Building the V-Bottom Skiff: Episode 30 - Timbers for ORCA and installing the knees

  Рет қаралды 80,016

Tips from a Shipwright

Tips from a Shipwright

Күн бұрын

Пікірлер: 106
@FenellaBeach
@FenellaBeach 2 жыл бұрын
“I cut half the (pencil) line away and leave the other half” - hand held, no fence, you don’t learn that overnight. The master shipwright at work, a joy to watch and listen to - so much skill and knowledge, and humility on show, right here. These fabulous videos will surely be enjoyed by generations to come.
@gschady
@gschady 2 жыл бұрын
I always left half the line especially when someone else marked it so they could NOT blame me if THEY marked it wrong "see? I cut it where YOU marked it" do this once and they never try again ;^)
@michaelhill7471
@michaelhill7471 2 жыл бұрын
That always tickles me when he speaks of that.
@manfredschmalbach9023
@manfredschmalbach9023 2 жыл бұрын
@@gschady I do let back half my lines to have the deciding plane streak in reserve and stop planing once the line isn't visible anymore. Should You have to leave a witness line _for the others_ You probably work with the wrong people I reckon. Adult colleagues I work with shouldn't do blame games but own up to their shortcomings. How could they learn something without admitting there is something to learn? I am nearing my sixties and in shipwright-videos am learning from Lou. Was I sure to be the one never making things difficult for myself now and then, how could I be open enough to take on other people's ways to do it and probably find those "better" than "mine"? On the other hand is that problem probably the reason why I worked alone for looong periods of my work life: People on site can get utterly annoying pretty quickly 😁.
@warrenwilson7836
@warrenwilson7836 2 жыл бұрын
Nothing much better that watching a craftsman’s hands. Thanks.
@eerikkinuutinen5808
@eerikkinuutinen5808 2 жыл бұрын
Did You know. You could actually be a narrator for audio books with Your voice. I'm wathcing Your videos just for the soothing calm voice (ofcause for boat building also, but You separate from others with the voice over).
@bill7778
@bill7778 2 жыл бұрын
Especially books about boats and sailing ships.
@gasgiant7122
@gasgiant7122 2 жыл бұрын
Greetings from UK, stumbled on your Chanel but already on E30 within a few days, thank you Lou for unbelievable videos, my firs think I'd do after winning the lottery is to commission a boat built by the unassuming master of shipwrights. You seem like a guy I could learn from, you just speak with clear easy to understand language that mere mortals like me can understand, a real joy to be with👍👍👍
@michaelhill7471
@michaelhill7471 2 жыл бұрын
“You are the guidance system”. The true measure of a master.
@Antipodean33
@Antipodean33 2 жыл бұрын
Don't you just love big, beautiful, long chunks of timber like those beauties. Wooden boats have so much soul, thats why you see wooden boat festivals world wide and no fiberglass boat festivals anywhere. Even people who are not boaties or wood work aficionados admire it all
@leonclose7823
@leonclose7823 2 жыл бұрын
In a recent video, Tim Hunkin commented that KZbin is a useful medium for the transfer of the subtle, informal tips and techniques that have traditionally been passed on by apprenticeship systems. These are things that would otherwise be "trade secrets". Louis' videos are a perfect example of this. The little details about hand control and potential minor pitfalls are the sort of things that are otherwise difficult to pick up, at least without making a lot of mistakes.
@abettermousetrap
@abettermousetrap 2 жыл бұрын
No matter how many times I watch these videos I always learn something new.
@mikeburton7077
@mikeburton7077 2 жыл бұрын
I'm not a boat person but l lo e watching an master at his craft !
@TheShorebird
@TheShorebird 2 жыл бұрын
As a Home Improvement Carpenter, I use a multi-tool all the time for a lot of different things. I love it, don't know what I'd do without it actually. Me and my co-workers are always wondering how we managed before we had it. When I saw what you were about to do, I thought that a multi-tool would be perfect for the job! This skiff is turning out to be a beautiful piece of work. Any person would be proud to own it. The lines of the bow are just so slick looking. I can't wait to see it cutting through the water!
@raytheron
@raytheron 2 жыл бұрын
You made my week, Lou! Always a joy to watch and listen to you. My idea of paradise? To be able to be your helper. But that's sadly never going to happen: I'm too far away and too poor. So I just delight in your videos.
