BetaFPV Beta95x V3 Review, Filter and PID tuning recommendations and must-do Mods!

[@drids_fpv]

Amazing! I've been flying the beta95x for a few months and I've tried many different tunes from other youtube videos but it never flew very well (luckly reelsteadygo exists). With your tune it flys much much better, perfect for me. I tuned my pavo30 with your tune, tried it and quickly went to your youtube channel to find if you had the tune for the beta95x. I'm subscribed to you for sure!

[@Mekanikern]

Hey Chris, if you find the time for an extra video I'd love to see you tune this one on Betaflight 4.3 🙂

[@johnnyo3947]

I've been looking for that for weeks, and I haven't found anyone who has done it.

[@Mekanikern]

@@johnnyo3947 the other day Ciotti told me that cinewhoops around this size performes much better with prop-in rather then prop-out. It would have been great to see this quad on BF4.3, tested in vs out.

[@cubefpv]

Nobody is asking the obvious question here - What are those things attached to the wall near the printer?

[@andrewfahim93]

Thanks alot Chris I have been waiting for this, appreciate your hardwork

[@onceamantwiceaboy]

Love your tuning videos Chris. Lots us us I am sure have the beta95x v2 (Previous version). Any chance of a tuning video to cover this one and/or the beta85x v2? ....pretty please

[@noobfpvideo1597]

I picked up a secondhand one of these a few weeks ago. I’ll get to know it before trying your suggestions

[@ecoaventurasdelistmo]

what the about the new improved holes Lumenier QAV-PRO Micro Whoop 2.5" Cinequads Edition ,, they say 1404 4600kv but i have seen 2004 not sure the kv,,, to carry a full go pro 10 ... tunning it the full process.. that would be the best chrisrossermax gift ever!!!!

[@werschaf666]

Actually, there's no need to drill through the bottom shroud; just loosen the seven philips screws of the shroud (caution: the three in the front are longer than the four in the back, keep this in mind during re-assembly) and then you can simply move the shroud to the side along with the wires and have direct access to the rear rubber grommet.

[@Dgraboski1176]

I put this exact tune on my Happy Model Cine8. Super smoothe.

[@batdronefpv]

THX Chris for the Tune tips !! I advised a balance PID of 1/1 or 53/53 (better for cinewhoop) and the same I-Term as you. Not affected by filters. No jello or vibrations without modifying the gummies with SMO 4K and FPV camera! On the other hand, I noticed that you had kept the bidirectional DSHOT at Dshot 600 and your CPU at 13% on an FC 405. I switched to DSHOT 300 8K / 4K. What do you think ? Good flights from France ....

[@EvaTheDivarobloxplays]

Good video and thanks for the info. Just swapped to these motors. Going to test this tune out on one of my profiles. Making a tune for BF4.3. Keep it up!

[@sidewaymaster]

I have it!!! But it's very vibration on gopro mount!!! Today, I will mod it like you!! Thank you so much 🥰

[@ChrisRosser]

Yeah! Let me know if it helps 👍👍👍😁

[@sidewaymaster]

@@ChrisRosser Update for bf4.3 RC1 please 🙏

[@viciousShadovv]

Nice review and great tuning tips! Tried to tune my B95v3 alongside the vid with BF4.3 RC3 and after figuring out that i need to enable DHSHOT for RPM-Filtering/Dynamic Idle, i struggled a bit with the new bf4.3 settings (Dynamic Noth Filter » Notch Count; D Term Lowpass Filter » Dynamic Cruve Expo Value; Dynamic Damping has default values of 37 Gain / 20 Advance and i have no idea how to turn that off). Any suggestions? Thanks alot!

[@JoshHardie9]

Thanks for the great video! I was a bit disappointed with the performance of my 95x and I’ve been avoiding flying it. Definitely giving your mod suggestions a try! For a future video you should check out the Flywoo Firefly 1s Nano Baby. I just got one with elrs and mostly love it….like 95% love, however I would be interested to see what you have to say about the tune 😎

[@ChrisRosser]

Glad I could help!

[@mariobeans]

ya the firefly is amazing!!!! I gots 2

[@wolle_der_dolle6236]

Review the geprc cinelog 30 please!

