BMW f25 Trunk won't open , Problem Solved !

[@mohammedsabah2887]

Keep going bro Good job from Iraq Baghdad 🇮🇶🇮🇶🇮🇶

[@kul_thum]

Nice and fine work. Happy to see your smile when work is done 🎉🎉🎉

[@MOvidiu]

Always!

[@piotrm_____y9457]

Kolejna dobra robota lubię oglądać twoje filmy ,pozdro z Polski :)

[@MrHdsource]

Thanks pal!! Fixed my f36 after watching thisn

[@mick32156]

Thank you so much. Just completed this job on a 2016 X3 F25. You saved me a lot if money. God bless you.

[@almariodon7599]

Did you have to calibrate them?

[@mick32156]

No. It was easy. Biggest problem was supporting the tail gate whilst swapping over struts. My wife held it up.​@@almariodon7599

[@Hillbeley]

Great video, it helped me change my RH Powerise by Stabilus. My symptom: the tailgate would not latch and there was a crunching noise on the RHS of my 2016 F25, the tailgate was being pushed over to the left (actually being pushed down on the right), but there was no error coming up on the scan by my icarsoft. After changing and dissecting the strut the spring had disintegrated and the cover was beginning to bulge at the hatch end. I should have changed it a lot sooner and I would have if I knew how easy it was. I don't think I had to initialise the strut, the open circuit error only appeared when I disconnected the original strut. Thank you.

[@astrolazer]

Excellent video. Very professional. Thank you. My x3 does same thing. Opens 4 inches and then shuts. Sometimes it works correctly. Most of the time it does not.

[@JohnRambo-e1t]

Отличное информативное видео! Спасибо! Искал не долго!

[@user-xw6vl4fk2e]

Thank you very much for this helful video :) Do you know if there another means than ISTA Plus (that I don't have) to initialize the system after strut replacement? Is it possible with bimmer tool or icarsoft or with another OBD tool at a moderate price?

[@pablomesias7936]

Good Job my friend I changed my self bat only sound clicker then I have to pulled up manually probably the auto Zone sélleme only the one manually bat I gone doble check again or maybe my X3 xDrive 2,011 don’t have that cane of shocks bat thank very much was Exelent God Blessyou

[@johnmac8084]

You are very thorough, good job 👏

[@MOvidiu]

I appreciate that!

[@DavidHernandez-lf6hf]

Very professional quiestion : if I don’t have the computer scanner , still work when I just replace them, just by start the car on and off ??

[@MOvidiu]

Hello! Some times will work but most times will not work!

[@andreutobaruela1775]

Subtítulos en español seria posible asi los que no dominamos el idioma disfrutariamos mas de sus videos,gracias y un saludo desde spain.

[@rami587]

i would like to know the brand you have fixed for the lifters

[@hekurans1337]

Great video! What is the original number for the part?

[@MOvidiu]

Hello , for parts number use Realoem.com

[@kouiderakfa9583]

Hallo I have the same problem Do i need ista plus after change ? And what of adapter do you use for ista thanks

[@MOvidiu]

Hello . after replacement the system will need to be recalibrated !

[@leiflillandt1488]

​@@MOvidiuDoesn't it calibrate itself when you first close it by the hands and then drive it electrically a couple of times? Yesterday I changed the battery in my 2011 F25 and got some fault codes, for instance with the co-driver door window. After driving it a couple of times from bottom to top I could get rid of the fault code. But there were, IMO, some strange noises... Maybe some kind of grease is needed (as a first step).

[@leiflillandt1488]

After reading another answer further down, I can see your point in your answer. And after all these struts are not quite cheap.

[@PeterPan-gd3nh]

Hi great video. I need to replace the RHS strut on my BMW X3 F25 2016 model as it is cracked. A please advise me if the steps to remove struts and trimming the same as your car? Is it a must to replace both sides in one go?

[@MOvidiu]

Hello ! is not a bad idea to replace them both .

[@gusahcollins2980]

Good job 👍

[@harrisspiliopoulos7281]

I bench tested the strut and now the motor works but they do not open or close and the gear inside just makes a sound. Is there a way to reposition them ?

[@MOvidiu]

Hello, go and see my other video with the teardown of the strut

[@rustamabdualiev]

Enjoyed watching, keep going

[@MOvidiu]

Glad you enjoyed !

[@bobbypersaud]

I have problems with my BMW X5 e70 when trunk is closed it won’t open inside or outside or with the key fob I hear no noise trying to open but when I release it it closes fine with key fob and inside

[@MOvidiu]

Hello ! possibly the lock on the tailgate is defective, it will have to be disassembled and checked ....

