BMW E90 Windshield Trim Replacement DIY (BMW 328i, 325i, 330i, 335xi, & More)

[@mozzeesquiggles]

Im a 60 year old lady, and was told, you have a non genuine windscreen, we cant do it unless we take out the windscreen, and if will break and you going to have to do the whole thing. Went to BMW, we cant do that its not possible, a whole new windscreen and rubber cost about $2000.00. So I watch your video, I have a E325i E90 I purchased a genuine rubber seal from BMW, and I did it my self with a camping spoon as it was thin enough to push down, doing the top first, then the sides from the bottom up and it fits well and is sealed. It looks fine like it was done by a professional. Thank you for saving this old girl $2000.00. The upsell for extra money is just greedy. So far I have replaced the light washers on the bumper, new badge on the back and now the new seal. Next is to replace the struts and I have already bought them. I also have new spark plugs and oil and filters to do my service. Wish me luck.

[@chimborazo328]

👍👍❤

[@bg-se7rq]

Wow, I’ve done this on 4 past bmws… somehow not surprising bmw gets requires for full windscreen replace 🤦‍♂️ 💸

[@infidel900rr]

I admire your enthusiasm, but it might be time for a Camry.

[@mozzeesquiggles]

@@infidel900rr sold that doubled my money bought a land cruiser for the bush

[@JimHardee]

It's much easier if you slide both sides in rather than try to fight getting the C channel around the windshield like he did on the divers side. That's a good way to crack the windshield because on some cars it's way too tight right there. If you get one side slid in, pull up some slack in the center so you can then slide the other side in. Once both ends are started, you can then push down the slack from the center out, and then begin seating the C channel from one end to the other. Also removing is not as difficult as he made it look, but he did figure it out at the end. Just get it started on one side and pull.

[@jasonvargas6625]

Jim, what tools do you recommend for the job? Same ones as original post?

[@FusionR300zx]

Wish I read this soon 😪 cracked mine lol

[@muzzammildeen901]

@@FusionR300zx same

[@stevensims3342]

Just did front and back, cleaned the channel with soap and a soft brush, removed the butyl gunk stuff (it comes on the new seals). Slid one side in, then the other, made sure they were even and it went into place super easy. I even filled some small spots where the paint had been rubbed off or something with some similar color rustoleum. After pressing it into place, peeled the double-sided tape cover and gave the seal a massage. Thanks for the pro-tip.

[@GoFastGator]

Bend the new seal slightly, like a bow. Slide one end in, slide the other in, and press the rest of the seal into place, the ends will push outwards as the middle seats into the channel. Done. Once you’ve done it once, it’s a 10 minute job. But then I hope my new seals last long enough that I forget how to do it!

[@mikefisher6623]

This method works perfectly. Thanks Brian!

[@AaronRadfords]

Just did the same. The FCP approach doesn't work, tried it a few times then guessed your approach. Perfect result.

[@pepitopepito2967]

FCP surely made it look easy but his method was almost impossible in my 330i e90. you’re pro tip was much easier. i may also add, using some soapy water or windex and a plastic trim tool makes it even easier when pushing the rest in that tight spaces

[@Bimmerfan_e36]

This was a great additional tip. I was struggling with the other end! Thanks a bunch!

[@gcwposs]

This will sound backwards, but FPC Euro makes me want a BMW. Having a resource this good is rare. A parts supplier and educator all in one. Well done.

[@grady.stu.8300]

The urethane that holds the windshield in does not deteriorate. That's why car manufacturers use it. Those moldings are only cosmetic. The only thing that can break the seal over time is rust. It's annoying when people say incorrect info on their channels. Still gave you a thumbs up though. Lol

[@FPSAnarchy]

it seems i am leaking water from where the piece is missing on passenger side, could it be sunroof drain clogged?

[@LouMires]

It does look a bit tedious, but you did a great job explaining and guiding to where I feel quite confident to do this myself. Thank you! Grateful for all of FCP Euro's videos. Already started ordering parts from you guys.

[@fcpeuro]

Thank you for watching Lou, this is why we do it! Happy wrenching.

[@mikelodes5187]

Best video of the bunch. Thanks for the extra time to show the steps.

[@jeffreyhinman1397]

You can slide both ends in first then do the center of the seal. No need to pull the side trims off the front.

[@SterlingCooper21]

Great guide, but what was the degreaser/solvent cleaner that would be recommended for this job?

