Muchas gracias......!! Saludos desde jalisco Mexico.
@micflynn14 жыл бұрын
The valves cleaned up nice. Pro tip for ya, when you need clean carbon off the valves I use Oven Cleaner! Spray on foam it up and be Amazed as the Carbon washes away! 😁
@FourwheelerDoctor4 жыл бұрын
I will give it a shot on the next one.
@binggo27874 жыл бұрын
great video nice job.
@travishethington88243 жыл бұрын
Great video ! Have two motors im about to start on.
@martywhitman67732 ай бұрын
Great video but never got to hear if it ran good and if it fix all the problems. Was there any issue with the rebuild and did it run strong?
@jakelandsberg59172 жыл бұрын
2 years later, how is it doing? Also do you recall what rod bearings were used?
@nwags357 Жыл бұрын
Do you happen to have a link to the sprocket holder tool you mentioned versus using the screwdriver
@cardinalbaycustoms27022 жыл бұрын
What bearing would get tight with heat? Iv got a motor that won't start when Hot. Tight to turn clutch by hand. Why would this happen any help would be great thanks
@FourwheelerDoctor2 жыл бұрын
I could be either a rod or crank bearing. I have never had one do that but also I don't work on many can ams.
@atonyrodify9 ай бұрын
Hello!I noticed you said you reuse a head gasket. Is it normal for atv head gaskets to be reused?
@FourwheelerDoctor9 ай бұрын
Yes I usually spray the gasket with copper seal and reuse. I've only ever had a couple times at the gaskets were damaged and I didn't reuse them. Just guessing I've probably rebuilt about 500 ATVs and when I just do a overbore on the cylinder I will reuse the gaskets with copper seal and have had no issues.
@utahwanderlust700 Жыл бұрын
Did I miss it or did you check ring gaps off camera?
@FourwheelerDoctor Жыл бұрын
No I didn't check the ring gaps. These were not file to fit rings.
@johndragonman3 жыл бұрын
hey i have one of these.. 100 hours of use and the rear cylinder cam chain tensioner failed.. see that bit of metal the guide sits on just under the crank shaft at 9:44.. that snapped off on mine :( the engine i think over heated causing the tensioner to melt. the chain went slack, it threw it off the cam sprocket then wrapped around the crank. i am just trying to gauge if the engine is saveable. i really dont want to remove it from the UTV, and i really dont want to split the engine to replace the bit of metal thats snapped off. do you think it would still work OK without that bottom chain guide that is under the crank shaft chain sprocket? also sadly in the UK this engine has nowhere that sells parts for them so it all has to come from china :( what do you think?
@nou84763 жыл бұрын
in my own personal experience, take the engine out and split the case, these can am engines cant have any chunks in the oil, and youll need to replace all the parts that melted/broke unless you want to rebuild the whole engine when it spins a rod bearing or main bearing from junk in the oil
@lukekremer14134 жыл бұрын
Im currently trying to time my engine after a rebuild right now as well and i noticed that when your timing cam #1 at 1:12:32 in the video, your timing lines on the cam sprocket are not perfectly horizontal with the jug. This is the same exact issue I am seeing with my 1000r engine, and only with #1 cylinder just like yours, cylinder #2 aligns horizontally perfect. How do you know that the timing marks should be rotated slightly counterclock wise rather than rotated slightly clockwise?
@FourwheelerDoctor4 жыл бұрын
In the case with the front cam. I would normally shy toward the marks being shifted slightly forward so the when the tensioner is installed it would put pressure on the chain and and rotate the cam slightly counterclockwise.
@ignaciopina40993 жыл бұрын
Is there a way to change the through shaft without opening the case ?
@CristhianSilva-c3d Жыл бұрын
Donde puedo conseguir repuesto del Rotax 1000 en ecuador
@jaywilliams0521084 жыл бұрын
Wats the torque specs for the 8mm cover bolts?
@FourwheelerDoctor4 жыл бұрын
The manual calls for 10 newton meters or 7.5 foot pounds.
@bballracer924 жыл бұрын
"heard of that happening before" Bahaha
@FourwheelerDoctor4 жыл бұрын
Once or twice
@luisconcha9153 жыл бұрын
Hola.podria ser en castellano estaría bueno
@FourwheelerDoctor3 жыл бұрын
Lo siento, pero mi dialecto sur no se traduce muy bien al español