Changing a Timing Chain on a Chevrolet Captiva (Common Issue For the GM 2.4 Ecotec engines)

  Рет қаралды 109,057

Alex, The Car Doctor

Alex, The Car Doctor

Күн бұрын

Пікірлер: 288
@mannixenterprisesllc492
@mannixenterprisesllc492 7 ай бұрын
Great video, Alex! Really helping me on getting started changing the timing chain on my Granddaughters 2012 Cativa sport 2.4L today 123995 miles. Reason for the maintenance, had rough low idle and rattle, but smooth running with any amount of throttle/power. I bought a code reader which came back P0016 and P0017 correlation. Which means timing chain is stretched/loose. So, I changed the oil and removed the VVT solenoids and found it packed with metal shaving specs, I did clean them and reinstalled them and ran the engine again, removed them they stayed clean. Thats one step everyone should perform, clogged VVT solenoids are not good and effect the VVT sprocket/phaser. And I bet they have metal shavings in them as well. And the metal shavings are guaranteed to be coming from the timing chain and its components. So just to add to your fantastic video which I do appreciate, before you start Drain your oil. 😀 . I`ll post updates when done. P.S. Last time I did a timing chain/belt was 1998 on a dodge Omni. basically, same removing motor mounts and a lot of jacking around! Update: After taking off the valve cover, everything looked good. Top guide looked great and from what I could see looking down into the engine looked good. Kinda worried where these metal shavings are coming from. Popped the timing chain cover off and low and behold parts fell out. The black timing chain guide was broken into a couple pieces. But the real reveal was the tensioner arm guide for the water pump/balancer chain. It was just lying there with no damage except it wasn't secured with a bolt. No bolt at all for it in sight. But the metal shavings was solved. The Balance Shaft Tensioner was just injected into the flopping chain. Will be dropping the oil pan now to look for parts. More $$$ for balancer shaft chain kit, and there is no oil pan gasket for these motors, so silicone purchase too! Update:: All done! purring like a kitten! Thanks Alex! God Bless you! The lost bolt was actually stuck up somewhere in the chain out of site because it apparently fell after taking off the exhaust phaser. As I went back to take the intake phaser off, I noticed a bolt lying inside at the edge of the oil pan, it was the balance shaft tensioner guide bolt that was missing (yeah, no oil pan work.) Weirdly it was not damaged at all. You could tell the end threads were stressed though. I used the new bolt I got at the dealership instead when reinstalling. Parts I bought and installed - Cloyes Timing Chain Set 9-4201SAVVT1, Cloyes Balance Shaft Chain Kit - 9-4202SA, Fel-Pro Valve Cover Gasket Set - VS50778R, Fel-Pro Timing Cover Gasket Set - TCS46079, Dorman OE Solutions Timing Guide Bolt - 917-954. = $676.95+tax. Other cost - magnet tool, new bolt, 24mm wrench, oil-filter, spark plugs, drivebelt, fender liner push-tabs and plenty cans of parts cleaner for a grand total of around $974.00 vs the dealership`s price of $1885.00+tax. Tip`s and stuff I had trouble with. - Main thing, Keep Alex`s video at hand to reference at all times! I subscribed! I watched the whole thing twice and probably switched to spots over 100 times. - Drivebelt pully bolt, I`d like to kick the engineer who said, hey let's put an unnecessary long bolt here! Yes, it`s best to leave it there unscrewed as much as possible. - Crankshaft bolt, stubborn rusted bolt *70*9^%!. Even though I only had an 18-volt Ryobi impact gun, the trick with it was patience, keep at it and holding the pully from moving at all. - Balance shaft gears are a Bit$h to get off and put on. Hole punch in the indention did not work for me. Had to use a big threaded bolt to wedge the gears from spinning. - Before Removing timing chain, make sure the gear marks and keyway (not the chain-colored links, 😄thanks for the phone call on that one Alex! 😄) are close to the required indexing's, exhaust 10 o`clock, intake 2 o`clock and crank shaft keyway at 12 o`clock in reference to the engine block not the car. - Dorman OE Solutions Timing Guide Bolt - 917-954 was very hard to start the threads, be patient. - Always prepare for knuckle busting on stuck bolts and cushion properly! 😄 - Any missing bolts can be bought at the dealership parts counter. But they are expensive, that one little bolt was $16+. - If you have a free CarFax maintenance schedule account for your car and add these services performed, car value increases! - All done with 3 jack stands and 1 floor jack! Again, couldn't have done it without you or this video, Alex! Subscriber for life! Thanks a million! Brett
@mike6583
@mike6583 Жыл бұрын
Alex, I followed this video as a guide to do a timing chain replacement on a 2009 Malibu with the 2.4L Ecotec engine. I appreciate your attention to detail and explanations. The lower guide bolt had tore out the threads and I had to install a helical thread insert. The upper bolt was and still is missing, I assume that it fell into the oil pan. Thank you for so much for your help.