[@davidjohnson6965]

Hi Chris, Just found your channel. Looks like you live a stones throw from me! Thanks for the video

[@khild]

What would be replacement for the 1404 BetaFPV motors that are out of stock?

[@Cre8ionz.]

5:15 min - E6000 glue is the best solution ! You can repair Whoop frames with it because it stays flexible

[@Mekanikern]

Hi Chris, if you are able to I think a nice whoop to look closer at is the brand new Emax Tinyhawk 3. I suspect there will be some of them under the christmas tree this year 🙂

[@alexisshammas3107]

Can you tune the iflight nazgul evoque f5 pleaseeeeeeeeee

[@1979zeesh]

awesome tutorial mate....i recently built this but did minor customization. betafpv 4500kv motors were a big pain in @$$ as ordered 3 sets and all of them were not working. so moved to happymodel 1404 but they had 3500kv only. last night i did my 1st flight and in few minutes motors were hot on a 4s lipo....i landed it to avoid any damage to motors....can this 3500kv be an issue? im not using BF but inav5.1. built has weight of frame, motors, insta360 cam, mamba f722mk4 mini FC stack and elrs nano

[@PitchoDrone]

Do you have a comparaison for the setting on beta 4.4 ?

[@danialfpv]

Yeay, Thanks, Chris for this vid. It's been a long time coming but I'm still on the 1106 motor. 😔Followed your Pavo30 camera plate clamping on this one 😆

[@ChrisRosser]

Thanks for your patience and hope this helps with your tune!

[@FlyZoneFpv]

Great review Chris🤙

[@coilockerfpv]

I love you so much for making this 🥰🥰

[@craxymax]

Hi Chris! Perfect video, do you have changed the esc settings in your tune? Can you post the stock and the tune esc settings? Thank you!

[@thethrillofflyingadrone]

Hi Chris, first of all thanks for your video. May I ask you to confirm if the setting are OK also for the Analog version? Thanks for help.

[@robmulally]

I got the V3 but my motors are different. Very odd :-(

[@mcferran6720]

works this with BMI270??

[@serval_fpv]

Mines can hardly get off the ground nearly needs full throttle to take off is that normal? 1404 motors and 4s 450 mah battery no GoPro etc

[@InfinityDrones]

Where can I find the original CLI dump for the Betafpv 95x v3 - I've tried your settings and my motors are "really" hot. I've tried to load the cli off betafpv's site, but their VTX tables seem to wrong as my vtx now states it outputting 800w instead of its rated 350w - also... with the cli my motors are running hot...

[@michaelbennett1789]

Just bought the x95-v3 and can I fly it with an android phone and a tablet

[@dronejunkie2378]

My motors are 1106 3800 kv , will this time work , should I get 1404 ?

[@ChrisRosser]

1404 is better for this size

[@k4x4map46]

nice!!

[@darkdogg4]

Yesterday i was just flashing emuflight to my V2 and thought how cool would it be if Chris would do a review/tuning video about these 2,5" drones. Thanks

[@artemaminov]

Hey Chris, brilliant work! I waited for this tune! Please point me to dynamic damping setting I can't find )

[@artemaminov]

Found an answer. D Min renamed to dynamic damping

[@johnnyo3947]

Plz betaflight 4.3 tune!!!🙏🙏🙏🙏🙏🙏, I have not found someone who has the tune only you can do it!

[@cityrocker3]

Can you tune the Iflight Chimera 7'' please:)

[@divingfalconfpv4602]

mine yaw twitches on dives. i have raised yaw P too

[@InfinityDrones]

I'm assuming we cannot enable bi-directional dshot and rpm filtering on this drone? When I try jesc, bluejay and bl-heli m it does not detect the escs... Am I missing something?

[@ChrisRosser]

I think this drone has BLHeli32 ESCs I didn't need to reflash them.

[@InfinityDrones]

@@ChrisRosser Thank you for the response. Yes they do have blheli32. So I can just enable bi directional dshot? I saw you didn't enable it in your video, I thought turning it on was a must for all drones.

[@RobinDuckett]

Thank you!!!!

