MF135 Restoration #9 Removing the Pistons and the Crankshaft

Removing Pistons and Crankshaft
On this video I fit the engine to a stand and remove the rear seal, pistons and crankshaft.

[@richardshephard5335]

you are lucky with the itchy nose mate. as soon as I get oil and crap on my fingers I need a piss. thanks for the videos cheers

[@BundyBearsShed]

Yep same here often, lucky I can start and stop the camera eh, lol.

[@Mattlynch463]

I’m from Ireland and I’m restoring an mf 35 3 cylinder diesel. I had the same problem. My timing cover was cracked in the same spot and my oil pressure was low. I ended up getting the timing cover welded and the crankshaft reground and installed with oversized bearings. I am currently sending the injector pump and injectors for servicing along with replacing the lower lift arm mounting pins that go into the trumpet housing in the meantime. Between the 135 and 35 playlists I have watched a lot of your videos to assist myself when carrying out these repairs, I am very thankful for all of your videos and they are all very helpful and interesting

[@BundyBearsShed]

Thankyou, Im glad the videos help.

[@giovannifronteddu9504]

Ciao. A quanti kg stringe le viti e bulloni del lalbero motore e delle bielle . Grazie

[@BundyBearsShed]

Mains 110 ft lb 120 ft lb Con Rods Black phosphate nuts =60 ft lb Bright nuts =45 ft lb Nyloc nuts =70 ft lb

[@workwithnature]

So the bearing is not worn but has std - sexually transmitted disease! had me laughing that one.

[@BundyBearsShed]

.

[@WaterhouseForde]

Great video Lance! This is the best bit in my opinion. Looks like this engine is not too bad, a good buy. Should be a relatively straight forward rebuild. Your explanations are really good too.

[@BundyBearsShed]

Thanks Gordon.

[@robbybachmann332]

Thanks for bringing us along for the engine rebuild. Always learn something from you....

[@BundyBearsShed]

Thanks Roby.

[@brianmulligan6239]

Great instruction video.

[@BundyBearsShed]

Thanks Brian.

[@MrNixex]

Hello Lance i got an perkins A3-152 in my traktor with the crome liners and it had the classic problem pulling down the liner into the crancase and total stop as a result i wonder if i find a block made for cast iron liners will the rest of the parts just swap over to the new block ? its from 1962 and have the vertical injectors with swirl chamber in he head thanks M

[@BundyBearsShed]

Im not sure I suppose checking the liner sizes on Sparex might give a clue.

[@ethandoss180]

Do you know if a crankshaft on a gas Massey Ferguson 135 fit in a diesel Massey Ferguson 135 tractor

[@BundyBearsShed]

No it wont.

[@hooter7003]

Over 30 years ago I did Perkins parts from a vague memory STD bearings the part number ended on Zero and 1 was .010 oversized and 2 was .020

[@BundyBearsShed]

Never knew that, most now a days have 0.010 etc.

[@darrenblattner2508]

To a welder guy like me, these are cool videos Lance. You explain how parts are made to fit together so we can understand, although you make things look too easy. Thanks.

[@BundyBearsShed]

Thanks Darren, On removing the liners I had a few too many amps and marked the block on one liner but just a small trail with no depth to it. Should have checked better but not to worry.

[@johnnygagnon4968]

find my thrust washer into the oil pan??? and part of the broken piston #3 ? how did it happen?

[@BundyBearsShed]

Crank end float way too big from wear. I cant really say from here.

[@halilates3473]

Teacher what did you say about the repair guide

[@BundyBearsShed]

One on our web site for free.

[@duncanrose3891]

Can't beat the Chinese safety boots Lance....

[@BundyBearsShed]

Very comfy until I drop a shifter, lol.