@TobiasSaibot87
@TobiasSaibot87 8 ай бұрын
I'm a bit nervous about doing this to my 16 chevy equinox but watching this video has made me feel confident to go for it as a DIYer for the 1st time in my life but i just wanna make sure i have the right tools because i fell short on tools as usual initially when i had changed the oil/filter. However i replaced the vvt solenoids, 2 camshafts and the crankshaft position sensor. Thank You for posting this video and wish me luck
@dirtydonuts5716
@dirtydonuts5716 4 ай бұрын
Hey Alex, I'm a tech myself. I appreciate the guidance. That's one I've never did,lol. I like the way you come across your videos, good job, and keep up the good work, there needs to be more like you!
@AlexTheCarDoctor
@AlexTheCarDoctor 4 ай бұрын
I appreciate that!
@RokCotton
@RokCotton 2 жыл бұрын
Spent the weekend replacing a loose timing chain on my 2012 Chevy Equinox. It went well thanks to your walkthrough! Big thanks!
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
My pleasure buddy i’m glad you was able to tackle it yourself saving tons of money.
@mtsanchez27
@mtsanchez27 Жыл бұрын
@@AlexTheCarDoctor if my timing chain broke, you think is it worth it to replace it?
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
@weareanonymous333 just turn the crank a bit until it lines up
@jeffanderson6795
@jeffanderson6795 Жыл бұрын
Alex…thank you so much for this video ! I followed it step by step to fix my daughters 2013 Captiva timing chain. Your directions, advice, and calming voice made the job go smoothly. I’m very appreciative that you shared your skills with us. Jeff from Iowa
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
I’m glad my video helped you. Thank you for watching
@KineticAuto
@KineticAuto 7 ай бұрын
Once installed you give it a tap with a extension and a hammer. Put a rag between the extension and the tensioner to prevent metal on metal contact.
@fastbusiness
@fastbusiness 7 ай бұрын
Thanks for taking the time to make this video. It shows how to do it in the real world, instead of some others who have the engine out on a stand and make it look like an easy 15 minute job. You show all the little things where something can go wrong and how to avoid some of the problems. Anyone seriously considering doing this job at home should watch and learn.
@wardwilliams8068
@wardwilliams8068 2 жыл бұрын
Thank you, Thank you. I just finish doing the timing chain in a 2016 Chevy Equinox. It when well, I took the extra time to replace things that could be changed. And it turned out great. I look forward to seeing more videos.
@dans_Learning_Curve
@dans_Learning_Curve 7 ай бұрын
Just bought a 2013 Equinox. Will be driving it from Vegas to MN. Will definitely keep an eye on the oil level. Check the amount of blow-by. Fun fact, I haven't touched this vehicle yet. Brother-in-law did the leg work. Starts, and drives well. I'm not opposed to pulling the head and pan and replacing the low tension rings. I'm sure the oil return holes behind the oil rings are probably plugged just like my '03 Forester. They were plugged SOLID! Drill a drill bit to clean them out! It has 150,000 miles on it. Will definitely check out the timing chain. No noticable engine noise at startup.
@michaelpickarts7683
@michaelpickarts7683 7 ай бұрын
I don't understand myself as much as I hate having car troubles why am I watching Alex the car doctor? I guess job shadowing alex the car doctor is far more pleasant than my life is
@AlexTheCarDoctor
@AlexTheCarDoctor 7 ай бұрын
Thank you for watching and supporting the channel 😎
@carljuliano6534
@carljuliano6534 Жыл бұрын
Thanks for the tutorial, I replaced the chain in my 184k 2010 Equinox. Spent less than $200 in parts and took my time. Had to use "the fix" for the top bolt of the one guide.
@brenthann2623
@brenthann2623 8 ай бұрын
Alex, i love this kind of video. this is great. the other vids ive seen all have an engine setting out in the floor and they do a 20 minute timing chain swap. this "in the bay" replacement is priceless. thanks for all you do.
