ARRMA FELONY 40MM FAN UPGRADE

[@sunnyd5944]

awesome build cant wait to buy the brackets

[@camaroboy383]

Thank you my friend..🙏.. first batch coming soon..👍

[@andrewcobb6464]

I agree can’t wait. I’m sold already!!

[@rcpd3157]

Those look great and they look like they can survive some bad crashes! Nice job.

[@camaroboy383]

Thanks Jess.. hope to test very soon.. and they will be great for the bashers with the center support..👍

[@HardcoreRC]

Great job Alden, think you may be busy with those bracket in the USA 👍👍

[@camaroboy383]

Thanks brother dave.. hope to release the first batch onto eBay soon..👍

[@johnmartin7079]

Looking forward to grabbing a set of these!

[@camaroboy383]

Hope to have the first batch listed very soon my friend..😉

[@bigmanrctoys8484]

Venting the body with holes for air flow will also help. My Kraton was thermalling off with the bigger pinion, added heat sink with dual fans plus vented the body and boom! No more overheating.

[@camaroboy383]

Fans alone sorted it..👍.. Cutting the body is never an option for me... Especially on this rig.. I'm surprised you had to cut the body on the Kraton since it's wide open.. did you try just the fan upgrade without cutting the body?

[@bigmanrctoys8484]

@@camaroboy383 i didn’t cut the body, just drilled holes nice and neat on the passenger side front window, and on the side where the motor fans are and right on top of the fans. 1/4” drill bit did the trick. I don’t remember if the fans and heat sink alone did the trick. It runs awesome now with no heat issues.

[@slickshobby]

Love the passion. Subbed🖤

[@camaroboy383]

very much appreciated..

[@never-stock-rc2968]

I've been buying and buying shitty small and large fans and finally I've got some game changer fans and they are absolutely epic!!!

[@BarstoneRC]

Great video man the installation came out really clean looking. As soon as I’m home for more than 24 hours I’m going to get mine mounted up, thanks again buddy!

[@camaroboy383]

Thanks brother... Hopefully it will stay cool enough to get through a pack cycle on that 20t pinion..🤞... Let me know how it works out for you my friend..😎

[@RoughneckRC]

Nice looking brackets, keep that girl cool bro

[@camaroboy383]

Thanks brother..👍

[@mikelester5524]

Nice job bro I need those for my infraction 6s I'm out here in California

[@camaroboy383]

Thanks, appreciate that..👍..

[@mikelester5524]

Im all so running the 20 tooth in my in fraction 6s it gets a little hot I do want to upgrade the fans have you ran the speed pinon gear yet 27 tooth??🎮🏎️😜

[@camaroboy383]

I prefer the 20t for street bashing for sure... good balance of torque and speed.. 😎 I have run the 27t, car ran about 83mph in about 400ft with a pair of cheapo zeee lipo's.. 👍 If your not speed running I'd suggest lowering the motor timing in the esc, the factory set 20+ degree's creates a lot of heat for very little real world gains.. I personally wouldn't run anymore than 15* of timing on that combo..

[@mikelester5524]

@@camaroboy383 I agree I ran the 27 yesterday and hit 92 mph

[@camaroboy383]

@@mikelester5524 killer..💪

[@GyuHobbyRC]

Good directing video is good. I look forward to the next video. Have a nice day. 👏 👍

[@camaroboy383]

Thank you my friend, appreciate you..✌️.. hope you have a good day too buddy..😎

[@camaroboy383]

Fan mounts are now available on my eBay page..👍

[@never-stock-rc2968]

So for 100 bucks ntf fans come with mounts and fans...

[@camaroboy383]

@@never-stock-rc2968 correct

[@michaelstrongarrma5878]

Thanks again

[@gurkancan2163]

Hi can you maybe give me a tip where i can get such fans 40x40 with at least 26000 rpm. Or the same ones you installed. thanks

[@camaroboy383]

@@gurkancan2163 where are you located? I got most of these fans from Amazon links ..

[@joeshow750]

nice, these are gonna go quick!

[@camaroboy383]

Thanks man.. I have the same feeling my friend.. I'm making big stack of them before I post them on eBay so everyone can that wants one can get one..👍

[@aidendavis3086]

Do you think cutting out the front grille and putting wire mesh in would be just as effective?

[@JohnPopeye]

By any chance, do you know the button head screw size for the sliding motor mount? Thank you

[@KingKrashArah-Cee]

Nice! That was a beautiful job! I'm impress but then again it's Mr. Alden Cost. I'm a subscriber. Just wanna know when u are going to get back to the raminator engine? I just got mine and 3 days later my cylinder has a gouge and piston rings all broken up...break in procedure wasn't done right. Stupid me. Got a new engine coming any day now. Wanting to know if you would do my engine. I really like what u do and I like the way you speak for learning. Can you please help me out? I would greatly appreciate it. Thank you for your time and reading this .Have a blessed one!

