Building a custom Stainless Exhaust system in 3 minutes

Рет қаралды 35,862

3 жыл бұрын

Building a custom stainless steel catback using vibrant parts and a cortek muffler. All bends are made out of pie cuts, everything is tig welded.

Пікірлер: 37

@aukanmeister Жыл бұрын

I think people don't realize how much time effort and money goes into a project like this. I've tried. I know I underestimated the cost and time it took by DIY'ing it.. But with enough practice, you might end up with skills like this. To make something bespoke and beautiful. Perfect job.

@Farlig69 8 ай бұрын

Looks great, from the outside... But let's have a look at the inside seeing as no back purging was done....

@kylepoirier918 3 жыл бұрын

Nice work buddy!

@AntoineMk1 3 жыл бұрын

Thanks Kyle 😊😊

@avus1.8t48 Жыл бұрын

artist 🤙🤙

@potater6163 10 ай бұрын

thats awesome welds. can you buy pipes with angled bends or do you have to make all the bends yourself like you did?

@MidwestRider559 9 ай бұрын

You can buy pipes that are pre-bent, but not like those. Typically they'll be 45 or 90 degrees. The bends he made are actually a series of cuts from a straight piece and then welded back together to form the right angles. It's a "pie cut" because it's made of several pieces. Huge advantage of this is it keeps the inside diameter the same all the way thru, and keeps the walls equally thick all the way around. The off the shelf bends from Autozone/Napa are basically straight pipes (actually tubes) that they press in and essentially crush the inside of the curve to form the bend. That's why they have the ribs on the inner side of the bend.

@rockwasequim5924 9 ай бұрын

Nice

@theguitardevil100 2 жыл бұрын

Bro, how much amperage and gas do you use on the exhaust? The quality of your weld without purge is awesome...

@AntoineMk1 2 жыл бұрын

Thanks! I weld around 50/55amp and 25/30 cfh with a #16 furick cup

@avus1.8t48 7 ай бұрын

@AntoineMk1 what diameter rod you use?

@saephan34 Ай бұрын

Resonator with the muffler makes the more quieter? Or silents it down?

@watr3od Жыл бұрын

Exhaust can be manufactured y61

@josephshubin8465 Жыл бұрын

Where do you buy your stainless straight pieces from?

@AntoineMk1 Жыл бұрын

Check out vibrant performance

@user-cb3zz4ec6w 9 ай бұрын

Did you have to disconnect the battery before you weld on under the car?

@FinesseHamilton 4 ай бұрын

Damn I didn’t even think of that, would that affect the arc/grounding of the weld?

@amineanagaa9194 6 ай бұрын

salut priere de m'informer de la longueur des tubes prsq moi je vais le tenter moi meme sur une tdi deja 'downpiped'. jusqu'a mtn j'ai x4 500mm inox, x4 250mm inox, x1 kit EPLUS Car Exhaust Pipe Control. ca suffit? sinon, j'aurais besoin de quoi d'autre? merci infiniment, j'attend votre reponse monsieur. =)

@kamil6114 2 жыл бұрын

How large a pipe he can cut with his saw at an angle of 90°?

@AntoineMk1 2 жыл бұрын

6 inches

@danielkowalski1432 2 жыл бұрын

There is a lot of welding, i also dont have machine for bending pipes and i wonder how long it will last with good welds.

@AntoineMk1 2 жыл бұрын

Should last couple years. If properly done, a weld is stronger than base material.

@danielkowalski1432 2 жыл бұрын

@@AntoineMk1 nice. Do you put the echaust in any acid after welding? Is there any sense for doing it? Will it last even longer then? What do you think? I will probably build my own exhaust system this summer!

@AntoineMk1 2 жыл бұрын

No, just leave it as is after welding. Let it cool down and you're good to go.

@danielkowalski1432 2 жыл бұрын

@@AntoineMk1 all right then, thanks alot for advice!

@65427 Жыл бұрын

@@AntoineMk1please explain, why will it only last a couple years? Shouldn’t it basically last a lifetime under normal conditions?