@AlexTheCarDoctor
@AlexTheCarDoctor 8 ай бұрын
Awesome, thank you!
@sumdumguy3741
@sumdumguy3741 Ай бұрын
I’ve been searching EVERYWHERE to find the size of the guide access plug hex. Thank you sooo much for just saying the sizes of the tools you use. Always been my favorite yt mechanic
@maintenanceman1015
@maintenanceman1015 Жыл бұрын
Great video showed if doesn't go smooth how to fix it . the extra on the bent valves helpful. Got one that just quit and cranking fast on not start . Now know what to look for . Thank you.
@dalebean889
@dalebean889 Ай бұрын
Watch your video about timing chain replacement. It was very helpful. Just change my chain this weekend. Thanks for the helpful videos. Get making them you can.
@1123-e6q
@1123-e6q 11 ай бұрын
Todays car Manufacturers need to recommend timing chain replacement same as cars with timing belt every 100k do to cheesy quality part they use.
@tracyhorton1416
@tracyhorton1416 8 ай бұрын
Great video, I am having a mechanic do this job, only because I am lazy. But I appreciate you and people like you that make videos for the masses! Awesome and Kudos to you!
@rafaelc4488
@rafaelc4488 8 ай бұрын
Just curious How much did your mechanic charge you
@geoffjackson7894
@geoffjackson7894 2 ай бұрын
Extremely helpful video, I really appreciate how thorough you are!
@AlexTheCarDoctor
@AlexTheCarDoctor 2 ай бұрын
Glad it was helpful!
@andrewleahy8749
@andrewleahy8749 Жыл бұрын
Took an impact to my crank bolt. Battery powered. Ended up over tightening it and bent the spline on the crank. Thank you.
@jakefosnacht3736
@jakefosnacht3736 2 жыл бұрын
My 08 Malibu at 96k miles timing chain jumped and broke, quoted 1800, then get a call that it was leaking down like you showed in your previous video :/ $3000 to replace engine. I’m going to move on from this nightmare! Thanks so much for the knowledge!
@jeremymackey2073
@jeremymackey2073 2 жыл бұрын
Absolutely hands down a GREAT tutorial!! You take your time to explain why and what your doing and I love it. Only thing I noticed is right above the crank is a hole in the wheel well that if you don’t have a ratchet wrench you can slide a socket and extension through to get the tensioner off. Oh and a 32mm oil filter socket is great to use for the chain tensioner. I got lucky and had a set of short stubby oil filter sockets. That’s how I did it lol but I hope to see more of your videos! Again great tutorial!!
@LegendLength
@LegendLength Жыл бұрын
Quality was amazing, i've never seen such a detailed and helpful mechanical video. They are normally filmed in near darkness with loud music over them.
@johnd.3018
@johnd.3018 Жыл бұрын
Best tutorial I ever watched. Thank you for your time and I love your positive attitude/vibe. I have this exact vehicle and it currently says on the DIC to "Service stabili trak", "Service traction control", and "engine power reduced". Chevrolet says I need to R&R the timing chain and gears. Thanks to your video, I am comfortable doing this myself, but my question so far is: How did you rotate the engine to verify all timing points lined up before you tightened your idler pulley, first loosen the idler pulley but then what? Thanks again for your time!
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
Hey there I’m glad you enjoyed my video. I verified everything by looking at the camshaft dots and crank dots to make sure they line up with the colored links on the chain then I install the crank pulley bolt in the crank without the pulley and then rotate the engine over two revolutions to make sure everything is smooth. I assumed you was talking about the crank pulley not the idler pulley
@josephmojica8859
@josephmojica8859 4 ай бұрын
Thanks a lot! I Appreciate the time you took in making this video. 17 Chevy Equinox premier NYC
@frederickdominguez4829
@frederickdominguez4829 Жыл бұрын
Alex. Great video. Great content. I'm glad you showed the process with the engine in the car. Like us regular guys would do it. Thanks again. !! Fat props.
@MrChowLFG
@MrChowLFG 11 ай бұрын
Always best to set up 2 foldable picnic tables and layout all the parts and number the parts/nut/bolts during dissemble and keep them together as assign if you're a organize person. Makes things easier to have everything off the floor and away from the car. That way the reassemble process is easier.