@stevenbeach748
@stevenbeach748 2 жыл бұрын
I can’t even tell you how excited I am for Orca
@Daniel_cheems
@Daniel_cheems 2 жыл бұрын
Such a great pleasure to watch a master at work. The video was over so quickly.
@MrPotatochips4
@MrPotatochips4 2 жыл бұрын
I made a two wheeled cart from a garden cart with a 5/8th D axle and 26 x 2.5" tires, just a 18" cube with the axle about in the center. moved some heavy timbers around on uneven Vermont ground. Old sayin around here is "use it up, wear it out, make it do, or do without" I learned alot from this channel, so thanks!
@michaelhill7471
@michaelhill7471 2 жыл бұрын
When Mr. Sauzedde speaks of “timbers”, I really do shiver! When he sounds delighted about something I find I am too. I truly want to buy that skiff he’s building ( crafting) because I want to live out my days aboard it.
@danielcotnoir3363
@danielcotnoir3363 2 жыл бұрын
Thanks Lou & company. It's always pleasure watching a master at work.
@J.A.Smith2397
@J.A.Smith2397 2 жыл бұрын
Love listening to ya while working on my own wood shop
@davidhall1779
@davidhall1779 2 жыл бұрын
getting down to the fine work. i have to say its a joy to watch you work this ship into shape.
@dwel2928
@dwel2928 2 жыл бұрын
Lou, and a few others, make the rest of us better woodworkers. What a privilege to be able to look over his shoulder while he makes an fits those beautiful laminations!
@mattevans-koch9353
@mattevans-koch9353 2 жыл бұрын
Thank you Lou. This beauty is getting close. Thank you for sharing and have a great week ahead.
@ThinkinThoed
@ThinkinThoed 2 жыл бұрын
This randomly popped up in my feed, lol love KZbin Algorithms sometimes. One recommendation though, to make it easier to binge watch for us newcomers is change your Playlist to play in order, it's currently in reverse. That way we can start from episode one in the playlist and it will play in order :)
@richard-gn3es
@richard-gn3es 2 жыл бұрын
I envy your ability to binge watch this channel
@scotthutson736
@scotthutson736 2 жыл бұрын
Love watching you build these boats, Lou. Your craftsmanship is amazing.
@reTool462
@reTool462 2 жыл бұрын
Always enjoyable to watch a skilled craftsman at work. Really looking forward to the orca build. Its my favourite film.
@markturner9293
@markturner9293 2 жыл бұрын
I must have missed something!
@jenvan8799
@jenvan8799 2 жыл бұрын
@@markturner9293 A true crime tiller.
@reTool462
@reTool462 2 жыл бұрын
@@markturner9293 orca, from the film "jaws" 👍
@thomasarussellsr
@thomasarussellsr 2 жыл бұрын
@@markturner9293 typo... should have been "skilled" not "killed" craftsman. And "Orca" was the boat from the movie "Jaws". Lou is planning to recreate that boat, aka the "Orca-2".
@ronwatson4902
@ronwatson4902 2 жыл бұрын
One of a kind perfectionist. I love everthing he does and every word he says as well. Same as Fenella. Thank you Lou!!!
@chuckfinley3542
@chuckfinley3542 2 жыл бұрын
I loved seeing the Multi-tool in use. I first bought one 20+ years ago & used it regularly. The only time I ever got in trouble with it was when I accidentally unplugged it while using it. I plugged it back in & the tool scarred up the brand new hardwood floor I had just installed. The instructions never told an idiot like me to switch off the tool before plugging it back in.
@thomasarussellsr
@thomasarussellsr 2 жыл бұрын
When common sense ain't so common... 😂🤣😂🤣. If anyone has spent any time in the trades, they have re-plugged a tool left on at some point. Hopefully most were lucky enough to do no damage. I've cut a few cords with skillsaws that way. Why a skill saw has a trigger lock is beyond me, and after two times having this happen, years apart, I quit locking the triggers on any tools.
@GeorgeJirout
@GeorgeJirout 2 жыл бұрын
Thank you for sharing your knowledge and skill with us!
