C3 Corvette EASY Window Removal Tutorial TEN Minutes or LESS!

[@byronholt4912]

If it’s Corvette content, I’m watching it. ✅

[@vettekid3326]

To me getting the glass out and replacing it is pretty easy. The hard part can be getting everything readjusted to close properly, not leak and not rattle.

[@kokoshadowstryder9020]

That and the "fun" of door re-alignment after hinge and/or hinge spring replacements.

[@alex.reijnierse]

Thanks Ben! That was really helpful. Have both of them out for a power mirror removal (preparing for paint)

[@rtkracht]

This will definitely help (someday). Thanks!

[@a.c.m.e.ink.4568]

Whaaaat? How to videos don't do well? 🤨 That's the 'ONLY' reason I watch, to learn ! Well, I watch for chopstick & Noodle too ! 🐶🐶

[@thedrivewayC3]

Thanks for the info!

[@dannottingham3786]

Thanks Ben

[@raybrown4775]

Ben I wathced this vidoe three times then followed it gain on my 81 and you made it so easy for me to take thewindow out as well as replaced the regulator

[@notapplicable430]

Nicely done, Ben.

[@vtradio]

Great job, Ben! We appreciate the video. Paul

[@stfitness-du4bq]

Yes, good video Corvette Ben.

[@miguelcamino1838]

Thank you boss super helpful the felt was the issue I had didn’t know it needed to be removed

[@irabel01]

Super helpful. Thanks

[@mikestone7692]

Nice tutorial 👍🏽

[@bobbybannerman2853]

GREAT VIDEO BEN.

[@1stfitness]

This was very helpful Corvette Ben 😉👌

[@edwardwernich9259]

Excellent video, thanks!

[@JerryBoechler]

Great video. Very helpful.

[@TomHolz-e9x]

👍 Love your work! Peace ☮️

[@johnmaguire8689]

Nice work Ben, I would have probably broken that glass.😮

[@westlyhetrick1876]

The snaps on the repro felt seals don't go in nearly as easy as the originals. The originals you can push in by hand. I had a lot of trouble getting them back in once the windows were installed., the trick was an L-shaped pry bar and a hammer.

[@alviney5138]

been there done that / excellent video / best on youtube of this topic

[@dcallan812]

So, its really straight forwards. 🤣🤣 Im sure it will be helpful for a few poor people that need to remove the glass. 👍👍

[@jeffreyjones593]

Great work as always Ben. I assume the procedure is similar for manual windows?

[@roelrivera2782]

Great video. On my 80 Vette the window has a little play moving in and out. I already replaced the felt pads and the gasket that goes around the door, but for some reason it still has a little shimmy when you don't raise the window all the way up. Do you think it might need new bushings or is there some adjustment somewhere?

[@StingrayGray]

Does this work for earlier models? 1974 maybe?

[@garymcdougle-82]

What is the proper lubricant to use for the tracks?

[@johnswatch1]

What do you do if the window had been shattered and it's full of fragments?

[@ronstjohn6780]

Great video, hope I never have to do this on my ‘75.

[@oldredchevy-hh6de]

Should have included how to pull off & replace the inside stuff - door panels, trim, pull, armrests, window winder/switch, etc. That stuff can be a pain to get off & on if you don't know how.

[@TheCorvetteBen]

Many videos already on that subject all over KZbin

[@JoeDelaney-e6d]

I need to replace the window motor on the passenger door and the window is in the down position, it will not move up and down, how do I do that? 1980 Vett Thanks

[@AT4AFT20]

awesome how about the motor arm removal

[@murvisstribling4035]

On my 76stingray the passenger side window is off the track and sliding from left to right how do I stop that and put it on the right spot so it closes correctly

[@tomsummers403]

Are you sure about the need to remove the window to access the mirror? Back in 1978 I installed bright blue metallic OEM bullet mirrors that I bought from my local Chevy dealer (my buddy worked in the parts department 😊) on my 1975. It was so long ago I don’t remember what I took off to do the installation. Don’t recall removing the glass but maybe I did.

[@TheCorvetteBen]

110% I’ve removed probably 25 sets of them

[@tomsummers403]

I don’t recall how the passenger side mirror was secured. Is there a brace inside the door skin that you drill through or is there a bracket you need to install inside the door to secure the mirror?

[@GenXVette]

How much difference is there with the earlier C3s with a manual window versus electric?

[@markusstrobl1067]

No difference I can recall (I had crank windows and then power).

[@skip872]

HEY BEN, nice video, but PLEASE remove the gull thumbnail image, I did not watch your vid for a long time because I didnt think it applied, (and all of the others videos information is goofy) again thanks!!..

[@jeffreyshepherd8488]

First!

[@poman8772]

The 68’s are the worst however