[@bobbypersaud]

@@MOvidiu Thank you for your reply it’s band new tailgate latch

[@khyrofilms]

NIce job again. Clean simple. Regards. ;) The "special tool", hammer required ;) ;)

[@MOvidiu]

You got that right! :))

[@ied3vil]

Hey i also have the same special tool, i use it to push the brake when the car is on the lift as well :))

[@MOvidiu]

Best tool ever! 😀😃

[@Reema62ish]

Can I ask where you ordered the pair of parts from

[@1974issacc]

Do you know if this would help fix a Hall sensor issues in the rear struts.

[@MOvidiu]

Firs check the tailgate control module for water damage. The si module is ok. Replace the damaged actuator!

[@alinematheus4483]

I changed the module and after a period change the struts too, for new ones, and it is not working again now. I only heat a click sound, but dont move up or down nothing, only click sound near to the car battery do you know what can it be ? Module failure or strunt failure ? something else ? thank you

[@РахимШайбеков]

👍👍👍

[@simonhaugenkolstad8561]

Do you need to run it in service mode the first time with ista? I im gonna change mine. Dont have ista.

[@MOvidiu]

Yes ideally is to be calibrated!

[@Ovidiuirimies1906]

Buna seara!Am o problema cu deschiderea haionului electric la bmw f34 .Tin sa mentionez ca am schimbat iala, motoras modulul electric pt portbagaj ,se deschide doar manual portbagajul actionand de un cablu din interior.Inchiderea portbagajului functioneaza ,atat din buton, cat si de pe cheia masini .Credeti ca ar putea fi de la unul dintre telescoapele electrice cu gaz ,multumesc mult.Cu stima Ovidiu

[@MOvidiu]

Salut, sfatul meu e sa apelezi la un service specializat BMW din zona ta pentru o diagnosticare completa, asa sa arunci piese doar ca presupui ..e o pierdere de timp si bani !

[@iosifatnichifore9746]

Foarte profesionist. Este o mare placere sa va urmaresc. Unde in tara aveti atelierul? Am grand tourer 218d 2016 150 hp. Datorita faptului ca sunteti cu adevarat un meserias as vrea sa il aduc la dumneavoastra pt un test sa vad ce are

[@MOvidiu]

Super tare , ma bucur ca urmariti acest canal , nu e Atelier e un studio :) , dar din pacate nu va pot ajuta ,pentru diagnoza si reparatii apelati la service-urile specializate BMW din zona dvs ! Multumesc pentru interesul acordat !

[@harrisspiliopoulos7281]

Where is the control unit located ?

[@MOvidiu]

Inside of the trunk under the floor panel on the left side of the car

[@harrisspiliopoulos7281]

@@MOvidiu Thanks! Do you know if there is a pre wire if the car does not have it factory installed ? So if i buy the module and the power lifts can i install it ?

[@MOvidiu]

Unfortunately they are not pre-wired

[@harrisspiliopoulos7281]

I have 2 strut. They have 5 wires. Red-Black signal and 2 more. When i connect the 12+ and negative the motor clicks buy does not turn. Do i have to connect any other wire to bench test them ? C an you help on this

[@xTRAFFICANO]

Need the link for these replaced

[@MOvidiu]

Any car parts store! Online or phisical at the counter!

[@Shamshirkhan209]

Hi, Could you tell me what is the name of codereader you use? Thanks! :)

[@MOvidiu]

hello , is not a code reader is original BMW diagnostic program IstaD

[@BadBoyNK]

good job man ;)

[@MOvidiu]

Thanks!

[@BadBoyNK]

if you just change them and don't do the initialization with ISTA the car will be able to recognize the new ones and work properly ?!

[@MOvidiu]

They will work but it is possible to destroy them, because the initialization will make the computer learn the strokes of the new telescopes and will stop almost the end of the stroke, if not, it can be forced every time it is opened and at some point it will break

[@BadBoyNK]

cheers for the answer

[@kartlomedia7360]

super 👍👍👍

[@MOvidiu]

Thank you! Cheers!

[@codingbmwsofia2818]

special and magic tools haha :) again nice video ! :)

[@MOvidiu]

Thank you! Cheers!

[@alexandraava3034]

Esti maxim

[@claudioagmfilho]

Are you sure you're not Dracula with that accent?

[@lnalbandyan]

drive unit part number would have been helpful

[@MOvidiu]

Hello, realoem.com

[@manoo422]

Pity you didnt say how much those units cost!!

[@LGonera]

Your trunk opened tho, this video sucks cause you just pulled your handle three times and it opened, doesn’t explain anything if the door will not unlatch

[@محمدنصر-ع2ه]

❤