Boiler Service - Ideal Vogue Combi Boiler Step by Step Guide - Leeds Plumber

[@a12345ok]

Cheers Allen Top video I like the boiler the display is spot on nice and easy

[@AllenHart999]

The new Vogue is said to have a better display although i haven’t seen one yet. Thanks.

[@anthonymaddock6442]

@@AllenHart999 hi Allen im 56 years old and am really considering a career change and going into fitting boilers I'd love to know how to get started in this business I do have age against me I do realise, but I'm a young 56 and not too old to learn..do you have any ideas has to how I could get started in this business?

[@cianpapazian]

Cheers Allen. Nice to see a service from start to finish. Tomorrow is my final exams before I become qualified after 51/2 years of doing an apprenticeship.

[@rickysheldon4355]

I love your videos honest and quality education can't beat it Sir thank you. Hope Mrs H is getting better.

[@AllenHart999]

Thanks so much

[@stewben1169]

An excellent Video you can definitely see the reasons for using pressfit when installing a new boiler.

[@AllenHart999]

I love using press fit. Thanks.👍

[@ReferenceFidelityComponents]

Brill boilers. Just had one installed and got to say the Ideal Vogue is a quality piece of kit and worth the extra over the newer WB Geo line.

[@MrPaul1f]

Great video Alan, Ideal Vogues are top quality, the display is particularly well though out on these.

[@AllenHart999]

👍👍👍

[@wazkayani]

Very impressive. Wish every Engineer was as thorough as you!

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@32dartsking]

good vid Allen, i love fitting these boilers i think they are the best on the market for build quality, ease of fitting and servicing and the display is second to none ps i also like the fact it has a pressure gauge on it.

[@AllenHart999]

Right on

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@Mike_5]

Proper safe and legal workmanship not the cowboys you can sometimes get - nice one Allen for sharing this top video

[@AllenHart999]

Hi Mike Thank you so much for taking the time to comment, Also your kind words..👍

[@allum007]

Excellent thorough service. Not normally seen nowadays . I'll be definitely be using the service bag idea for analysers etc .

[@AllenHart999]

The bag is really good. Thanks for watching.

[@gjmheating8857]

Allen you said about efficiency level you can get that High by lagging all that press fit you can also get it higher by range rating it but I'm not sure you can with vogue

[@AllenHart999]

You cannot range rate a Vogue unfortunately.

[@umarg06]

Omg I didnt realise you can get the gas inlet pressure and combustion at the same time Allen you are a DON thanks man

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@peteobrien7614]

Another great video Allen. I’ve bought myself a Vogue Max System 26 which I’ll be installing once the heating season is over. I can finally retire my faithful and reliable 30 year old Potterton Netaheat. Hoping to donate it to my local Assessment Centre as it’s a positive pressure fanned boiler as you will know.

[@AllenHart999]

Thank You

[@michaelstott734]

Another top video Allen. You are so generous with the sharing of your knowledge. Thank you.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@markhoward5780]

Really enjoy your videos , done a bit of plumbing back in the day so I am interested in the new ways of install and technology , keep them up . howy

[@AllenHart999]

Thank you so much for watching Mark. 👍

[@tokomac7728]

great video and very simple explanation just little note on expansion vessel checking.I always first check with system topped up before pumping up air tu be sure rubber belly is healthy Again very nice and clean installation 👍

[@AllenHart999]

You cannot get a reading from the expansion vessel when it's filled with water. Thanks.

[@alimack5489]

Love the cheeky drain off down the bottom Allen

[@AllenHart999]

You can just do it from filling loop but I didn’t want to splash the boiler too much. Thanks.

[@jayhambleton5834]

Excellent video Allen

[@AllenHart999]

Jay Hambleton Thank you 🙏

[@jackglossop4859]

My boiler care routine involves thanking it for its hard work every time I get something from the loft and promising that I'll get it serviced next year.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@BearB2186]

This comment didn’t get the recognition it deserved 😂

[@54FEER]

