Carry-On Trailer Corporation POOR QUALITY trailers from Tractor Supply

[@gatorwing6231]

Let me guess what happened. Most of low grade trailer manufactures hire kids fired from a fast food place. They are on the production line on day one since they are cheap labor. It looks like the tongue is a little over 2 inches wide. The tongue measure from the outside to the tongue was from the face of the tongue while the other side was with the tape hooked to the opposite side of the tongue. The kid just bumps it over a bit to a "Looks good to me" thing. Very important is to check paint where the welds meet parent metals. Mig welding is cheap and looks great to an armature welder even if if is bad. Usually it only melts the parent metal on only one side. After time it fails since it did not melt to the other side. It show's up in time on painted and especially powder coated welds. Even vibration will sometimes expose poor welds. It happened to me on a motorcycle lift and Craftsman trimmer. The jack flaws were corrected by the jack mfg with a new frame. The trimmer I re-welded myself since I have a machine shop. This stuff happens when cheap labor is used and is not easily visualized right away. Put some pressure near welds and look carefully for cracks at edges of welds. I hope this helps.😲👀👌.

[@starastronomer]

GatorWing So right you are! Carry-On has not got back to me yet. I will be doing a followup video.

[@dondale68]

On those trailers they are built with pretty thin steel. My guess is that they don't get the 240volt mig welders, but they just use the little 120volt cheapies! The 240v migs can give ya some penetration, but those little 120s strain to leave ya with bird crap on your steel!!

[@somchaiwongma3813]

We bought our Carry-on trailer from Tractor Trailer Supply as well in 2016. A few months later one of the 2 latches which hold the gate opened while driving on the freeway. The reason was that the gate had not been centered and therefore the pin which locks the gate was too short. They paid for fixing the problem because the trailer was still under warranty. Now the gate opened again on one side because of poor welding at the latch, it detached from the frame. The company’s response was „Its out of warranty, if a welding spot detached after one year, it’s not considered a manufacturers defect.“ Imagine a semi or a car falling apart at the welding spots after 8 years…. These trailers are a safety hazard, better Don’t drive behind one of those on the freeway !

[@starastronomer]

That's unbelievable! I bet if you did a video like I did and put it up for all to see 👀 they would have taken care of you. I agree 💯% with what you said that the weld was no good. Breaking in a year like that is NOT right. No matter what you pay for something the welds should be properly penetrated.

[@johnt5222]

In the process of repainting mine after 12 years. It's been used, abused, mostly sits outside. It was a great purchase and does more than 70% of all pickups, light duty or heavier. That said, I picked the best out of half a dozen and some were definitely better than others.

[@johndernberger1961]

I have had a 5x8SP since 2008 and it has been just a work horse for this weekend project warrior. Very pleased! Sorry to hear about these problems.

[@starastronomer]

This one has been fine John.

[@phatman4932]

I’ve had a 5x10 carry on for 3 years now. Been a great trailer and have used it for firewood, atvs, hay and livestock feed. I bought mine from a trailer dealership though not TSC.

[@sleto6542]

Video quality = 7. Information = 10. Thx for the video. Very informative.

[@Ro6entX]

I am looking into getting 5x8 trailer from Lowes for hauling my motorcycle but I am glad I came across this video so I went over to Lowe’s to measure and it was roughly 1(4 difference on right. So would that be okay? I likely will have center bar removed and weld wheel chock there but still throwing ideas in air right now since not have it yet. But point being, video is helpful all the same and I hope to see your following update on it.

[@starastronomer]

Rogent X If you are only 1/4" off that is nothing to worry about. Followup is coming soon, I hope.

[@dondale68]

This video sure showed me something else to look at. I ''assumed'' a company that builds trailers would have employees who could read a tape measure!!

[@starastronomer]

dondale68 Especially on critical areas. Poor QC.

[@Ro6entX]

@@starastronomer ah ok that’s cool. My plans for trailer are on hold until late this year or early next and still possiblity of the 5x8 but I am hoping for 5x9/10 for little extra wiggle room for loading bike.

[@johnymartin917]

I work for carry on, I drive a 4x4 forklift stacking trailers 6 high then loading them on semi's. I do not work in the Georgia plant , but we do receive stock from Georgia from time to time and feel there plant and quality differ from ours.

[@starastronomer]

Interesting Johny. Thanks 👍

[@kasmith9906]

I work for the ga plant and this is interesting to me. Thanks for that info...

