Challenges in the decal business

#vinyldecals #homedecalbusiness #cardecals #cuttingplotter
In this video we will talk about challenges in the decal business and we'll give you a few tips to make the process a little easier. When working on big vinyl decals, one of the challenges is to make sure your vinyl is aligned, this and many other challenges will be covered in this video. If you want to start your own decal business, this video may help you get an idea of the different challenges that you may come across. Visit our channel to learn how to make car magnets, vinyl banners, yard signs and a lot more. It is amazing what you can do with just a vinyl cutter, compared to other type of businesses, decal business requires very little investment.
Get your equipment & materials through uscutter: uscutter.com/?...
Or through Amazon:
Graphtec vinyl cutter: amzn.to/3pIrIkS
USCutter Titan 28 inch Vinyl Cutter: amzn.to/3yC1jwn
CAMEO 4 (12 INCH): amzn.to/3dPBRvA
CAMEO PRO (24 INCH):amzn.to/3POgbNO
Oracal color guide ( only for 651 & 631 vinyl ): amzn.to/3W6Q0ow
Siser color guide: amzn.to/3ZuQJ60
TRANSFER ROLLER TAPE:amzn.to/3e1yYb3
Magnum magnetics 24"x25' : amzn.to/3P6AHdJ
Blank yard signs: amzn.to/2IBiGWM
RAPID TAC: amzn.to/37ZMl5O
Oracal 651 vinyl 10 yard roll: amzn.to/3ulmXRJ
Cutting mat: amzn.to/3uidBWZ
Blue safety ruler (31 inch long) amzn.to/3slsrKy
Squeegee: amzn.to/3bmZK8Q
Small magnets to hold vinyl in position: amzn.to/3kdE6bt
Cutting knife tool: amzn.to/3sbDTYS
Adhesive remover goof off: amzn.to/3eXrNS2

[@RDIdecals]

Get your equipment & materials through uscutter: uscutter.com/?ref=StickerAficionado Or through Amazon: Graphtec vinyl cutter: amzn.to/3pIrIkS USCutter Titan 28 inch Vinyl Cutter: amzn.to/3yC1jwn CAMEO 4 (12 INCH): amzn.to/3dPBRvA CAMEO PRO (24 INCH):amzn.to/3POgbNO Oracal color guide ( only for 651 & 631 vinyl ): amzn.to/3W6Q0ow Siser color guide: amzn.to/3ZuQJ60 TRANSFER ROLLER TAPE:amzn.to/3e1yYb3 Magnum magnetics 24"x25' : amzn.to/3P6AHdJ Blank yard signs: amzn.to/2IBiGWM RAPID TAC: amzn.to/37ZMl5O Oracal 651 vinyl 10 yard roll: amzn.to/3ulmXRJ Cutting mat: amzn.to/3uidBWZ Blue safety ruler (31 inch long) amzn.to/3slsrKy Squeegee: amzn.to/3bmZK8Q Small magnets to hold vinyl in position: amzn.to/3kdE6bt Cutting knife tool: amzn.to/3sbDTYS Adhesive remover goof off: amzn.to/3eXrNS2

[@ronaldlarocque4427]

How do I get in touch with you guys to make some vynal decals for my van

[@ThierryC2373]

To remove registration marks without risking scratching the paint, you should use Plastic Razor Blades!

[@crystalgoakey7768]

Or also I found even at some of the hobby stores it's even hard to find the really then weeding pick like the one that you've got on the video a little hack for that is if you go to like if you have a 99 cent and More store or Dollar tree or even Walmart and stuff you can find those brush toothbrush packs that have like usually the toothbrush and the tongue scraper and everything they have a little two-sided pick in their to essentially pick at your teeth it works killer for a really thin weeding pick I don't like the thick ones that come in the packs of the cricut they're just too thick for me most of them are actually I like the thin ones like that and it's really easy to find them in the those packs I bought brand new toothbrushes for everyone in my family and took their picks out of it so that I can have them for my cutter

Hello I did this business for a long time and just wanted to let you know that, you can use same transfer tape for several times. Just try to remove it more carefully and roll it back inside, in this way you can safe lots of money and material. Kind regards.

[@RDIdecals]

Wow! We will give it a try next time. Thanks for the tip and for supporting our channel.

[@leviteapparel]

You have amazing talent

[@RDIdecals]

Thank you! 🙏

[@abuubaydullah1]

I would love to see how you get a round/over lips/curves on panels on vans/car etc .

[@RDIdecals]

This one project I believe has that kzbin.info/www/bejne/qXrVlJqDgZ6th9U

[@brooksh.9980]

Just wanted to say I love your videos, you're really good about sharing your tips, tricks and challenges....watching you overcome the same problems I've run into is encouraging. Thanks for sharing so much ❤

[@leviteapparel]

😂 I wish I had seen this channel when I was about to get into this type of business. My story goes got the large vinyl cutter Purchase the vinyl And got cold feet cancel the job. Been watching you for a while if I had this 4 years ago I would go far.

[@RDIdecals]

Thank you 🙏

[@brianarneson7905]

Love your videos, guys. Very informative and motivating.

[@RDIdecals]

Thanks a lot!

[@OpandDeb]

Looks great!

[@fidelaleman8579]

wat up vato good job

[@RDIdecals]

Gracias amigo 😎

[@Saad.Zouane]

Good ❤

[@glennracoma7481]

Like this. Question; why did you not place colors onto of each other (red over the blue) then install it? Thanks nice video tutorial

[@ched999uk]

I've been working my way through your videos - Thanks. One question, do you have any tips on working out the sizing the text and logos to fit the panels as it looks like you have very uniform spacing at the edges?

[@RDIdecals]

Hello! What works best for us is using the actual measurements and pictures of the actual vehicle-though sometimes is hard to get. About what area we cover, it really depends on how much information the customer wants on their decals.

[@Gwogster]

Another great video. I just had a small question. Do you ever have a customer who wants printed graphics rather than just cut vinyl? If you do, do you have to turn the customer down or do you try and re-design their graphics so it can be cut from coloured vinyl only?...

[@RDIdecals]

Hello! The first thing we do is look at their logo-design, there has been a few customers that we turned down because of type of image required, some are opened to changes in their logos. There’s someone local that makes the printed vinyl for us but it takes a few weeks and we try not to offer this type of projects.

[@Gwogster]

@@RDIdecals thanks for the reply. Appreciate it 👍🏻

[@pantera1jes]

Hi buddy, I love your videos, can you tell me what kind o f software are you using.

[@RDIdecals]

Thank you! We use CorelDRAW for about 97% of our projects. We use Silhouette Studio with our Cameo 4 which is not that often.

[@user-vc6in3ze3n]

You use a 45 degree blade instead of 60?

[@RDIdecals]

Hello! We’ve used the 45 degree for quite some time, we use our 60 for thicker materials like rhinestone material, reflective and other materials. Thanks for watching!

[@kevingotchal1992]

What design software do you use?

[@RDIdecals]

Coreldraw x6

[@nopes1776]

Hey man it isn't ghetto if it works

[@RDIdecals]

True! 😅 thanks for watching!