[@AndrewRappL]

I had a much tougher time removing mine on a 17 year old e90. I had to use needle nose to pull it out after removing the crumbled parts. I actually snapped off my 90 degree pick. Definitely put both ends in and slide towards the end as others mentioned. I parked the car in the sun to heat it up and it slid in quite nicely. I rolled it with a nalgene bottle to get it fully seated. I pulled the entire tape at once and worked it in with gloves. Overall an easy job with a little work to remove the old one

[@UnJustAF]

Rip to my windshield o7 that metal c channel put up a good fight and ultimately I cracked the windshield. Even with a few microfiber towels. I’m really surprised it was in as tight as it was, there was no molding left above it and water was getting in. Well safelight said they could be here tomorrow. Plan b it is

[@b20teamunknown]

How much was your window replacement?

[@mohamedeltawab]

The sliding trick was amazing! Thank you!!

[@fcpeuro]

Glad it helped!

[@bmwbydesign1590]

I really like how the camera is so far I can’t se anything 👍🏼

[@iLuminaLighting]

Do you have a video for Lower Windshield Trim Seal Replacement DIY for 2008 E90 sedan?

[@fcpeuro]

We do not, but we could certainly do one!

[@garygrenier]

Wow, STUNNED by how bad that trim is. Nice Job Nate and FCP!!

[@wouterclaes]

At around 03:00 mins the metal rail is taken out. Why was this done? Does it not need to be retrofitted afterwards? Just asking before I start :)

[@KERO_FL]

Just cracked my windshield while using a screw driver to remova old one. DO NOT USE SCREW DRIVERS AT ALL.

[@brandonbogart7195]

Great Video. All videos on KZbin of windshield seals are only the top seal. I wonder why only a couple on the lower seal and windshield cowel, which water also takes the easiest path and to the lowest point.

[@2468xx]

Bummer that you don’t show any close ups of the seal. I ordered one via Amazon and cannot get the C channel to fully slide into place. Tried 10 different angles on my 2006 325i. It’ll fit on the ends but will not go all the way into place in the center. Cheap part?

[@VolkanSoyler]

Thank you, i apreciate, my e90 318d too !

[@sonicnofadz]

probably a good time to pull the roof mouldings and respray those as well

[@ryankaiser3104]

Literally just finished mine🥵✨😭

[@armourbl]

What about the lower trim. Mine is falling apart but can't seem to find a replacement.

[@danrucker9902]

What was the degreaser solvent that was used in the video?

[@mikecolby2951]

So i just received this part, and it was completely folded in half. Now the rubber has waves in it that won't flatten out. Is this how these seals are normally shipped?

[@thivesennayager6278]

Just what I needed

[@TheLoneRanger1992]

Why do ppl say you can crack the windscreen? How would it crack? When you pull that trim out?

[@robertgray6512]

I like the Benny Hill sound effects.

[@uncoturner]

could you show us how to remove the roof molding rails without breaking the clips? i see the paint has failed on those with this car also. thanks!

[@godfatherofcinema]

great video. now to get this crappy thing changed. Thanks!

[@DrNeo_The1]

hi QQ is the windshield for a 325i 2012 same as the 328i 2012? can you help im in mexico :)

[@hellblast911]

Had mine replaced under warranty. Now it's years later and time to do it again. Rear was very easy, like it should be. Front was borderline impossible because I've had the windshield replaced once. So much glue under the window that the c-clamp will never fit. I'll redo the rubber trim when i get a new windshield. Until then, passenger side is a mess.

[@zuc3sal]

Perfect instructions. Thank you.

[@kevincourtney473]

Great video thanks. I purchased a genuine BMW replacement seal based on my chassis number and it was all going fine from the slide across at the start but as I got to about half way through I was having a lot of trouble getting the c channel to seat itself on the windscreen and almost to the point that I thought the product was faulty. In the end, after at least 1 hour of pushing and tapping with a nail counter sink tool and using the Terri cloth with my hammer I had to give up as it looked like crap and was getting no where. My question is should I try to use something like a tiny bit of RP7 in the c channel to help it slide on or will this cause some problems late on? Appreciate your thoughts?

[@michaelgordon3434]

Would applying a small amount of heat with a heat gun prior to the removal of the old seal help? Or would it be unnecessary.

[@BeverlyHowell]

This part on my 2004 BMW 325i looks fine, but the BOTTOM of the windshield molding (rubber strip) is cracked badly and leaking. What product do I need to fix that? Thank you in advance!

[@fcpeuro]

Hi Beverly, more than likely, your windshield cowl needs replacing/attention. Feel free to reach out to our team @ [e-mail] if you cannot find what you are looking for on FCPEuro.com

[@Kaindingo]

@@fcpeuroany chance you can do a video on the lower windshield seal? Haven’t seen any good videos/instructions for replacement.

