Bosch Washing Machine Buttons not Working Fix

[@CarlBridge58]

Thank you very much. Doing this fixed the issue I had with the temp. button which was stuck in a loop, changing the water temperature non stop.

[@askmrwashywashy]

Glad it helped

[@raygodwin68]

Fixed it, thank you. I think that the problem may be caused by pushing the washing machine firmly into place using pressure on the control panel caused the buttons to dislodge.

[@suhailasaba1051]

Good video. Where is the beeper located ? Is it located on this pcb ?

[@peroperic7053]

You are legend, thank you from Croatia!

[@peterripuli9982]

I have the same machine but different problem. The display shows all the lights but can’t choose or press anything. What is wrong with it? Is it the operating electrical board or just the program somehow needs a reprogramming?? Hope you can help.

I have that same problem. were you able to fix it?

[@peterripuli9982]

@ …i couldnt try this bcus the friend i tried to help out couldnt hold so she went bought a new machine.

[@AmritShrestha-ox8cz]

Same problem has arised for me too. Anyone fixed it or advice?

[@yourhomie2938]

Me too. All lights on

[@peterripuli9982]

u can try n find a second hand ppl chuck or u bargain just to get the operating display n change it i think it could do the trick or someone know more abt electronics what to fix then i’m all ears

[@glenyscadman5591]

Thanks I will try this, from Australia

[@Mariusz_Hello_World]

You can write what you fixed because from what I can see you just took it out and put it in

[@sveinhaustveit9773]

I have Siemens machine with similar PCB and buttons. My buttons is not not moving. I think the button principle is based on capacity of the finger outside the plastic cover.

[@koenvandamme2594]

Dear Mr. Why doesn't the siemens self cleaning condenser iq700 start? When pushing the start button, all the leds around the start button light up and fall out again when releasing the button. The machine seems to have an interruption to then kIe the program. I went in assuming that the push button had failed due to heavy use over +/- 9 years of use. Measured on the PCB and saw that push button did not always pass as well. Now I ordered a new print and rebuilt the display and push buttons on the new print. Now appears to still have the same problem. I get no error code at startup. Does anyone have any idea what else can cause machine not to start? Door contact, brushes or something else?

[@Kazztration]

Hey man what does the error E:00 means on a Ascent Bosch ?

[@askmrwashywashy]

Hi. It means no faults found usually comes up in diagnostic mode. Try to reset the washer, if it comes back might be a faulty board stuck in service mode

[@mudassar34]

Hi nice video, what a coincidence I have the exact same model but it's dead no power or lights at all, any tips

[@FashionFinds30]

What you did

[@36thMAVERICK]

Thanks for the video. Did the trick 👍

[@askmrwashywashy]

Glad it helped

[@garypitt7916]

If I take the panel off the machine it works board woks as soon as I put it back in the panel it doesn’t work

[@kevwills858]

6:28 If the alcohol doesnt fix it. .. drink it and pay a technician $200 to tell you its going to cast $300 to fix ..

[@garylee3713]

My door is not opening

[@jliscorpio]

I've had that happen. Try pressing on the door and while your pressing try to unlatch the door then

[@stephendonnelly4002]

good viideo

[@jagannathpotdar144]

Good

[@jarthebigcat]

PCB cost a fortune, I think it is better to buy a new washing machine

[@MunusamyEgambarm]

Tamil

[@ashjaason402]

absolutely USELESS if you have, what your touching and doing, half off the screen, so no one can actually see what ya doin