@joshmohler15
@joshmohler15 5 күн бұрын
Ty soo much for this. Doing this myself and this vid was great! Thanks for the tips you put in on the steps
@tjw8t1
@tjw8t1 13 күн бұрын
These are surprisingly easy to work on. I'm getting ready to buy a 2016 Buick Verano that has the last generation 2.4 with 84K. I don't expect it to have issues yet, but I know I would have to do this job at some point along with the waterpump.
@djgaffey2009
@djgaffey2009 10 ай бұрын
Awesome video man, I took my car to mechanic for service and aircon regas found out timing chain needs doing on my 2.2 diesel but they don't do it now I know roughly how long it takes so I don't get scammed with 1000's in labour
@Just-Buses
@Just-Buses 6 ай бұрын
Great video, Alex. About to do exactly the same job with an Australian version of the Craptiva, as we call them. Thanks for your guidance on how to do the job, with engine in-situ.
@jorgegarcia-s8j
@jorgegarcia-s8j 7 ай бұрын
Alex your the greatest that engine looks like an equinox maybe a 2013 2.4 4 cylinder you did a good job Dallas Texas thank you sir
@Valentine98766
@Valentine98766 2 ай бұрын
You made it look shockingly easy to put that chain on and positioned wtf wtf!??? Sheeesh
@Victor-ip8qr
@Victor-ip8qr 2 ай бұрын
Thanks alex you do good job end explanation 🎉
@KevinCar-jx1jw
@KevinCar-jx1jw 2 жыл бұрын
Awesome video .you really have a way with explaining things. Just letting u know on my 17 caddy that bent push rod. Changed the rocker arm an so far so good. Thanks for taking the time to help me out.
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
That’s wonderful keep me updated
@artfordlowery490
@artfordlowery490 11 ай бұрын
Thanks Alex for sharing this wonderful information with us 🇺🇸 damage that a time chain can do to a valve cover 😀
@malikdey-nativemoor2923
@malikdey-nativemoor2923 Жыл бұрын
What an amazing video. Sat here and watched it like a movie. Excellent Work! Phenomenal Content
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
Thanks for watching and the support it means a lot. I’m glad you enjoyed my video happy new year.
@teddybrown7229
@teddybrown7229 Жыл бұрын
Thank you for the video on the Captiva i changed mine today with no problem Thank you very much.
@Jonathan-L
@Jonathan-L 3 ай бұрын
What's the life expectancy of the cam chain tensioners for this engine? Ten years ago, we got a brand new Captiva LT 2.4 Ecotec. The cam chain tensioner rattled badly on startup (new engine), but would setting quickly. We got it sorted under warranty straight away. The vehicle has now done 55 thousand miles, and whilst there's no cam chain or tensioner noise, I'm just curious as to how long the tensioner should last? Was there ever a 'bad batch' of tensioners and perhaps the replacement ones are fault-free?
@OConnorTnP1
@OConnorTnP1 Жыл бұрын
Fantastic video for this repair. Best one I have seen. Thanks for making it!
@bradleyhutchison2393
@bradleyhutchison2393 2 жыл бұрын
im doing 0ne of these and your video help so much thank you
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
My pleasure buddy thanks for watching and I’m glad my video helped
@dans_Learning_Curve
@dans_Learning_Curve 7 ай бұрын
You mentioned the brand of the timing chain kit. What was that again? Thank you!!
@AlexTheCarDoctor
@AlexTheCarDoctor 7 ай бұрын
Cloyes!
@TheAllEngineering
@TheAllEngineering 10 ай бұрын
We have gone backwards, gone are the days where a timing chain used to last the service life of the engine, now commonly not much more life that a timing belt. May as well have timing belt.
@oizukitom
@oizukitom 7 ай бұрын
Thank you for sharing your experience. I am digging your presentation style. Subbed.
@AlexTheCarDoctor
@AlexTheCarDoctor 7 ай бұрын
Welcome aboard! Thanks for the sub!
@kicpitreal
@kicpitreal 7 ай бұрын
Alex what happened if I follow the guide just like you show up and the car steel don’t have power and it feels like is been held back?