@michaelraabe3401
@michaelraabe3401 2 жыл бұрын
I bought a Fein Multimaster when they first came out, back in the 80's. A couple of years ago I bought the latest model with the quick change blades. I love the tool. It has saved me on many occasions. A trick that I use to start an accurate cut is to clamp a freshly cut block to where I want to cut as a guide. If I can't use a clamp like on that corner post I temporarily hot glue the guide block in place. Love your videos!
@manfredschmalbach9023
@manfredschmalbach9023 2 жыл бұрын
Guiding blocks are a good way, You still gotta tune for ingrown inconsistencies though - working with a lot of burly and "complicated" aka wonderfully live wood for dashboards and panels and such, I learned that the hard way. My first oscillating tool was a cast saw I got from an orthopedist and tooling was shopmade. What a lame thing compared to today's Fein toys! Boatbuilding always needed unconventional inventive solutions.
@stefboulas
@stefboulas 2 жыл бұрын
Excellent job Lewis! A work of art and great fit
@michaelsieben7202
@michaelsieben7202 2 жыл бұрын
Hi Lou, I would like to send you warm greetings from Cologne, Germany. I've been following your videos since the beginning and was able to learn a lot from you. thanks for that. You have also made my decision for my upcoming boat project easier and I will now go for a V-bottom skiff.
@brianmacintire3064
@brianmacintire3064 2 жыл бұрын
I can't wait to see you put this in the water!
@willierants5880
@willierants5880 2 жыл бұрын
That very last part blew my mind. The part about notching the knee. Can we see that?
@thomasarussellsr
@thomasarussellsr 2 жыл бұрын
I sure hope he shows that in his next video.
@TotalBoat
@TotalBoat 2 жыл бұрын
Amazing craftsmanship as always!!
@ichigokurosaki6813
@ichigokurosaki6813 2 жыл бұрын
This probably might ‘go against the grain’ for yourself Louis. Quality runs through everything you build. However for many of us to try and build one of your Totalboats ourselves, the cost of the lumber, well it’s just mind blowing for me. So could you please show us how to build a Totalboat that’s affordable for your average joe. Thanks for all your content so far. It’s a privilege to live in an age where we can tap into the minds and skills of masters of their trade like yourself.
@jonathanbeyer7852
@jonathanbeyer7852 2 жыл бұрын
Hey Louie! I use these tools to make finish cuts all the time and I always Brad nail a guide block on the line of the cut so it keeps the blade 90* through the cut.
@thomasarussellsr
@thomasarussellsr 2 жыл бұрын
Great tip, but these cuts weren't 90° cuts. Not much in a boat is 90°, even the corners of a lot of the boards used in many boats aren't 90°.
@dozer1642
@dozer1642 2 жыл бұрын
It’s so beautiful. Thank you Lou. 👍✌️
@tompedersen6564
@tompedersen6564 2 жыл бұрын
Always a pleasure to watch. Excellent commentary. You're truly a master bringing it to us in an understandable way. Two thumbs up and 5 stars.
@douglasthompson2740
@douglasthompson2740 2 жыл бұрын
All about a good quality blade when using a multi tool. I left mine on the shelf for a few years after trying the ones that came with it. Then I used a good blade and I have used the heck out of that tool since for several years now.
@vladabocanek3703
@vladabocanek3703 2 жыл бұрын
Nice. Very nice laminates. You've kind of hit me, when talking about glue. I am the one, who doesn't always have enought. I feel so sorry for leftovers.
@juligrlee556
@juligrlee556 2 жыл бұрын
I want to build a row boat similar to what I had as a kid. I would like to be able to row up the river in Michigan where I grew up. I want to row it and only have a motor for open water but also row it up the river. My biggest issues are to decide how long to make the boat, how wide to make the boat, the taper of the Kiel, and I want to be able to get in and out of the boat on open water so I can swim, dive, scuba etc. I want to explore rivers, swamps and not be twisted aside by the currents of the river.
@gschady
@gschady 2 жыл бұрын
I'm getting "tuned up" for your next video Louis because it's got to be tight even if nobody else sees it but me
@VencelBiro
@VencelBiro 2 жыл бұрын
Damn, this episode was nice! Could have been 10x the length!
@flightplan1000
@flightplan1000 2 жыл бұрын
Thanks, Lou.
