Massey Ferguson 135 6 Speed Restoration # 67 Adjusting the Rear Axle Bearings

[@bosshoss69lee]

Look at this minty f-er just makin vidjos of what my stunned ass is working on, thanks buddy ❤

[@robbybachmann332]

Lance. Thanks for doing these videos. I have learned allot from you.

[@BundyBearsShed]

Thanks Robby, Im glad you get something from the videos, hopefully it helps others too.

[@darrenblattner2508]

You are a crafty feller aint ya. Keep smiling Lance

[@BundyBearsShed]

Some times.

[@albertschultz7151]

Still waiting for the Diff lock shaft/cam. The timing of this excellent tutorial is spot on. Thanks Lance.👌

[@BundyBearsShed]

Thanks Albert.

[@davidsample9130]

Another good insider trick or two, really enjoy them.

[@BundyBearsShed]

Thanks David

[@WaterhouseForde]

Great video Lance, thank you. You did a much better job of explaining all that than I did a few months back. 😊

[@BundyBearsShed]

I might have done a few more than you, lol. Each time I try and better the job I did on the previous similar one.

[@charleshart6992]

Excellent!! Looking great!

[@BundyBearsShed]

Coming along slowly.

[@geoffbugden8978]

Great Stuff

[@BundyBearsShed]

Thanks Geoff.

[@johnrobinson8941]

Lance, the Massey Ferguson 100 series was my favorite of the lot, I prefer the Multipower gearbox as you get faster road speed, from my knowledge here in Australia apart from the 135, there was a 148, 155, 165, 168, 175, 178, 185, 188, I reckon you should get the lot, if finances are ok, they would make a great show piece, cheers

[@BundyBearsShed]

G Day John, The other 135 is multipower and I should be seeing what is wrong with it shortly hopefully. They were a great series of tractor for sure.

[@BuckHunterNb]

Do you set the 2 to 8 thou spec for each side? Or just the one side like in the video? I pulled my axles out and will be putting them back in once the bearings and collars are done so I have to hold my differential lock lever down before putting the right axle back in?

[@BundyBearsShed]

just one side as the axles almost touch in the middle and that gap is what you are measuring.

[@stephenparker3285]

Hi lance great video , a quick question do you need a gasket on the outside of the shims on the half shaft and what stops the oil from leaking through the shims?

[@BundyBearsShed]

I just use some sealer at times.

[@dantunno9264]

You cut away at 18.44 and the gasket disappears. I need to know where the gasket went

[@BundyBearsShed]

Still there

[@dantunno9264]

@ where is it? Where does the paper gasket go? After the shims?

[@JACKATTACKED]

Would it be hissing because you've recorded in mono Lance? Hiss through the unused channel...

[@JACKATTACKED]

On my phone, sound seems to be out both speakers.....🤔

[@BundyBearsShed]

I was watching a thing on the new mic set up and they replaced the leads as they were the problem, they bought a different brand of lead and it tidied it up. I have got another Bose cable we will try, and a Tascam 70dr to adjust it out. In the big shed there is always wind from outside and birds etc being heard, always noise up here.

[@JACKATTACKED]

I'm sure you'll get to the bottom of it Lance 😀

[@JACKATTACKED]

The birds and background are to be expected, don't think you have to worry to much about that 👍 But it is now Bundywood Productions so......😂

[@BundyBearsShed]

lol.

[@kevinb204]

What do you measure the shims with?

[@BundyBearsShed]

digital vernier calipers is good enough.

[@halilates3473]

Can we adjust it with a caliper how can I arrange it teacher

[@BundyBearsShed]

Yes with a caliper you could get a measurement of axle movement.

[@halilates3473]

Teacher how can we not measure it with a caliper 👋❤

[@BundyBearsShed]

Yes we can