CAR DOES NOT START OR DOES NOT RUN RIGHT AFTER CRANKSHAFT POSITION SENSOR REPLACEMENT

[@AutoRepairGuys]

Products that we use and recommend: ► TDC Pin ( check for your model): amzn.to/3NnPiRU ► Panel Removal Set: amzn.to/3YiMADu ►Torx Set: amzn.to/2hbyWgd ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Engine Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ► Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics

[@chriscusick6890]

Finally someone who shows how this specific sensor is really installed! Good job!

[@chasedavis2358]

If the sensor goes bad it won’t ruin valves, that’s what the timing chain is for, the sensor controls spark timing and injection

[@mightyhellscream5014]

What if it starts after multiple times starting the car

[@shawnkiesel5349]

My crankshaft position sensor on my Saturn fortunately doesn't need adjusting or tuning it's just pull it out put it back in.. really informative video thank you I never would have thought some engines were like that

[@jaygottheplug8274]

Thank you I came here to prepare to do my Saturn 💪

[@bottomfeeder2060]

He's not doing a crankshaft position sensor he's doing a camshaft position sensor

[@adilmchichou5710]

TDC Pin the first time I see that thanks for the information

[@melekk0]

thanks for this tutorial , and does a camshaft sensor no need be aligned too ?

[@BelindaBeck-k3x]

Can anybody tell me what the part name or part number the purple bolt he used?

[@johndoe-w3h]

How about for the E46? I got P0335 after insane a new one on my 323ci.

[@MaliciousMatt888]

My failed crank sensor on E46 325i was causing the car to stall first turn over of the day every time from loss of fuel pressure and then it would be fine but still ran rough and eventually motor started cutting out while driving and even interfering with charging system causing alternator under-excitation codes that resulted in a dead battery.

[@jaliciaruffin806]

q

[@i6nore]

I’m having this problem with a 350z it goes idle past 3000 rpm and stutters also known as bogging how did you fix your problem? Did you replace the alternator. I seen here on ur it could be that please lmk been searching forever on forums etc..

[@bobgnops]

I have a 2007 Chevy equinox and they made this vehicle from 05 to 09 I think. I’ve change the crank sensor and had problems cause wouldn’t start ruff idle and cut off. The point I’m getting at when you change the crank sensor replace it with the exact part manufacturer that came out from the vehicle not all manufacturer wire there crank sensor the same.

[@ONANDOFFDIRTROADS]

mine is having that issue i replaced the crank shaft sensor on 2018 toyota tocoma and the dealership is saying it does not need a relearn feature but it is showing issues of other cars that are not relearned

[@katrinagilder1219]

This video is really informative but I have a couple of questions: 1. Will the 20 tooth count work for all cars? What is the part number of the TDC tool or where can I buy it from?

[@mowsisla5501]

Hi I got. Ford focus 16 2004 I changed my water pump and tminng belt tensioner never opened crankshaft bolts or belt evry was lining up piston tdc I hade secure bolt on the side rotated 2 revolutionar I. Oly mistake was neve checked crankshaft sensor positioning .. At end ca won't started. Any help mate. Thanks

[@igorfed993]

“Ok….ok…ok” lol good video overall

[@Rohan-gz6rg]

Hey guys I have a 2012 ford explorer 2.0 liter 4 cylinder EcoBoost change the harmonic balancer and didn’t align it before pulling it off so after replacing the new one the timing of the pulley is out engine up n dwn …could I try the same like what the video suggested?

[@HappyCasmiro]

Thanks for the video sir .I have big problem here with my ford fiesta tdci 1.6L 2009 model i swapped the engine with 2010 model it came with its own cam sensor and also crank sensor but the fly wheel was not the same so i put the one from my old engine and also the throtol .So after all done the car cant start at all its only cranking and it shows that there is fuel going and stark in the pressure pump not coming out to the injectors.

[@abdulazizgazzaz9578]

how did you fix it ?

[@naser5630]

i replace transmission for fiat 500 l and car not start up what is the problem please advised me

[@princeclive1913]

What model and what engine ⁉️

[@1jerrymaria]

Had to change the camshaft in my 2011 chevy tahoe and a few lifters,once we got everything back together we have no power. The battery was completely dead. After charging battery and turn switch to start, I'm getting nothing. Any ideas?