Hi I saw your videos and I really enjoyed it keep up the good work. I have a Main Eco 30 Combi boiler I was fitted about 7 years ago, the whole pipe work is new and radiators. There is one thing that annoys me on my boiler is that when ever is ignites it makes a small tiny explosive noise you can hear it from far 😫 I have so far replaced the electrodes since it was old and bent (it was working but I wanted to avoid it failing), the heat exchanger was hoovered and the seal was replaced, the diverter valve and actuator was replaced (since a small leak damaged it). I have regularly flashed the water out using the drain point and running the boiler and keeping an eye on the pressure (the water is never too dark and flush it until it is clear water, I added some inhabitors, clean the filter out and took the air out of the rads, it is well balanced too. I had to pressurise the extension vessel which is good now, on the same time I took the prv out and cleaned it very little dirt on it it’s working good, I also cleaned out the part in which condensation and other dirt accumulate. There is one thing that annoys me on my boiler is that when ever is ignites it makes a small tiny explosive noise you can hear it from far 😫, you could describe it like a small delayed ignition 🤷🏽‍♂️ What would you recommend to check?

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@peterryan7827]

Alan, i have messaged you before, about boilers, and the extension that we are having built right now, anyway the builders said to me you pick any boiler you want and we will fit it for you, so i chose the ideal vogue, i hope that your ok with that one as it now comes with 12 years warranty i am told,it will connect to 10 rads ,but we are just a 4 bed semi, and as a fan of you and your work i thought i would check out my decision with you before buying, Ps its not a combi, we have a 36/18 prelagged, Thanks again for all you video,s

[@AllenHart999]

peter ryan The vogue is a very good boiler in my personal opinion.

[@garygormley3842]

Really informative videos.do you do a earth loop test at the service? Get yourself a regin pump for the vessel's they have a really long hose on them.

[@AllenHart999]

Thank you Gary.

[@maxnavsa4470]

Brilliant video Allen. I've got an ideal ISAR, it's nothing but trouble. I don't think I could ever go back to ideal. No matter how good they are now. Never in a month of Sunday.

[@AllenHart999]

Lots of really good boilers these days from all brands. They just need a good installer. Thanks for watching.👍

[@elwittinio2865]

The ISAR was awful,fitted one in my old house. Ideal are good now, every manufacturer has a bad boiler somewhere in there history. That ISAR was bad though 🤣

[@bobby76353]

Thought the whole purpose of these boilers was not to need an annual strip down unless you had a problem? Seems a bit overkill, and the cost of replacing the heat exchanger seals an unnecessary cost to the customer. That's what Baxi taught me.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@romeomeoful]

Hello to all engineers out there, and again a massive thank you to Allen for an amazing and thorough video. I have a quick question how long does it take for a engineer to complete a full service? thank you for all your answers

[@Liam_Hirst]

Anything from 30 mins upward There’s some boilers we work on regular and can have stripped down and cleaned in no time

[@nomore5668]

Another great video. Thanks Allen.

[@AllenHart999]

Thank you.

[@elwittinio2865]

The Vogue is the Daddy of boilers, love em.

[@AllenHart999]

Definitely 👍

[@lostinthoughtscalminsilenc8167]

Why do you pump expansion vessel?

[@AllenHart999]

Because it looses its charge.

[@bluedwarf8858]

Hi Allen, do you gas rate on a service and if so do you put it on high fire to do that

[@AllenHart999]

yes

[@miransalih1079]

Another brilliant tutorial Alan, lots information nicely explained thanks man you're awesome 👌🏻

[@AllenHart999]

Miran Salih Thank you so much for your kind words 👍

[@muradkhan6787]

Excellent information video ❤️

[@AllenHart999]

Thank You

[@michaeldavis9095]

Alan you mentioned that the Vogue has all brass fittings. Is that the case with newer vogue boilers? I had a Worcester and the failures I have experienced are with plastic components. I will buy a vogue if hey still have all brass fittings. GREAT VIDEOS

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@abdulh63]

Hi Allen. What was the name of the socket set with the ratchet? Great video again really helpful thanks

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@PaulHVAC1]

Hi Allen Great video. Did i read your anylizer correct as it appeared to show (21:44)on Max fire 159ppm of CO. Is 159ppm considered acceptable in the UK?

[@AllenHart999]

As long as its less than 350ppm, Thanks.

[@johnpotts2276]

can you use press fit in inaccessibly locations

[@AllenHart999]

Yes, Depending on the manufacture

[@liamokeeffe5215]

Great video mate 👍 your videos are really informative and down to earth

[@AllenHart999]

Liam Okeeffe Thank you Liam, 👍

[@michellecassar5785]

Thank you Allen, great for training, as always.

