Hello, Good day. Everything goes well until I try to split the part using solidify at 16:30. I click on the extruded surface, apply solidify as shown in the video, select remove material, and an error pops up: Regeneration Failure: Feature failed to regenerate. Using Creo 10.
@CADxTraining8 ай бұрын
Increase the file accuracy and try once
@jonballen15509 ай бұрын
I can't select the full loop when performing the second boundary blend (10:18 in the video). Any thought as to why this is happening?
@CADxTraining9 ай бұрын
First you hide all the sketches. Then go for blend and select the edge of the existing surface. You can only select the edge of the existing surface if the sketch is hidden. Now hold the Ctrl key and select the pre-defined datum point.
@jonballen15509 ай бұрын
@@CADxTraining Wow that was quick! Thanks for the help, love your videos!
@DigiSculptStudio5 ай бұрын
@@CADxTraining they way you understood exactly what the problem (our mistake) was and made the solution so easy to understand is commendable!
@ianthompson626810 ай бұрын
I got all the way to the Flatten-Quilt Deformation and could not get the hex pattern to wrap around the grip :-(
@CADxTraining10 ай бұрын
If it is not happening then you try to reduce the file accuracy and check one more time.
@ianthompson626810 ай бұрын
@@CADxTraining after I select "quilts / select items" under References tab, it won't allow me to select the hex pattern.
@CADxTraining10 ай бұрын
Create your hex pattern as separate body
@mustachiog9 ай бұрын
@@ianthompson6268 same here
@pagalspark28109 ай бұрын
Please tell me standard size for arrow, dimension etc
@DigiSculptStudio5 ай бұрын
Hello Sir, is there a way to add half or partial hexes as well too the grip, so as to not leave any of the grip surface emply/bald
@CADxTraining5 ай бұрын
Yes you can do that. It is possible I have already done that. Now it is your job to figure that out.
@DigiSculptStudio5 ай бұрын
@@CADxTraining I tried to do it manually by adding all the hexes on a sketch and trimming out the extra bits but it made my pc so slow it was impossible to do. Especially since creo doesn't have a pattern feature within the sketch window. Thanks for your time!
@CADxTraining5 ай бұрын
Ok
@F4-0073 ай бұрын
Hi sir, I'm trying this tutorial. but I'm facing issue at 18:20 , Flatten quilt surface is at an angle not flat like in your video . how to solve this issue
@CADxTraining3 ай бұрын
Using the "specify placement" option, you can Orient your flat and quilt, the way you want. Just try to understand how this option works. You will get your required result.
@tambaramtechnicalhead79919 ай бұрын
how to insert reference drawing in creo you inseted refrence drawing
@CADxTraining9 ай бұрын
Not possible in Creo parametric. Done by video editor.
@tamilcliff696510 ай бұрын
Creo 5.0 not given for new body option so how to create hex in new body any alternative
@CADxTraining10 ай бұрын
You can only perform this function in Creo parametric 7 or higher than that. Not possible in the lower version.
@tamilcliff696510 ай бұрын
@@CADxTraining ok bro
@abdulhadipahore107510 ай бұрын
I faced the similar problem. I tried creating the hex as capped surface instead of solid and was able to use the flatten quilt deformation on that hex. Then I solidified it. I hope there is an easy way.