Cammed + P1X Procharger Camaro SS (LT1) Dyno Session

Procharged 6th Gen Camaro SS in for a Cam Swap, Tuning and other upgrades!
P1X + Cam Swap + Tune:
837whp / 719 ft.lbs
(984 HP Estimated at crankshaft w/ 15% Drivetrain Loss Factor)
Baseline P1X:
590whp / 553 ft.lbs
Strictly Performance Motorsports
[phone]
[e-mail]
www.strictlyperformance.parts

[@BLUPRINT1LE]

Ok I think this is starting to become a problem, I am starting to see all these cars y’all build on the road! I believe mines need to be next 😎

[@KFreebraaap]

I am pretty close to the same setup but where did you get intake pipe and rubber adaptor for the bigger throttle body? I would like to see some closer picks of your MM catch can as it appears your routing is really clean. what pulley size? I have the P1x with stock lower pulley and 3.65 upper, but I am all forged with upgraded fuel and am trying to get to 8xx rwhp.

[@jimmyss4120]

Whats you hp now with your set up

[@jimp9877]

It’s the Procharger race MAF pipe and a silicone coupler. I had a 3.9 on it then with a 8.25 lower. It’s got a 3.7 now and making more power. I can send you pics of my MM catch can

[@KFreebraaap]

@@jimp9877 Thank you. Yes I'd love to see some pics of how you routed you MM catch can. Nice, I just built my lower end with Callies rods and diamond pistons, and installed the Jannetty rough idle blower cam, lt4 fuel system with jms bap, trinity intake. I have the 3.625 upper pulley and 8.25 lower, LT headers with full exhaust. I am still in the process of getting it remote tuned. I am really excited to see what she'll do.. It a 17 50th anniversary edition and I still only have 3k miles on it. Now if I could get some dry days to get the tune finished.

[@jimp9877]

@@KFreebraaap nice! You running a Procharger with 3.625 pulley? I’m running a 3.7 pulley with 8.25 with +30 injectors and lingenfelter big bore fuel pump along with fore innovations in tank and am out of fuel at 900 whp on e60 blend

[@KFreebraaap]

@@jimp9877 Yikes, I might need to slow my role, and bump my upper pulley back to a 3.7 at least as my fueling might not be up to snuff. I am LT4 low side & high side pump with LT4 injectors & BAP. I am still in the 5k quick pulls of tuning so I haven't run out of fuel, but it doesn't look good comparing to what you have. I made a pull with very cold temps here in the outskirts of Seattle area and fouled my plugs, so just getting it ready to run again as soon as the streets dry up. I really appreciate your input, thank you. I am looking for 800whp.

[@JBWHITEGT]

That can't be on stock pistons and valvetrain...

[@F.O.R.DFixOrRepairDaily]

If the 5.0 can why can’t this one be

[@mylilpony71]

@@F.O.R.DFixOrRepairDaily5.0 is forged from factory these cars aren’t. They don’t like anything over 700hp.

[@F.O.R.DFixOrRepairDaily]

@@mylilpony71 yeah that make sense now you mention i always wondered why I keep hearing tt mustangs stock engine and trans pushing 1000 wheel while most other gms cant

[@biglazi8243]

@@mylilpony71they can make well over 700hp on stock internals. No more than 8lbs of boost tho.

[@lsnot9583]

I'm running 9lbs on stock internals but I have methanol injection. Still running strong.

[@joemeyers1016]

Pistons and Rod's upgraded?

[@LynxIsCreative]

i would hope

[@55vic64]

How’s that manifold I can’t find and videos on it

[@Ltx2k]

Did you have to forge the motor?

[@kingdeetv65]

Yeah rods and pistons

[@rendelecollins7800]

How can I find the full build list

[@jimp9877]

Btr stage 2 blower cam, Trinity intake, fore fuel pump, +30 injectors, P1X with stage 2 IC. It’s my car if I can help with anything else let me know

[@rendelecollins7800]

@@jimp9877 you have an insta and how much was it for you

[@jimp9877]

@@rendelecollins7800 no I don’t.

[@manueljuarez5619]

@@jimp9877 how much whp gain from w/o to with cam? I’m getting this exact cam installed plus ported heads.

[@jimp9877]

@@manueljuarez5619 I’m not sure. I did the Cam, ported heads, and forged internals. I’d say 50-60whp with cam,heads

[@neilvanderveer5180]

What model wheels are they and what are the sizes?

[@jimp9877]

Weld Lagunas. 17x10.5 rears, 18x5 fronts

[@neilvanderveer5180]

Thank you

[@Edsrt-]

Ouch. 👍👍👍👍👍

[@manueljuarez5619]

What piston and rings did you go with? I’m in the process of getting mine cammed. Waiting on parts to come in. Also have installed already D1x. If you can private message me that would be help full!

[@Alexander-od6fi]

Nice car, but it would be even nicer to provide the name of the BGM.

[@stellimari]

Afflictor by Austin Woodward / Echopraxia