@philipshane768
@philipshane768 2 жыл бұрын
I find that when I need to follow a line with the multi-tool it really helps to chisel the line before bringing in the power tool. Just cut it in with a couple of taps and it's easier to follow the line.
@josephhertzberg2734
@josephhertzberg2734 2 жыл бұрын
Always a true pleasure
@kittonsmitton
@kittonsmitton 2 жыл бұрын
Great tips on how to do it right the first time, thank you Lou.
@SMKreitzer1968
@SMKreitzer1968 2 жыл бұрын
Looking awesome Lou!
@acraftman2823
@acraftman2823 2 жыл бұрын
First time I used one of those fine tools and cut my pencil line right down the center with almost no dust I went and bought one the next day if you wanna get really close throw one of the sanding pads they come with on I never used mine thinking it wasn't worth the effort but they work great also.
@jimharris6545
@jimharris6545 2 жыл бұрын
Excellent work and a great explanation, thank you.
@davidbridenstine6358
@davidbridenstine6358 2 жыл бұрын
Enjoying the enthusiasm.
@gav2759
@gav2759 2 жыл бұрын
I never bought a multitool for years. I guess I never considered them a serious tool. Since getting one, it has extricated me from many a tight spot and I talk like I invented it.
@TheShorebird
@TheShorebird 2 жыл бұрын
I hear you! I often wonder how I managed without one. It works when where seems like there is no other tool that would do the job.
@apistosig4173
@apistosig4173 2 жыл бұрын
@@TheShorebird Kinda' reminds me of the daze with half-a-hacksaw blade, one end wrapped with masking tape, and heaps a' elbow grease and even more patience.
@JenkinsBoatWorks
@JenkinsBoatWorks 2 жыл бұрын
Good stuff Lou. Thanks for sharing. I seem to always learn something
@Khorsathedark
@Khorsathedark 2 жыл бұрын
Amazing as always. Also, I can't wait for Orca.
@leonportelance9613
@leonportelance9613 2 жыл бұрын
I cut 1/2 the line away. lol ... astounding!
@ZacVaper
@ZacVaper 2 жыл бұрын
A motor bracket like a Dusky Drive , is the way to go. I like a full transom.
@christopherpeterson1400
@christopherpeterson1400 2 жыл бұрын
Great fitting
@dwaynekoblitz6032
@dwaynekoblitz6032 2 жыл бұрын
That will be the ONLY boat of its kind EVER. Never been built before. And will never be built again.
@Pushyhog
@Pushyhog 2 жыл бұрын
thanks Lou!
@wadeshore
@wadeshore 2 жыл бұрын
Excellent
@apistosig4173
@apistosig4173 2 жыл бұрын
Q: couldn't you use small dowells instead of nails to align the laminates? These wouldn't have to punched out afterwards - and - I would consider would strengthen the component. Your thoughts please. Your employment of the vibrating cutter was pretty impressive 👍
@gregoryh4601
@gregoryh4601 2 жыл бұрын
Dear Sir thanks for this Video. May I ask have you thought length your Videos? Just a little short to learn More but I just one Vote. Can wait too see the Horse power added to this Sweet Boat.
@TimothyBarrymusic
@TimothyBarrymusic 2 жыл бұрын
Rock on Lou!!!😎
@damoog5985
@damoog5985 2 жыл бұрын
Legend!
@warrendemers4672
@warrendemers4672 2 жыл бұрын
I have a plywood glen-L 18' and there's some rot on the cabin top. I need some advice on repairing the rotted areas and refinishing the hull, thank you!
@JohnSmith-oy3ys
@JohnSmith-oy3ys 2 жыл бұрын
Solid white oak
@nicholasdaiello7167
@nicholasdaiello7167 2 жыл бұрын
When’s the next video?!
@twilamoore8879
@twilamoore8879 2 жыл бұрын
why not attach a piece of wood to guide the blade. Even if you just held the guide with your other hand while using the multi saw. I have never used one, but it seems to make sense to me.
@koentrommel
@koentrommel 2 жыл бұрын
Any thoughts on Framing and planking a Dory with douglas fir and than glass it?
@CrimeVid
@CrimeVid 2 жыл бұрын
why not knife the line on the corner rib and notch to the line with a chisel, then you have a shelf for your multi saw to start on ?