[@owlboy6677]

ESC/Motors Settings under the Motorstab does not show up in my Betaflight Version 10.7. Is this only available in Version 10.8?

[@ChrisRosser]

Yes only in 10.8 with BF4.3 👍

[@tonhabraken9339]

What about 5 bladed props for cinewhoops… would that make sense? I’ve put some on my protek25.. the noise is quite a bit less but so is performance ..

[@ChrisRosser]

It only makes sense if you have the motor to spin it and need a lot of thrust from a small prop. In most cases a larger diameter prop with fewer blades is better

[@michaelhlarsen4856]

Throw them on my protek25 it flies so well thanks

[@DronoTron]

will give a try, but how did you get configuator 10.8?

[@ChrisRosser]

It's available in the configurator nightly repo on github

[@mariobeans]

anyone else have the issue where if you let the beta95 fall too fast its freaks out and revs the motors up?

[@khild]

It's prop wash. Don't go straight down

[@kingjamez80]

Seems like you have an editing error in the beginning with talking about the Nebula nano, motors, and props twice. Don’t know if it’s worth a reupload but it would be an easy fix.

[@ChrisRosser]

Thanks! I can cut it out in YT.

[@madeinhimalayas]

Please do cinelog 25

[@princesfpvdrones]

Wow, I have the 95x guess version 2 and was sooo tired of it I got rid of it!

[@kacpersmx4286]

Is that 1404 4500kv motors version ?

[@ChrisRosser]

Yes 1404 4500kV

[@kacpersmx4286]

@@ChrisRosser I've tested that tune on my cinelog25 frame with betafpv aio and tmotors 1404 4500kv and it flies beautiful ! Thanks again !

[@divingfalconfpv4602]

i thought about squeezing e6000 down inside the holes of the gummy\

[@wearemany73]

Maybe you were a little too easy on BetaFPV regarding the dodgy gyro, great video Sir. 🙂

[@paulfpv]

I have the same quad (but with 1106 motors) and with gyro problems too. Randomly it gives bad informations. I bought it from a friend, I don’t know if I can ask for a free replacement… I’ll try

[@nikotttin]

If you could review one of those tiny toothpick without Blackbox... Then you tell us whether (now how that's already done 😛) the tune feels on to you.

[@aphinion]

After discovering how much fun it is to FPV-Drone around people and play with them I decided a ducted quad is maybe something I might want... so I just got this one and blindly followed your instructions without even testing it before ;P That 19mm cam mount also kinda sold it to me - the first thing I did was upgrading to a nebula pro. It flew really well indoors, let's see what it'll do outside. How is your flight time with 4S 450mAh? I got around 2 to 2,5mins but those where the first discharges of the battery. I hope 3,5mins would still be possible. And gosh that thing is noisy. Once you're done fixing all our resonance issues, you should look into helping prop makers to silence our quads :D

[@PabloDeBiasi]

Cinelog 25 pretty pleeeeeeease!

[@vedrang6146]

# Chris Rosser Review cmw banggod 5"… believe filter tune would be like apex..maybe better!

[@anarkngelfpv]

We got 3 and they all flew like garbage so…I am not sure it is a gyro issue, more likely the design of the frame

[@ChrisRosser]

Did you try clamping the camera plate down with screws?

[@Thunder285]

I guess it is caused by the soft frame. Did the conversion from v2 into v3 and it was a disaster - huge jello on dji cam... Soldered openlager and ended up mounting another carbon layer (v2 frame) on top of it - flew MUCH better 😉

[@anarkngelfpv]

@@ChrisRosser I have tried with hardmounted camera, without camera…I even try adding a 3d printed piece between the motors to make the frame stiffer

[@ChrisRosser]

@@anarkngelfpv Sorry to hear that! Was yours the V3 version?

[@justainchoe6141]

Chris, I know you do a lot for the community, but can you please stop those PeeWee Herman looking open mouth thumbnails? Sorry, I do watch your content and learn a lot, and I don’t think I’ve said anything nice and only given anonymous thumbs up, but it’s just not a good look. I mean, if it’s that’s just you and who you are, then yea, go for it, but it looks sort of forced and just doesn’t look right imo.

[@therunandgunshooter3129]

Thank you!!!