Bobcat interlock control system, failure and fix/override. Do at your own risk.
Пікірлер: 21
@frankrodriguez52022 жыл бұрын
That info is priceless to get it back up. 👍👍
@MitzvosGolem15 ай бұрын
Did this on a new Holland. Overide computer garbage . Excellent 👍
@Joe-wy2bn10 ай бұрын
I'll probably have to do this soon, thanks for the info.
@kee_b2 жыл бұрын
You're a bad man! I wish you were in GA!
@sealerking196810 ай бұрын
I was having very similar issues and my alternator was going bad. I replaced it and everything works perfect. It was causing the BICs to shut down.
@osd3218 Жыл бұрын
Hello Love you Your video tutorials I have S100 Bobcat loader ,was working fantastic until last week when decided that the auxiliary pipe won’t respond when trying to use grab bucket , the bucket opens but won’t close and to close I have to release the pressure by loosen one the ram pipe and that way it will close by pushing down by hand then Tightening the pipe back it will open but it won’t close any idea what could cause this ?
@affordablerealestate81693 ай бұрын
Bobcat t190 one flash on the BICS display for lift tilt, cannot lift or tilt bucket, machine stuck Without putting 12 volt to that circuit, the error is "hydraulic lock valve open circuit" I put 12 volts to the BICS circuit and it started to flash twice for, "valve output circuit shorted to battery voltage" How is that that in this video, he puts 12 volt to that circuit, and it works? Bobcat says that BICS circuit is less than 12 volt, I am getting 4 volts on the BICS circuit when I push the button to put the password (before starting) Someone please help
@MitzvosGolem15 ай бұрын
Aux solenoids run off pulse width modulator 9v from BICS . Don't leave 12v on Aux to long will burn them out. Momentarily open close bucket should be fine. Main Bucket boom run off 12v.
@michaelbartels19405 ай бұрын
Been a couple years and still running strong.
@MitzvosGolem15 ай бұрын
@@michaelbartels1940 we did this on a 1999 763f still no auxillary hydraulics. Have boom bucket and drive Stems may be stuck ? All coils read 10 ohms . Grounds power to green by passing switch in handle. Pilot pressure actuates aux on this non ACS unit.
@affordablerealestate81693 ай бұрын
Yes, I am diagnosing now a T190 with lift tilt one flash I put 12 volt to that circuit, then it flashed twice for "circuit shorted to battery voltage" How is it that in this video, he puts 12 volts to BICS circuit and it works? "main bucket boom runs off 12 volts" I am getting 4 volts on the BICS circuit when I turn the machine on to put the password, before starting engine Let me know where I am incorrect
@MitzvosGolem13 ай бұрын
@@affordablerealestate8169 bypass BICS . Connect to aux solenoid s to a new remote switch fused . Ours works now.
@user-qd1vu2nb7l Жыл бұрын
Hey Mr Mike I have a bobcat 753 seat sensors shot The lap bar sensors busted and the traction doesn't click the solenoids I need help if you can
@youcast3 Жыл бұрын
Can you message me a simple way of powering the auxiliary solenoids and at the same time being able to control them with my thumb switch
@youcast3 Жыл бұрын
Hi Mike I'm having trouble with my bobcat 763 f. I am not getting power to the top two auxiliary solenoids
@danielmuletas9786 Жыл бұрын
Ora. Compa. Jesús. Ya arreglaste el tuyo. Tengo el mismo problema con el mio pero.
@ashbyfarms2 жыл бұрын
Hey Mike I'm trying to do the same thing to my 753f. Is there any way I can personal message you on Facebook or something
@michaelbartels19402 жыл бұрын
Ya that’s fine my Facebook is Michael Bart, I am in Belvidere IL.
@youcast3 Жыл бұрын
I found this very education I need someone clarification on part of the video is there a way to communicate with you? p
@MrDpl096 Жыл бұрын
@@michaelbartels1940 Having trouble finding you on Facebook. I have a 763 with this issue. I have a couple of questions if you wouldnt mind answering. Thank you for sharing the video;.
@MrDarkoKos9 ай бұрын
@@michaelbartels1940im trying to do this to my bobcat 863, but i cant follow your wiring. Any way you can do a drawing or i can contact you?