[@robp9553]

Hi Allen, have you had any issues with rain water in stormy weather being blown into the outer section/air intake on the flue on ideal boilers? I have an ideal vogue, with a horizontal flue. There is no white showing, it's all fitted correctly. It's just seems to be in high winds in a certain direction the rain is blown into the flue and drops to the bottom of the vogue and drips out via one of the holes at the bottom. Any ideas on what we can do to resolve, installer installed a cage over the flue which improved it but when really stormy we still get rain water in. Thanks - love the videos!

[@AllenHart999]

Hi Rob. I have heard of this but it’s normally when the flue hasn’t been installed correctly . As you know the flue needs to be level. Thanks.

[@charliesebbage9401]

Recently serviced one of these & was pretty impressed 👍🏻

[@AllenHart999]

Great to hear!

[@AllenHart999]

Merry Christmas

[@MrCarhoo]

Always informative, learning something new everytime

[@AllenHart999]

Thank you for watching.

[@chriscars3578]

Great video again Alan

[@AllenHart999]

Thank you Chris.

[@firerealINC]

Prv discharge pipe wasn't sleeved through wall. It appears

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@ThomasWorrall-nj6gr]

Hi Allen do you know what tool you need to service a Worcester 32cdi compact erp heat exchanger?

[@nayerkodsy8328]

Great video. Good for new gas engineer like my self. However on the reading the boiler ratio was 0.0017 and the max should be no more then 0.0008 can you please explain. Thanks Allan

[@thegoldennugget8000]

Always read the manufacturer's instructions dude. They are your bible.

[@bamjonny]

you've got one to many o's. 0.0080 or with a air/gas ratio control valve it's 0.0040 Alans got 0.0017 so it's far below action levels

[@davelaye7003]

@@bamjonny was about say that too. 0.008 is classed AR I believe, but 0.005 is the limit for an overhaul. Tbh I'm yet to see a reading that high

[@kalelkar]

Is there such a thing as Standard service vs Strip down service? If yes then what's the difference

[@BABYCHAOS26]

We always use a Henry when servicing

[@AllenHart999]

I wanted cordless, I also have a Henry. 👍

[@mobou6298]

, no safe isolation, can’t see any boiler components protection, can’t see any dearator for instance, on the install????

[@AllenHart999]

TB118 is our video on safe isolation. Thanks kzbin.info/www/bejne/a56sk2umaNKMorM

[@AllenHart999]

Deaerator isn't needed.

[@gowergas5034]

Nice to see a full service. I recently used a Kane 455 and found the printer was very slow. Your 456 seems much faster.

[@thegoldennugget8000]

My mates 455 started slow came back from a service alot faster. I have a 458 was fast has slowed right down, but I am brutal on the batteries...

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@peterdaly9989]

Brilliant video pal keep up the good work 👍

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@rythemgangstar]

If my water Is dirty is it normal

[@AllenHart999]

No

[@rythemgangstar]

@@AllenHart999 thank you buddy what can I do to make better or fix this issue sir

[@roboliver9980]

Great videos and handy to know if local plumbers may be bullshitting about things.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@zorg1010tube]

Outstanding video, your values and work attitude should be made compulsory across the trade. Thanks for sharing, already subscribed 👍

[@AllenHart999]

Let me know what other videos you would like. Thanks so much.

[@Razz60]

Excellent video really well explained

[@AllenHart999]

Thank you for watching Razz👍

[@williammcgrattan9583]

Another top show. Cheers Allen 👍

[@AllenHart999]

william mc grattan Thank You 🙏

[@alejandrovilla4257]

Hello, what is the name of the knife with a green handle, what do you use? I'm interested in one like this to clean the condensates. Thank you

[@AllenHart999]

Stay safe. Watch this one just in case. Thanks kzbin.info/www/bejne/fpmYnXl5bLt8arc

[@stevewhiteley3364]

just curious ,do you not check the new combustion seal for leakage with the analyser and ldf the gas seals that you disturbed and do you not use a torc wrench to re tighten combustion door to MI Tolerances ?

[@AllenHart999]

I have never met anyone who uses a torc wrench, do you know how tight they need to be?