[@chadley1986]

I have the exact same trailer. Where was the vin sticker located at. Mine has no stickers at all. And wondering if it was painted over. And do you see if they stamped the vin. Or is it just on the sticker.

[@starastronomer]

It is located on the left front side of the frame rail. It's a sticker with information on it and the Vin number is on it.

[@kevindove3778]

Yeah that's a bunch of BS I encourage you to get a hold of the manufacturer let them know about you know if they don't take care of the problem that you're going to do a follow-up video on what they said The best of luck to you thanks for sharing

[@starastronomer]

Kevin Here is the update: kzbin.info/www/bejne/iZmYapeqibuDn8U

[@paypatay1]

I bought 4x7 carry-on in 2004. The only problem I have ever had with it was the tires dry rotted after 10 years so I had to buy new ones.

[@philos212]

I am wondering if this is a common quality issue with Carry-on Trailers. I see so many of these on the lot of the local Lowes. Without fail every one of them have paint issues and most have rust.

[@starastronomer]

@philos212 Good question.

[@Megamanx305]

What is the coupler height on this trailer? Thanks!!!

[@budsworld22]

I’ve had my 4x7 for over 10 years and hauled everything from boilers to motorcycles. I’ve had no issues actually I’m turning it into a small camper for my daughter . Sorry yours is not up to par .

[@starastronomer]

Bud’s World Thanks. Could be QC has gone downhill since then to save $$$.

[@gregpomes7099]

I am on my second carry on my first one it was a 4 x 8 I wanted something bigger so I purchased a 5 x 8 to hold two motorcycles my first one I’ve used for five years and my second one I have now three years really no problem It’s possible you just got a Bad one just like anything else Could they have constructed a little bit better yeah I think so but we probably could say that about a lot of things that we purchased for the price I don’t think it’s a bad deal if you look at Lowe’s trailers. And the carry-on trailer for the price in my opinion the carry-on is so much better

[@dondale68]

I seriously doubt they used any primer. Were you allowed to look over the trailer before accepting final sale?? I'll carry a tape while looking at some OTHER trailers, I've already heard enough about those 'Carry On' trailers!

[@starastronomer]

dondale68 I looked it over when I bought it but who knew you had to check to make sure it was built square, etc. The paint looked good it wasn't until after the winter it started peeling.

[@dondale68]

@@starastronomer The paint really wouldn't bother me, not near as much as that tongue being off center as much as it is! Just a simple tape measure would've prevented that!

[@Methodical2]

I'm buying my first trailer and will be carrying my measuring tape with me. Thanks. Based on my research, it is know that these trailers are not the best quality when compared to those trailers costing 2-3x as much and is basically for us weekend warriors. So, it won't be a surprise to me if there are some unsightly things. I will be ok with some of the cheap stuff since I won't be using it day in and day out for work and will be using it mainly to haul my ZT mower to cut my parent's lawn. I don't want to spend too much money since it's not a work trailer. However, I will arm myself with a can of Rust Oleum paint and measure the coupler bar. I am looking at the newer model units. The old ones are hard to come by. Also, there are no discounts anymore.

[@starastronomer]

Methodical2 Yes, I've learned my lesson. Always measure before you buy. And I actually carry a tape measure in my car but never thought I would need to double check their work.

[@toddpeterson1673]

Sorry, to say I also bought one, now looking how to upgrade it, it has done well for 10 years but, now want to update, it has done me well so far......

[@TROUBLE8088]

Oh hell no!!!! I'm looking for a trailer right now! Not at TRACTOR Suppy that's for sure now!!!!

[@davedaugherty3781]

i have 2 trailers by carryon. i figure as long as they tow straight and dont break while towing they are fine. as far as paint? carry on has good trailers. doest take much to sand the fenders down and prime them and repaint them simple i do it every year before winter,. rock chips etc

[@starastronomer]

Well dave daugherty, if you would have been happy with the trailer I bought and the TWO ISSUES it had, God bless you! Not everyone (like you) requires a certain standard be held by manufacturers. Others (me) requires manufacturers meet standards of quality control in their products.

[@aamirghanchi9487]

So what did you hear back from the manufacturer? Sorry this happened to you.

[@starastronomer]

Here is the answer Aamir Ghanchi; PART 2 kzbin.info/www/bejne/iZmYapeqibuDn8U

[@davidplaster4576]

I would send the trailer back for a warranty exchange, verify that the tongue is close as possible to center on a replacement. Forget the D-hooks, leave them on, take it as a loss, and verify the replacement is the quality that you want.

