BMW F800 S ST GT Drive Belt Replacement EASY

Join this channel to get access to perks:
/ @thebmwguy
BELT DRIVE BMW F800S, F800ST-
bmwpartsguy.co...
Belt Drive BMW F800GT, F800GT-
bmwpartsguy.co...

[@ianburton518]

BMW f800gt 2017 Just purchased new belt ready for change Great video useful info 👍

[@canlam5697]

Do you have instructions to remove the front wheel?

[@ridethroughlifertl]

This video is pretty old now, but please see this. I'm trying to get the eccentric out of a 2013 F800GT and just cannot figure out how it comes apart. It looks like it has a retaining bolt keeping the whole thing from coming out, but there's no way to loosen that. Even turning the eccentric to its loosest adjustment doesn't leave enough room through a wheel stud hole to get a torx bit in there. Please help.

[@Silverfoxmike22]

Very helpful video thank you

[@TheBMWGuy]

Glad it was helpful!

[@rolandbaranov3546]

Thank you for the vid. Let me add few points (1) the tension check should be done with the bike on its stand and the rear wheel off the ground (unloaded) as belt tension increases as load is applied to the rear suspension (2) use a cable tie wrap (or similar) to apply 5Kg (11 ponds) of downward tension on the middle of the lower part of the belt (normal deflection should be around 32mm) (3) the blue dot/mark 7:37 does not make any sense to me unless the rear pulley is oval which is not the case on my motorcycle nor I have the mark. (4) I found on a BMW forum the follow which makes lot of sense to me: "As you sit on the bike the belt gets even tighter. I sit on the bike and twist the belt where it is exposed just behind the rear brake master cylinder. I set the tension so the belt will twist to 45 degrees from flat with a reasonable amount of pressure."

[@wavydavy9816]

BMW charged me nearly £500 for this job (£240 for the belt and £240 for labour) because the book says you have to dismantle the whole rear end of the bike. When that belt broke (after about 5000 miles) I went to they guy down the road and he fitted a new (non-BMW) belt for a total of £150 (£120 for the belt and £30 for labour) because he put it on as per video (which may also _actually_ have been the way they did it at BMW). The belt is still on there and in gwo 26,000 miles later

[@shammon1]

Fantastic at last a proper belt clip for the F800ST, PLEASE do a F800ST front fork seal change and rear suspension spring change its a must for all us F800ST owners, thanks

[@Sweep29]

Dont forgot that the F800ST has a different length belt than an F800GT so the info you state in the video is incorrect ie one belt fits all F800's.

[@TheBMWGuy]

in the description I have both belts, I said this procedure is the same for all f800's.

[@sympathic21]

@@TheBMWGuy which is also wrong, f800gs does not have belt :D :D just messing around, cheers.

[@Hectorladron1950]

I’m doing the replacement of Drive belt in my f800 st.

[@TechnMoto]

Well done. I just purchased a 2012 k1600 and am loving the content on your site.

[@brandonbeattie5885]

Do you know where I can find fairings for 2007 f800s?

[@jl9161]

Good tutorial except it is still very vague how much tension the belt should have...😅 Could you specify a range of free play?

[@RG-500]

Great tutorial. Thanks for posting it. I own that exact bike even in the same colour.

[@MartimTeixeira-i4l]

Many thanks

[@petecurran3995]

Excellently done, sir! BMW have made this a logical and straightforward process. I'm looking at a MY 2014 model and the seller wasn't sure when the belt was last done. Thank you!

[@mohamadsadi7612]

Thanks

[@bestione761]

Hi there.... great video for us, bmw f800st owners.You don't say nothing about silentblock replacement which has to be done when you repalce the belt. Years ago I had my belt changed by my bmw dealer, some months later I realised the crown was moving by hand and the belt was not in the right place. I went to the bmw dealer after cheking the bill and at that ponit I saw no works were done on the crown. The dealer asumed their mistake and changed the crown silentblocks. Since then everything works fine again, belt on place and crown without slack. I opened the crown every two years just to check it and to put some grease to avoid that anoying "old bed spring" sound. Woud be great a valve clearence video, that would be my next chalenge😂

[@guillaumetaillefert]

Thank you very much! I just finished, everything’s ok except that I can’t adjust, I don’t have the tools and I’m afraid the belt is too loose. Is it possible to drive though? or is it too risky ? I just have to drive 20 or 30 miles before going on Monday to a bmw store for them to adjust.. Thanks in advance for your reply 🙂

[@TulaneAve]

I was hoping you'd give some tip on what tension to try to get on the belt.....like "5mm of deflection" or something, but no. Darn

[@memduherdemisik7805]

Good job bro

[@crankicurmudgeon746]

This is one of the best technical videos I have ever seen on Facebook. I happen to be buying an f-800 ST which only has 6,000 mi on it so I don't really need to do it for a while but I was curious about the process. This was crystal clear it was well paced and the video and camera work was excellent. If I do pick up this bike and end up actually riding it I will certainly subscribe to your channel Have a cookie 🍪

[@jelmerdejong5126]

Rear wiel bering eccentric bmw f800ST bj 07 Type nr ? 1 & 2 ???? Help

[@rubberban]

Thanks for the f800 content. I have a 2011 st. Would love to see you do a set of tires. You think it can be done with hand tools?

[@christianhagemoser3800]

Are there LED headlights, indicator road legal to purchase?

[@jamiesanfilippo8729]

Excellent, clear and concise. Thank you from an F800ST owner!

[@jimbeamm36]

It's my understanding the F800ST belt is shorter than the F800GT belt. Anyone know for sure?

[@TheBMWGuy]

can confirm, they have 2 different part numbers

[@briansmyth905]

Thanks for doing that, clear and concise, well-done!

[@ArneBruneOlsen]

Could you please send me the instructions on how to change drive belt on F650CS 2002 model?

[@TheBMWGuy]

join my channel under platinum level and e-mail me

[@DukeOfEarle]

Excellent. I subscrived and need the manual section for flywheel remove and install. How can I get that?

[@TheBMWGuy]

E-Mail me, my e-mail is on the member page.

[@petermosdell580]

I’m a new K1600 owner. Would love to see the correct way to do an engine oil change 😉 Thanks for considering

[@TheBMWGuy]

take a look at my channel boss, i have already done this video

[@demiratmotovlog]

Great work