[@lazylady81]

Nice video. Are you 100% sure they'll change all the parts for 10 years if you have it serviced? Pretty sure they'll change all parts for one year due to boiler warranty but after that any part will be changed unless its general wear and tear which absolutely ridiculous as what else can it be to cause part failure?

[@AllenHart999]

I have never had any issues. Thanks.

[@snigie]

The vogue is a great bit of kit! Always seem to get a higher co reading on them, any idea why? Have one in my own house set up with a nest very good modulation

[@AllenHart999]

I must agree, These are very very good boilers.

[@MrDenis]

Hi - is the expansion vessel procedure compulsory on an annual service?

[@AllenHart999]

yes

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@vistron888]

That trap seemed very rusty. Strange. Those primary heat exchangers are made by Giannoni. Who make them for several manufacturers. But I'm sure you already know that. Looks like a 3 coil one. Unless you've got a clean system they're prone to clogging up because you don't get full pressure around each coil. The only reason Ideal are giving such long warranties is because of the bad name they got over the Isar models which were fitted all over the place under various grant schemes.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@peterreid4567]

Quick question. Should you of done a gas test because a seal was broken on the gas inside boiler. Thanks

[@AllenHart999]

no requirement to test the gas, just needs spraying

[@Ed-fp9rx]

what are the disadvantages of press fit?

[@AllenHart999]

Hi Ed. Very good question. Cost is the main one I guess. Thanks.

[@Joe0607]

Is every service you do a full strip down and if not, how do you determine if it is or not

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@tyronesylvester8522]

Can you press straight on to a drain off? Or is there actual press drain off fittings?

[@AllenHart999]

tyrone Sylvester That’s a very good question, The speedfit drainoffs have a longer tail so you can press onto it 😂👍

[@morganjones1966]

I have just had a gas service engineer at my council property ( a ground floor flat ) to conduct a service on my gas boiler. One of the first things he did was go into my bathroom he had something in his hand I asked was he looking for a plug socket? he replied no I’m looking for a window I was in the kitchen by the kitchen window he asked could I put a probe through the kitchen window. I did and told him that is the first time a gas engineer from his company and the previous company had asked to or did that. His reply was that they should. Put a probe through a window. Then moaning about the poor access to the boiler in the cupboard. he was going to report the poor access to the boiler. He proceeded to take the cover off the boiler and as far as I know, serviced the boiler. I was not paying much attention but did not see him check gas supplies to my meter as other engineers have done. The previous gas service company, engineers, would clean the boiler with a vacuum. The present company that service the boilers does not clean with a vacuum. On previous visits from this company, they have gone into my kitchen and checked my gas cooker This time he did not. While I was stood at the sink doing the same dishes, he came behind me, and I believe he took some pictures of the appliances I have in my kitchen. He was at my property, no longer than 40 minutes as I had time to do some dishes, boil the kettle and use my toaster he sent all done and left could I have some feedback please?

[@tomstrutton4351]

What a piece of cake to service and a user interface that’s easy to understand, if the ratios need adjusting, is that done via the gas valve or board?

[@AllenHart999]

Not sure you can adjust these. Thanks..

[@mohmmadasjid7944]

Top video,very helpful.Thanks

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@illuminate06]

In terms of the building regs, would the boiler service requirements on a lpg static caravan system be similar to the boiler service within a house?

[@AllenHart999]

Yes i believe so but it would be a good idea to check with the boiler manufacturer. Thanks.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@illuminate06]

@@AllenHart999 thanks a lot for your quick reply. I am already a subscriber to your channel and have found your videos brilliant. I'm changing career to become a plumber, just completing my nvq 2 and keen to progress onto gas. Have a great day mate 👍

[@mfielding007]

hi alan,im getting one of these next month,at the moment we have a main eco 25, could you give me an idea what should i be roughly paying to have it installed in the same place, thanks

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@dannyboy0236]

Have you noticed the brown debris "coffee granules" are ferrous ? Also I have noticed haveing lower return temps seem to accelerate the build up. What's you thoughts on what it could be?

[@AllenHart999]

Dan Moreton I haven’t really noticed but not sure what it is. Thanks 🙏

[@dannyboy0236]

Explains the rusty looking trap

[@AllenHart999]

Dan Moreton no idea why though. Have you ?