[@colinwahl2509]

Rear seal next? What about the roof rain ditch moldings? God bmw dropped the ball on this car's trim.

[@brandont1799]

kzbin.info/www/bejne/fXaZaqF8bd6Xpac Here is the rear window trim. I love this guys channel and use it for all my e90 diy’s.

[@modularformsboy]

It's much easier to insert the new rubber with a wide trim tool like you might find at harbor freight. No hammer needed, no risk to your windshield.

[@sebastianj4549]

Where can i buy it?

[@TheDomin8rr]

I have a similar issue with a '05 Mercedes E320 but it's the seal between bottom of windshield & car body. Is there a replacement seal available for the bottom of windshield?

[@slscamg]

This looks like an absolute PIA. If I had an E 90 I think I would just pray my windshield cracked and had the insurance company repair that seal lol

[@charlesbcraig]

Agreed. I just had my Indy shop do it two months ago on my 2007 328xi E92.

[@onecookieboy]

A sharp smack with a dumpy hammer would expedite the replacement of the windshield!

[@itsdanielrosa]

Please do this w211 e63 for the bottom windshield trim

[@angelsoto2194]

I had to replace my windshield because I pulled in the seal to hard when taking it out. Job ended up costing me 300 smackers

[@sandrajones9654]

Thanks very helpful

[@stephenlishman4750]

How much is a genuine seal from bmw in £

[@86FxBdyCpe]

thank you.

[@fcpeuro]

Thank you for watching, Steve!

[@hehecheesy]

any tips for the rear glass lower trim? i replaced it but it keeps popping out at the corners

[@fcpeuro]

Hey Chris, you can try and use a little bit of heat to make the seal a bit more malleable, and combined with a trim tool you should be able to get it seated a little better.

[@chrismagana16]

Real question, if it were to crack again do we send all the crumble pieces back for a new one under the lifetime warranty ?

[@fcpeuro]

100%

[@araujojunior4736]

Você teria o código dessa peça? Obrigado

[@TheTechy2]

Is this the same as the e93 vert?

[@fcpeuro]

The process will be similar, however, the seal for the E93 covers both the top portion of the windshield as well as both A pillar sides. Part number 51317150646 available on FCPEuro.com with images!

[@CastroJordan]

Same for f3x?

[@masonthomas8210]

Would the same part work on a E90 320i? I know it isn't listed in the comments as a working model but praying it would still fit

[@fcpeuro]

Yes, I believe the only reason its not listed is because that it not a US/North American Market model, but since its an E90 it should be the same part!

[@masonthomas8210]

@@fcpeuro Thank you

[@Eck0es]

I recently replaced my windshield so they replaced the dry stripping so its good as new. But now the problem is my back rear window corner stripping which have deteriorated away and now the corners are pretty much exposed. Hope you guys have a solution for that

[@ryderlehmann2366]

Would this fit a 323i 2009?

[@fcpeuro]

Hi Ryder, while we did not get the 323i E9X here in the states, the idea should be exactly the same. You can cross reference part numbers on a site like bimmercat.com

[@OndroFe]

what a fucking job, cracked mine on both sides

[@TheTruelakersfan]

I must of got a bad part cuz it took me 2 hrs to force that crap in and it still didn’t set right in smh

[@justpeachie26]

Weird, if you contact FCP Euro’s customer service department they will tell you this part should be installed in a shop because the glass needs to be removed for proper installation 🤔🤔🤔

[@vo.nnie__3551]

I cracked my windshield 😭😭

[@nikolamakedon8681]

5 euro from ali expres for two minute is changet

[@Lup3r]

"Do you see how I'm hooking it to the windshield at 90 degrees?" No literally both of your arms are blocking everything we're supposed to be seeing. You have a whole camera man yet you don't move around for a better shot..

[@AX5Z]

Don't do this unless you have a spare windshield.

[@adamk5436]

if you do not want a new windshild, I advise against it

[@thooke222]

Did yours crack?

[@mattyice2099]

Everything was fantastic but working with your ring on made me cringe a little sometimes lol

[@fcpeuro]

Time for us to buy all our team rubber rings!

[@MangoSpringroll]

e9s takes way more work than this.... T_T Just did mine today, sides aren't perfect..... but better than chipped away rubber.....

[@enedifanovaha7713]

Bro you need to move up your camera on first half your video

[@NicoDelCap]

This a job

[@jonbrown9641]

Why put the trash on the customers car though?

[@metteojacobs6422]

Alsome

[@fcpeuro]

😎

[@michaelf9875]

Yeyeye