Best Value Brushed Beetle ESC - Soldering/Usage Guide (2X 15 Amp Dual-ESC)

Looking for the best budget ESC for your next bot? Look no further than this budget option!
bit.ly/DESC-2x15
Note: To diable mixing, you can bridge the "independ" solder points on the back of the ESC.
User Guide: bit.ly/2x15UserGuide
Thanks to the continued support of PCBWay - check them out for PCB Fabrication, CNC machining, and more! bit.ly/PCBWayJustCuz
Just 'Cuz Robotics Website: justcuzrobotics.com/
Just 'Cuz Store: justcuzrobotics.com/shop
Try PCBWay's CNC Machining or PCB Fab using this link for a $5 new user credit: bit.ly/PCBWayJustCuz
Instagram: @JustCuzRobotics
/ justcuzrobotics
Bloodsport KZbin Channel
/ bnsrobotics
@bloodsport_battlebot
/ bloodsport_battlebot
@retrograde_battlebot
/ retrograde_battlebot
Bloodsport/BnS Facebook Page:
/ bnsrobotics
Music by Streambeats
#CombatRobotics #beetleweight
Timestamp
00:00:00 Intro
00:00:35 ESC Overview
00:01:30 Add Motor PCBs
00:03:24 Motor Wires or JSTs
00:05:32 Solder Wires to PCBs
00:06:07 Motor connections
00:07:08 Wiring to Motherboard or Receiver
00:08:31 Motors in Robot
00:09:09 Bind FS2A Radio
00:11:15 Bind Zorro Radio
00:11:29 Why Prior Wiring Doesnt Work
00:12:57 Trim Adjust
00:13:31 Motor Directions are Wrong?
00:14:32 SPONSOR: PCBWay
00:15:07 SSP Wheel Install
00:16:57 Quick Drive Demo
00:17:34 Changing Settings

[@JustCuzRobotics]

Sorry for the do-over, I felt it was necessary to give this video another try after how many complaints I got from people about how badly their robots were driving with the previous instructions. Using the correct wiring as shown here should be far far better! Also apologies that the sponsor ad is outdated - the 9th anniversary promotion ended about 2 months ago now.

[@GearheadCreations]

Yes! Finally someone else is using these too. I found these ESCs on eBay quite a while ago and have been using them in both my beetleweights and antweights just because of how compact they are!

[@HuskyMachining]

what a coincidence, I just wired up 2 geckos to this esc last night and I was having this exact issue. I was going to sleep on it and im glad I did, thanks dood

[@bradleylomas7525]

Wish I seen this before I made my bidirectional dual motor esc purchase yesterday 😮‍💨. I'll be looking for your shop later, definitely.

[@forceofwillgaming8475]

Do you have to use the motor PCB or can you directly solder the jst connectors to the motors?

[@JustCuzRobotics]

You can direct solder to the PCB or to the motor contacts, the board just makes it easier and more durable since the motor terminals are a bit fragile and repeated soldering can cause issues sometimes.

[@marksevilla7242]

Good day Sir, i have a project with 2 brushed motor, i need to make them go straight, with two different motor it will be a challenge, my idea was to connect a drift gyro used on d12, from receiver to drift gyro(wpl d12) to dual(2 channel) brushed esc, will the gyro auto correct the two brushed motor? i built a submersible pool vaccum with 2 bildge pump as propellant but i want to go it as straight as possible

[@JustCuzRobotics]

I haven't had any success using Gyros built into receivers personally. They're all built for cars where you use a steering servo to turn and they aren't designed for differential Drive robots where you need to affect both Channel 1 and channel 2 signals.

[@marksevilla7242]

@@JustCuzRobotics I already solve the problem, I just need the to put diodes on each of the brushed motor, one motor responds to positive voltage turn and the other responds to negative voltage turn, thank you for your reply Sir appreciate it, I'll give you an update if it works, but im positive about it, pool tiles gives rough path for the robot vacuum, i just want it to run straight as possible for effeciency

[@yashnivalkar1131]

Definitely one of the best video out there about brushed ESC.....Bro I need help I am using 5A dual brushed esc for my 3.5ch RC heli I just can get both motors at same speed please help

[@yashnivalkar1131]

I am using channel 3 for throttle sp pluged 3pin esc in ch 3 and yellow wire in ch 4 Also have switched polarity of motor for spinning right direction

[@JustCuzRobotics]

Sorry but I have not used that esc before so I can't provide any help. Try contacting the seller for help.

[@yashnivalkar1131]

@@JustCuzRobotics No problem its same as this but has 5A output. I am getting it working same as this video only problem is both motors not spinning at same speed

[@JustCuzRobotics]

Use radio trims to adjust if the speed difference is not too bad

[@yashnivalkar1131]

@@JustCuzRoboticsIts pretty bad.... I might try one more esc cause speed difference makes a lot of difference in RC heli it starts spinning around.....

[@TheTheknightofblack]

Anyone else get a red flashing light on the main motherboard?

[@JustCuzRobotics]

If you have any technical issues with my products you should not reach out on a KZbin comment. I provide excellent customer support via email at [e-mail] or through the contact us form on my website

[@FaithfulMC]

Umm.. Why is the left side of your robot labeled as right and right as left? that is confusing af. I'm guessing you don't drive a car?

[@JustCuzRobotics]

I drive a car, but I labeled it that way as that is the left and right side in the CAD view looking from the front. I realize it's a little backwards from when driving the bot, but the labels are covered in combat anyway.

[@rudolphpotter4167]

😠 *Promo sm*