[@dannyboy0236]

Allen Hart maybe the it’s the quality of stainless being used. Iv also noticed the welds on som of the bigger stainless hex are ferrous to. Condense definitely speeds the forming of the debris up tho. In some applications we have boilers that see a return temp of 60+ regular are clean as a whistle

[@AllenHart999]

Dan Moreton same happens in the Viessmann heat exchangers

[@scott1506]

is 1 bar for the expansion vessel normal for every combi boiler of this size or there abouts? i have performa 28 and needs pumped up as pressure needle goes up when heating on

[@AllenHart999]

I normally do them to 1 bar Thanks.

[@necropig]

Interesting that they use what looks like a rubber seal when I've had to change a good few vaillant/glowworm and they're graphite seals but using the same HE

[@AllenHart999]

Yes it’s a rubber seal. Thanks.👍

[@ksird]

The way the vogues introduce the gas/air mixture into the burner keeps the burner door cool when burning - think that’s why they can use rubber and they last longer.

[@Altarofwater]

Is pumping to 1bar always enough for heating circle's expansion tank?

[@AllenHart999]

I normally do them just over 1 bar. Happy new year. Thanks.

[@redredbenchreview9089]

Great video Allen 👍

[@AllenHart999]

Thank You.

[@steroy69]

Nice boiler, great informative video. When buying one or these boilers do you need to specify Nat Gas or LPG so it’s fitted with the correct injectors? Or will it be self modulating?

[@AllenHart999]

steroy69 I am not sure tbh, if I was installing an LPG one I would check with ideal., Thanks

[@mattbridge6925]

Morco make LPG combi boilers which are an ideal boiler with a morco badge on. Made in Hull.

[@rayc1503]

I've got the 458, my analyser probe looks much longer 🤔. Nice simple boiler to both service and install. ✋ Allen 💪

[@chocfinigan]

I noticed that.. stumpy probe!?

[@johnburns4017]

A problem with these narrow tube spiral coil heat exchanges is that crud can form and solidify in the bottom of the coil. I prefer the Intergas heat exchanger. Built like a tank.

[@AllenHart999]

John Burns Never has an issue with any I have installed 👍

[@johnburns4017]

@@AllenHart999 Some that were on OV systems with no filter or inhibitor refreshed, I have seen block right up with a boiler a right-off. They are less forgiving than other heat exchanges.

[@AllenHart999]

John Burns If installed correctly and on a clean system you will never have an issue. Agree with you though with bad installers 👍

[@johnburns4017]

@@AllenHart999 I still prefer the Intergas heat exchanger. 👍

[@AllenHart999]

John Burns Each to there own 👍

[@kelvinellis8312]

Brilliant video Alan thanks 👍

[@AllenHart999]

Thank you.

[@junxie1599]

Hello Allen, I have watched your video few times, is this seal like G10 seal or not? All the best.

[@AllenHart999]

No it’s a different seal on the ideal vogue. Thanks

[@junxie1599]

@@AllenHart999 thanks.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@paulgarbutt9098]

Installed a vogue, efficiency level at 15% all readings fine and flow temps correct, every see this issue before?

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@javidmohammed9498]

Good video appreciate it Allen. You’re diamond.

[@AllenHart999]

Hi Javid. Thanks.

[@none-qq9lg]

Considering the vogue c40 for a 4 bedroom detached house, 1 bath, 1 electric shower and 14 rads. Will the c40 be more than adequate?

[@AllenHart999]

Depends on a number of things really, Do you know what your cold water flow rate is at the moment? Also how far away is the gas meter. 40kw is normally way too big for most people. Thanks.

[@none-qq9lg]

@@AllenHart999 the gas meter is approx 5 metres away from the boiler, not exactly sure on water flow rate but the flow is quite fast. Only considered the c40 as it has a high flow rate

[@none-qq9lg]

Hi @Allen Hart would appreciate a response

[@AllenHart999]

@UCPlH1tRtRSE4SiY66gf2dIA I have responded above. Thanks.

[@none-qq9lg]

@@AllenHart999 i responded back to you but didn't get a further response, i said the gas meter is approx 5 metres away from the boiler, not exactly sure on water flow rate but the flow is quite fast. Only considered the c40 as it has a high flow rate

[@kevalcok3727]

Push fit gas fitting. I'm I missing something???