[@camaroboy383]

Thank you my friend.. appreciate that.. sorry to hear about your engine burning down.. that's awful to hear man.. we are still in the testing stages of all the mods.. the engine is amazingly different in a good way... But It is still not exactly what I was after and will endure a few more tweaks..😉.. I want to make sure I can provide the most amount of power out of the stock engine as possible.. We may be venturing in to larger displacement soon..

[@KingKrashArah-Cee]

@@camaroboy383so can u do my engine please, like you did yours?

[@camaroboy383]

@@KingKrashArah-Cee sorry for the delay in response buddy.. I'm working on another raminator engine option at the moment.. 71cc upgrade..😎.. so my advice would be to wait until I wrap up this new project.. in the end it would be more worth while for you to go the 71cc route..👍..

[@KingKrashArah-Cee]

@@camaroboy383 can I buy the 71cc and send it to you? I don't have the money yet to buy one but soon Mr. Cost, I will buy one. Can I send it to you? TMR/eastside rc didn't want people sending him 71ccs from rogan cause they didn't do the specs right or something but I'm sure you know what to do and also I want to know is after I show you that I am for real and send you the engine, will you let me test your craft and permote you like eastside rc permotes TMR? It would work out for the both of us? Please consider this if I'm not out the way asking you this. Thank you for your time and for responding to me. It feels like an honor!

[@jondilly1974]

Common Camaroboy we need results too! 🤣😜🤘🏻

[@camaroboy383]

8s dilly in the house!!!..I can't wait to do some testing my man.. hope it works out.. 🤞.. so sick of the esc issues on this rig..

[@jondilly1974]

@@camaroboy383 just get an MMX8S and call it a day 😜

[@camaroboy383]

@@jondilly1974 I know man, but I'm a cheap bastard..🤣🤣🤣💰

[@marvy7491]

@@jondilly1974 I just ordered the spektrum 160 8s so I will definitely need these

[@xKmotx]

Nice!

[@camaroboy383]

Thank you my friend

[@never-stock-rc2968]

So 75.00 for all three??

[@michaelstrongarrma5878]

What's the part number for fans

[@michaelstrongarrma5878]

All of it I'm trying

[@michaelstrongarrma5878]

And my ESC keeps overheating on like to run so I'm going to do like two ESC I want to try your setup

[@marvy7491]

any available yet? I want 3 please

[@camaroboy383]

Sorry for the delay in response.. they should be up on eBay this weekend my friend..👍

[@Acornejo02]

Are you still selling the brackets ??

[@camaroboy383]

I am not.. my design was stolen and now they are being manufactured in china far cheaper... Keep in mind, the material, and finish is much worse than mine were.. They can still be found on ebay, even with the pictures they stole from me.. The design is solid.. just be very careful with the threads.. The material is like butter..

[@Acornejo02]

@@camaroboy383 but could you make it still ? 🤫👀

[@camaroboy383]

@@Acornejo02 I'm sure I could fire up the machine and whip one up.. I'm swamped right now though so it would probably be a week before I get to it.. completely up to you sir..let me know and I can get the ball rolling for you if you want..👍

[@camaroboy383]

@@Acornejo02 how many would you need?

[@Acornejo02]

I got a Felony, and infraction 3s and a big rock 3s I really don't know what I need so let me figure that out first but so far I could use at least 2.

[@charleswilson9139]

Could I purchase some brackets from you

[@camaroboy383]

Yes sir.. hopefully soon my friend.. just need to get enough of them machined to post the first batch..👍

[@stuartbarham3958]

Is it possible to buy the parts you make?

[@camaroboy383]

First off, thanks for stopping in to check out my channel..👍.. And, yes sir.. Are you looking for the fan mounts?

[@stuartbarham3958]

@@camaroboy383 I also the rear part you made for the felony 🙌🏼, the 3d printed part looked awesome 🙌🏼🙌🏼, I’ve just ordered a felony, I’ve been away from the rc hobby for almost 30 years 😅😅

[@camaroboy383]

@@stuartbarham3958 welcome back to the hobby my friend.. It has changed drastically since back in the day of mechanical speed controls...😎 The parts are available for sale on my eBay page.. The tail pans are out of stock at the moment though.. should have more listed soon.. 👍 By the way, congrats on the purchase man..you will love it..😎

[@stuartbarham3958]

@@camaroboy383 thank you so much 🙌🏼🙌🏼😎 I will keep checking your eBay 😎👌🏼👌🏼

[@stuartbarham3958]

I cannot find your fan mounts on your eBay 😕. I watched your video today on mounting the 40 mm fans 🙌🏼