road that use it. However, the McPherson system has also been proven on many of famous street cars around the block. While this set up in the video focuses on 67 through 68 Mustangs it also applies to many other generations of Mustangs as well. I look forward to the comments and discussion about the claim of being the BEST mod. This is a personal experience and definitely not the only experience to come. Please stay tuned for more!
Read our blog post about it here... brianadkisson.com/1967-1968-m...
PARTS LIST:
(Affiliate Disclaimer: The following products may contain affiliate links. As an Amazon Associate I earn from qualifying purchases. Thank you for your support of our channel!)
(When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.)
AJE K member - ebay.us/k6plMY
AJE Full Kit - ebay.us/445AZc
street or track export bracing- ebay.us/t5J42U
Strange coil over kit- ebay.us/QVEqbf
Strange Struts - ebay.us/SKmv6A
Nissan Versa Electric steering - ebay.us/wKOMO1
AJE SN95 Drop Spindles - tinyurl.com/3weykxfp
Steering Shaft Universal U Joint- amzn.to/3AhtXTp
Column Shaft with Floor Mount- amzn.to/3pFw8uZ

[@ClassicNation]

I really enjoyed the video, Brian! Nice work. Great looking fastback! 🙌

[@CMOSX]

Great video and nice to see a new vid! Man your editing went to 1000% on this one bro! :)

[@wolfthornhawkridge5705]

Good information as always!

[@FollowTheBuilds]

Thank you! Appreciate the support for sure.

[@markshalloup3569]

Id like to see a video on your electric steering conversion on the fastback Thanks

[@FollowTheBuilds]

Let’s do this! I have one in the works. That’s for this idea.

[@Observers101]

I’ve done the exact Aje mod. Need to do the export brace and power steering! The original aje kit made a clunky noise. Switched to the same caster camber kit and strange shocks.

[@QuinntumAZ]

Really enjoyed the video! And yes I'm one of those guys thinking about going to a Mustang II setup on a 1966 Mustang. It's been a couple years since you installed AJE system, how's it holding up?

[@craigbeveridge2492]

Hi how low does the K frame cross member hang below the chassis rails ? It looks pretty low and is there any adjustment for lower control arms... tganjs

[@FollowTheBuilds]

No lower than the stock engine frame mounts. There still is some wiggle to customize the height of the engine to your needs (before you have to cut the tunnel). On these lower control arms yes there is plenty adjustment on the Racecraft 11.5” arms. One caution here is they work well with my wheel choice of zero offset. Turning radius could be limited with other wheel choices. I’m working on a mod that would allow more wheel options.

[@dcstang67]

Couple questions. What size coil springs did you end up using? What size sway bar did you use?

[@FollowTheBuilds]

Hey there…12” coil springs 175#. 1.125” sway bar.

[@MrMikeivo]

What spindles are you using?

[@donduran3994]

Welcome back! How were the welds on your AJE crossmember ?

[@FollowTheBuilds]

Yeah!! Thanks - K member welds looked good...no issue there. I believe that issue with AJE has been solved.

[@jpmendoza138]

Your videos are great. What is your wheel and tire set-up?

[@FollowTheBuilds]

Many thanks! American Racing wheel VN510 18x8. 255 tires all away around.

[@leewilliams8917]

Can't find the parts on eBay?

[@mystang0304]

I'm running a 351c, does this setup need a rear sump pan?

[@FollowTheBuilds]

It does. A fox body style oil pan was what it was designed around.

[@Frankensteinfabrications]

so is this the coup to a fastback car ? or is this a different car ?

[@FollowTheBuilds]

Thanks! This is a true fastback. Another Coupe to fastback is coming soon!

[@lui472]

"like a Porsche" and shows a McLaren. @1:27

[@rogerboon5001]

How about just get to the point.