[@kevalcok3727]

I got it.........…………. Xpress.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@ritzevespa]

I also don't change them every year, only the gaskets, some boilers don't have a hi temp gasket,. And grease em with silicone, stops any low pressure leak.

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@whitebear5405]

You want to be changing a combustion seal everytime. Keep them as van stock

[@AllenHart999]

I will from now on. Thanks.

[@BriaCroTex]

This is not something u want it is something u must change every time u are opening heat exchanger.

[@whitebear5405]

No worries Allen top service though. Customers are getting value for money. Beats alot of service engineers giving a lap dance service. (5mins no touching)

[@rarsebumbaclaat2659]

@@whitebear5405 that's the best phrase I've ever heard in the trade, cheers mate I'll shall use it the rest of my career 👍🏾

[@vosey97]

Mark I disagree there is no need to change seal on every service as long as it is in good condition .

[@jaimedamascena1142]

New Engineer here, does the boiler needs to be firing to put in service mold or just calling for heat? Great video!

[@AllenHart999]

Yes, you need a call for heat. Thanks

[@frazerwarwick3153]

Great video thank you 👌🏼

[@AllenHart999]

Thank You

[@pauls826]

Don’t know about you Allen but I love ideals for servicing there so easy also where did you get that tool bag from I want one hahah

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@dzmalekvali1110]

47%efficiency on screen??

[@AllenHart999]

Super efficiency must have been amazing on that one. Thanks.

[@stephenwatt33]

Excellent video!

[@AllenHart999]

Thank you Stevie. 👍

[@paullyons4624]

Great video Alan. You seem to really like this boiler, did you not fit a baxi in the new house? May I ask why?

[@AllenHart999]

I really do like the Ideal Vogue, I installed a baxi in my new house as it's smaller and more compact. I also like the brass etc in the baxi, Thanks.

[@e45cream72]

Another great video, thank you for your time!

[@AllenHart999]

Thank you for your time and watching my videos. 👍

[@e45cream72]

@@AllenHart999 you're welcome, I always learn at least one thing from your videos

[@SproutyPottedPlant]

These videos are great! I was curious what was inside the boiler and how it worked. I have a Gloworm one, what is the buzzing sound it makes when you run the hot water? It sounds like a fan or maybe it’s the pump. It must be normal as British Gas service it every year!

[@AllenHart999]

Do they strip the boiler down like this ?

[@johnfithian-franks8276]

Hi Allen, It shows very good customer after-sales service, but if I had been you I would have asked for two seals so that I had a spare in case another seal failed at a later date.

[@AllenHart999]

John Fithian-Franks I will buy some from merchants for van stock. 👍

[@smithy6177]

Hi Alan Have you fitted any Atag boilers?

[@AllenHart999]

Yes

[@AllenHart999]

kzbin.info/www/bejne/r6KkiZeeqLl7oK8

[@hichamgbrm1393]

Hi ! I truly like your videos. Just to know do u work individually or with a certain company ?

[@AllenHart999]

I work for myself. Thanks.

[@hichamgbrm1393]

@@AllenHart999 Oh, that's awesome. Thank you for the reply. Really appreciate it.

[@waliza001]

How much for service lke this?

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@smellslikethinice1107]

Thank you Allen, as per, great vid.

[@AllenHart999]

Thanks.

[@smellslikethinice1107]

@@AllenHart999 No, Thank you Allen. You always give all you can. Too many KZbin engineers forget to tell you to add eggs and butter when baking a cake, but you are always honest, so Thank you !!!

[@simplemind7532]

Great video! Glad i installed one in my house 👊😎

[@AllenHart999]

I installed one in my last house, Cannot fault them. Thanks for watching.

[@IbrahimAliSapnin]

Great vid. Would be good to see servicing vids on other brands as well.

[@AllenHart999]

Which brands would you like to see? Thanks.

[@IbrahimAliSapnin]

Baxi, Worcester’s, Vaillants, common ones really or just anything you have access to. Looking forward to a mini series on servicing the different makes. Thanks

[@AllenHart999]

@@IbrahimAliSapnin I have already done a few of them but i will try and add more when possible. Thank You👍