[@Synetheia]

Same here

[@phayvanhmalaythong1406]

Hi where can I buy a TDC locator bolt for 2013 evoque?

[@NjabuloDube-o7f]

What can be the cause of crankshaft to not turning

[@oliverhayesthecreator4988]

please dont tell me i have to take the engine out

[@emiliotamayo3256]

lol🤣

[@terrellscaife2411]

Yeah I have a 1999 mercury villager and it has weak ignition

[@buckhunchoyt5334]

I changed my crankshaft sensor on clk430 Mercedes and car won’t turn over help please anybody

[@JesseEdwards-d1x]

O rings on it get advise on them

[@dougsmith4525]

I replaced the crank sensor on my 2012 kia soul and it still runs rough and the tach drops out, etc. There isn't more than one postion for this sensor as I'm sure you know. What did I do wrong or what do I need to do to get it to work correctly? Thanks!

[@luisanibal1766]

same here. Still showing codes for crankshaft position sensor after replacing. My mechanic does not have an explanation for that.

[@Smith6265]

@@luisanibal1766 Sometimes you have to take it back to the main dealer to get them to clear the Codes. Your Mechanic probably doesn’t pay for the special privileges that the main dealer have .😀

[@johnnyfonk999]

Fire your mechanic

[@wesv6037]

I have the same issue it seems to be my harness connector, you can buy them on Amazon, I’m having dealer remake my harness, 2012 Toyota Camry XLE

[@wesv6037]

I have the same issue it seems to be my harness connector, you can buy them on Amazon, I’m having dealer remake my harness, 2012 Toyota Camry XLE

[@JesseEdwards-d1x]

Its the O rings on it

[@bethhoggard3]

My 2001 Honda civic LX was reading bad crankshaft sensor we replaced it. Still having issues with it starting & running really bad! We checked all the wires they are good. Do a new code reading an we get P0336. We are so lost on what to do next

[@xoxosh4826]

Did you ever figure it out??

[@alexismarroquin9137]

Did you fixed it . What was it

[@blackdynamite6055]

Did you ever fix it? Same thing for me. I'm tired of this b.s.! 😭

[@musaajadi1329]

@@alexismarroquin9137 yes

[@63Seddy]

Its likely the distributor itself or the timing belt is off a tooth causing this

[@smoke_stackz3168]

What about mazda 323f ?

[@masonpugh3637]

They know there stuff on Europe cars too

[@TheBmco99]

Well, after all the rattling on talking, you use an air gun on a sensor. No I don’t think so.

[@josephmercado1408]

I dropped the fucking screw in the crankshaft position sensor hole what do I do

[@badwabbit1973]

ford 2.5 if i use 20th tooth its fully on oposite side,, that balancer looks like it has double the teeth of my balancer!!!!!!!!!

[@ljutvijacalakovic1653]

ok guys

[@JakeysChannel]

ok guys ok

[@randalceniceros8157]

Ok listen ok ok Ok you can see ok

[@zefrum3]

what a crappy design; excellent video though!

[@damqndonev20]

ok

[@mrch6200]

🤠

[@auburnhater369]

Damn dude, do you breathe? Slow down.

[@mixmaster98]

this is how he does 200 vids PER car! No time to BREATHE

[@CodeB]

@@mixmaster98 i started taking a shot for every time he said the word "guys" and was hammered really quick

[@danarmstrong82]

How many times do you want to say “guys”. Jesus. Breathe....

[@1malikalik]

STFU Dan Armstrong. You sound petty and effeminate. Do you realize how many people he has helped; how much money he has saved low income families struck by COVID and can't afford a mechanic and often resort to watching YT DIY videos so they can fix their cars and go find work. Dan, go to Walmart and get you a Tampon coz you bleeding really bad.

[@cynthiakruse2385]

Mechanic has suggested crank shaft is what is making a deep engine knocking sound....car has 216,000miles and has had very good care. Where do I go from here?

[@rocketsmall4547]

@@cynthiakruse2385 find another mechanic..it sounds like you need nee spark plug wires. it may be misfire related

[@AngelReyes-bi5he]

How many times can you say the word guys in a video?

[@m80thebrawler1]

Wtf are you even saying?

[@partytimexxx8931]

Why cant they just make a sensor like other manufacturers do? Pull the old one off, plug the new one in? 🤬