@captaintoyota3171
@captaintoyota3171 2 жыл бұрын
ORCA!!!
@josephkimbrell243
@josephkimbrell243 2 жыл бұрын
Main beam keelson for another large work skiff, inboard motor?
@soterialagoo5430
@soterialagoo5430 2 жыл бұрын
I love to watch your youtube boatbuilding skills...are you in California?
@jeffreyny2la
@jeffreyny2la 2 жыл бұрын
Hello, what's the smallest band saw should I have in my shop for building a small wooden boat?
@danacrook4203
@danacrook4203 2 жыл бұрын
Lou, could you tell me what brand rabbet plane you used on the v- bottom?
@michaelhill7471
@michaelhill7471 2 жыл бұрын
Can this 23 footer run with a 100 hp ob?
@leandroterciterci9824
@leandroterciterci9824 Жыл бұрын
Boa noite Será que vc vende o projeto desse barco ou doa grátis
@joe-hp4nk
@joe-hp4nk Жыл бұрын
Why is the transom curved at the top? Thanks.
@TipsfromaShipwrightvideos
@TipsfromaShipwrightvideos Жыл бұрын
It gives it a nice look!
@techrfun
@techrfun 2 жыл бұрын
What is the angle of the transom?
@RobertWiggers
@RobertWiggers 2 жыл бұрын
What's the function of these "knees"?
@thomasarussellsr
@thomasarussellsr 2 жыл бұрын
They strengthen the back corners of the boat, like corner braces in an old barn between posts and beams, to counter the pressure of the water on the outside of the transom and side hull pushing in on the structure of the boat.
@michaelwilkinson2928
@michaelwilkinson2928 2 жыл бұрын
Time for an update?
@ZacVaper
@ZacVaper 2 жыл бұрын
The nails to align the knees is a good idea but if you were to use wood dowels instead; no need to remove them and will add structure.
@johngoodell2775
@johngoodell2775 2 жыл бұрын
it would be a giant pain to align that many dowels and get a snug fit while working with epoxy on the clock. THe nail method with slightly oversized holes is forgiving
@ZacVaper
@ZacVaper 2 жыл бұрын
@@johngoodell2775 Just stop....you make no sense. Take a minute and think.
@johngoodell2775
@johngoodell2775 2 жыл бұрын
@@ZacVaper dowels provide no strength to a knee in that orientation and would be a pain to deal with using epoxy. The strength is from the epoxy lamination. There are many ways to make laminated knees - one way is to just laminate the pieces, clamp, and cut the shape later. His method is another way to do it. Nothing wrong with hit.
@johngoodell2775
@johngoodell2775 2 жыл бұрын
@@ZacVaper Well you might not want to publicize that:) good luck and best wishes
@ZacVaper
@ZacVaper 2 жыл бұрын
@@johngoodell2775 Switching from nails to wood dowels would be a struggle for you, we get it. Just sit in your armchair and watch.
@johnq.public2621
@johnq.public2621 2 жыл бұрын
😃👍👏👏👏
@bradbloxsom253
@bradbloxsom253 2 жыл бұрын
Where's Lou?
@keen9629
@keen9629 2 жыл бұрын
Cutting half the line is the only accurate wat of cutting anything.
How many people are in the changing room? #devil #lilith #funny #shorts
00:39
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 25 МЛН
Building the 23' V-Bottom Skiff - Episode 13: First layer of fiberglass
18:50
Tips from a Shipwright
Рет қаралды 336 М.
Building the V-Bottom Skiff: Episode 29 - Laminating our knees with epoxy
14:45
Tips from a Shipwright
Рет қаралды 63 М.
Building ORCA - Episode 1: Searching for our lumber
26:10
Tips from a Shipwright
Рет қаралды 134 М.
Traditional Clinker Construction  Episode 4: Setting Up Part 2
9:53
Smithy's Boatshed
Рет қаралды 68 М.
Building the 23' V-Bottom Skiff - Episode 20: Flipping over the hull
14:56
Tips from a Shipwright
Рет қаралды 221 М.
S2-E4 Haven 12 1/2 - Setting Up Molds and Strongback.
30:25
The Art of Boat Building
Рет қаралды 85 М.