R31 RE-BIRTH Part 13: Hot Side Problems.

[@sammadis829]

love it when you change the intro music around when stuff doesn't go right gets me every time.

[@BoostGumps]

😂😂 thankyou for noticing!

[@shaun97346]

can run bigger turbos on the low mount manifold but need a spacer . i had a gt35 on my low mount setup with a 10mm spacer worked great with external gate on the rear housing. i was using a 4 bolt dump rear housing as you mentioned . love the content mate keep it coming!

[@jeremyhall964]

I had a steel wheel rb25 sized turbo on a 30 with an internal gate and I had no control on boost pressure with the little flap. Went external and no issues at all

[@zachcurran6376]

T28 will max out too early in rev range, go xr6 turbo or 3076 ebay or 3082. Good videos I'm building mine at the moment it's good watching how your doing it. Also the skid factory VL build will show you that spacer too

[@BoostGumps]

Zach Curran yeh my old setup was 3076 i want to go smaller to avoid breaking gearboxes. If i were to go t28 i would be putting a 71mm comp wheel on, I will max my injectors out before a T28 is a problem. Ill have a look at some there vids!

[@MrD1cefiro]

Great videos bro. Where did you pick up a VLT manifold? I’m chasing one. T3 10mm spacer and you can fit a gt35 size frame on 👌🏻

[@MrD1cefiro]

You could cut one of those flanges off of your wastegate adaptor and linish it flat. Look 10or so mm would allow the comp cover to clear the manifold

[@BoostGumps]

Michael D I may end up doing this. Im just paranoid about the surfaces being flat and not leaking and blowing out gaskets!

[@MrD1cefiro]

Leprechaun Laboratory yeah fair enough. To be honest I stopped the vid and commented then I watched the rest of the vid and heard your concern about gaskets and leaking 🤦🏻‍♂️. A spacer is very common man I think it would be fine. T28 should be responsive AF anyways 🤘🏻

[@bioshock425]

red gate spring is 5psi I'm pre sure. look on the kinguwana website on eBay.. and for another spacer comment. 10mm spacer. longer bolts. weld the spacer too the manifold. done.. my thoughts, gtx 3076 internal gate.

[@kylej489]

If you’re crafty with the welder you could try to weld a spacer onto the manifold

[@BoostGumps]

Haha a bit beyond my welding skills i think

[@kylej489]

Leprechaun Laboratory beyond mine too to be honest haha

[@BoostGumps]

kylej hahaha hopefully one day ill get there. Stainless to cast at this point i think is a bit lofty for sure 😂

[@kylej489]

*cough* JB Weld *cough* 😂

[@JamesM420]

Hi, Great content! Enjoying the vids. I'm running an AVO low mount manifold, 10mm spacer, with a Hypergear Turbo(internal gate), you should look em up if you're looking for options, I've found them to be very reliable.

[@BoostGumps]

Marrock love the look of the hypergear stuff from what i have read, just a bit out of my budget atm!

[@megantuohy3616]

Just go to your local steel supply and get them to make you a spacer cost you less than $20

[@doddzy9259]

Yo!! big fan your videos are awesome!! Where did Liam’s “this is what it’s all about when you’re this age” video go! Just saw it on my phone and went to the tv to jam it on and it’s gone :( keep up the good shit! Peace from Perth!

[@BoostGumps]

Jarrod Dodds thanks mate! Haha what else is in the video? Cant put my finger on the video you’re talking about haha

[@bryancrowson395]

Sell me that rb20s actuator please haha been looking for awhile for one

[@KillTyres]

use retnik beats for your music support some other youtubers his music is fire