[@starastronomer]

David Plaster I will be doing an update video.

[@davidplaster4576]

@@starastronomerI can't wait for an update. I just purchased the 7x12 utility trailer today, and I can say that I am impressed with the overall quality of it, and I did verify that the tongue is pretty much exact side to side..so wheewww!!! LOL. The only real downside of my trailer is also the paint job....does seem like a weak bond. I guess that is what gloss black spray paint is for, and looks like I will be touching up on it.....along with primer.

[@starastronomer]

David was it the same brand as mine?

[@davidplaster4576]

@@starastronomer Yes, Carry-On

[@leroyjohnson156]

First question I had was....is the tongue angled or parallel to the body of the trailer? That is, is it designed to track slightly away from the center of the road? Or is it off center just at the front? Or did they screw up the measurements twice in two locations. If so, it would 'crab' down the road. Seems odd...either way.

[@chris22824]

I went to Tractor Supply today to purchase the 6X8 Carry On. The build quality was so incredibly poor I could not purchase it. Paint was running everywhere, the welds were horrible, wires broken etc. I bought the Karavan brand instead. These Carry-On shoulh have never left the factory. Complete JUNK!

[@starastronomer]

@miertjestoer9525 Amazing isn't it?

[@douglaswotherspoon7687]

You bought the bottom of the barrel trailer that was designed for pops to take a load to the dump every once in a while, perhaps take their riding mower to the shop for repairs. The straight tongue should have given you that clue immediately.

[@starastronomer]

I have a larger trailer. This was to be used to carry small items and predominantly for my astronomical equipment to dark skies. AS CLEARLY STATED IN THE VIDEO.

[@douglaswotherspoon7687]

@@starastronomer I get that, but I would not have wasted my money on this trailer for any reason. I am glad I passed by that trailer and got a better one. To be honest the company should feel ashamed for making the thing AND putting their name on it.

[@toddpeterson1673]

And why is the tongue bolted and not welded? It is not a tilt style trailer.... No need for bolts on the tongue.....

[@starastronomer]

@toddpeterson1673 It is welded. The adapter the tongue bolts to is welded so that places the location of the tongue.

[@johnnywishbone1349]

So you’re pulling a trailer down unevenly down the road

[@fenkellmoney8034]

Wow thanks for this information because I am looking at purchasing one

[@starastronomer]

Fenkell Money If you get one look it over very carefully.

[@billypirtle1443]

Take a good look the fender is not centered to the tire and wheel.

[@starastronomer]

I must have missed that Billy.

[@billypirtle1443]

@@starastronomer yes you had the camera over top of fender showing paint flaking off about 1 two a 1 1/4 of an inch was out side the fender if the spring bottomed out would cut the tire open.

[@AdolfoCardoza777]

If it was from Nevada, I want to let you know it was a crazy Crack guy name Carlos, that carry on trailer people refuse to fired that guy

[@starastronomer]

🙃

[@allthisfitsverywell4203]

I think they sold you a dud trailer boss man because mine's 29 and 1/4 on the DOT both sides. I would be pissed if I was you though

[@cruzr9547]

It was built on a monday

[@starastronomer]

cruz R :)

[@truthhurts2149]

I believe Lowe's and maybe tractor supply gets the rejects. I know Lowe's does from experience with other items.

[@ElectronicsForFun]

Even the paint job wants nothing to do with this trailer.

[@starastronomer]

😆😎😉

[@danburch9989]

I would not consider this trailer design as road worthy for any distance over 100 mi round trip. They're just too light and built with light gauge steel to keep the price low. Show me the beef and I'll buy it.

[@starastronomer]

I agree. This is only for around a 40 mile or so radius.

[@luish777]

That's way to off centered an inch maybe but over 2 1/2 inches no way.

[@brianlaninfa9788]

It was built during the pandemic probably ran out of primer who knows quality from all that Built-in no time period for anything built is bad sadly to say

[@hm12460]

Tough Shit Charlie strikes again.

[@elcomandante9299]

So much for buying american made products.

[@TeagueCreek]

Junk!

[@rcgray1957]

It's a $600 trailer, you got what you paid for

[@starastronomer]

@rcMORONgray I don't care if I paid $50 for the trailer. If you can't reliably have the trailers tongue straight within the trailer then don't even make one. I wanted a small light trailer nothing heavy as I have a large heavy trailer. No excuse for piss poor QC; none! So no, I did not get what I paid for. Next time think before you make an AZZ out of yourself.