@AlexTheCarDoctor
@AlexTheCarDoctor 7 ай бұрын
You may have clogged up catalytic converter
@Nicks_Mobile.Mechanics-service
@Nicks_Mobile.Mechanics-service 3 ай бұрын
that was awesome he said let me grab my light and show you. im like yeah thats a rechargeable flashlight lol love the videos brother
@joeriver7994
@joeriver7994 Жыл бұрын
Wow I actually watched your repair from start to finish....Great Job!!!! Im thinking of buying a 2011 equinox with a stuck engine......i'm thinking its gonna need a new chain and cylinder head......or maybe a different engine.Great tutorial!!!!
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
Hey there and thanks for watching. If you mean stop by not rotating, most likely it’s going to be at the bottom end that seized up. And will require an engine replacement or complete rebuild.
@joeriver7994
@joeriver7994 Жыл бұрын
@@AlexTheCarDoctor the owner indicated that it died at about 40mph.....said it was stuck....i haven't even looked under the hood yet. He's asking 700 for the car and it looks decent.....im thinking 2,500 for a used engine.
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
@@joeriver7994 that’s a good deal,what is the mileage?yeah that’s about right those engine are expensive
@capthowdy126
@capthowdy126 Жыл бұрын
doing this right now to my sister's car. she had been driving hers back an forward to work an she had notice oil under her car where she parked it so thought it was a seal or something an when we started looking it was everywhere except for the top over the valve pan an as soon as we took all the plastic an got it out of the way we found it, it looks the same as urs an she had been driving the thing daily to work with it like this an all of the oil that was all over the motor was coming from the hole. when u would first start it up it would sling oil out an blow a cloud or mist of oil out an the plastic was just directing it all down onto the motor an it finally started accumulating enough that it started to drip an that is the only reason it was noticed so shes insanely lucky. we got it all pulled apart this evening an going to try to get it all done tomorrow or at least as much as we can, still havent gotten the replacement valve cover, it was way to bad to repair so had to get a new one an its not arrived in the mail yet so hopefully it will be here in a couple days at most. thanks for sharing this. been a huge help.
@Leonarco333
@Leonarco333 2 жыл бұрын
I agree taking bolts and screws out is the way. Captive plenum screws (I’m looking at you, MOPAR) really irritate me. Half a thread always catches when I try to pull it off and it takes three hands and some NSFW words.
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
It sounds like you are a good mechanic, how long have you been turning winches?
@Leonarco333
@Leonarco333 2 жыл бұрын
@@AlexTheCarDoctor I’ve been wrenching on my own cars for about 10 years. Working on other peoples’ cars for about 2 years. Opening the doors on my own shop up in the rusty north in about 2-3 weeks.
@Leonarco333
@Leonarco333 2 жыл бұрын
@@AlexTheCarDoctor I just realized that sounded a little irresponsible. I’m not going it alone. The shop will be a joint venture with my friend and mentor with far more experience with both wrenching and running an independent shop. All the older guys are retiring and the young guys are working at quick lubes and dealerships. There’s a hole in the market and the quality of work I’ve been seeing on cars lately really shows it so I’m trying to be the change I want to see in the world.
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
@@Leonarco333 you can do it man also start you a KZbin channel so us southern folks can learn a thing or two and conquer our fears on rust bucket’s.
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
@@Leonarco333 nobody’s ever successful by themselves someone help along the way in one form or fashion
@guillermogreyhernandez9235
@guillermogreyhernandez9235 Жыл бұрын
thank you so much Alex .. 100% step by step
@angelicaefarrisdelrio6764
@angelicaefarrisdelrio6764 4 ай бұрын
Hello I don't know how long it'll take you to see this message Hopefully you've see it sooner than later. So your video is pretty good super super important step that is very vital you missed to put in there
@troyfrazier64
@troyfrazier64 Жыл бұрын
Awesome video. Exactly what I was looking for.
@duecedaddy05
@duecedaddy05 6 ай бұрын
Might need balance shaft components as well the intake sprocket gets chewed up when the guides fail..there's also the 2 mounting bolts for the broken guide usually get damaged too.
@dans_Learning_Curve
@dans_Learning_Curve 7 ай бұрын
1967 Chevy Bel Air 283. Timing chain worn so much that it cut a hole in the timing cover. We thought it was the front seal. Still had the leak after replacing the seal!!
@USSinGen90
@USSinGen90 6 ай бұрын
I'm not judging I love what you do but you should have a little foldable table so you can set all of your parts on while you're working. Also you can use a cupcake tray for your bolts so you don't lose them and/or those magnetic bolt holder
@AlexTheCarDoctor
@AlexTheCarDoctor 6 ай бұрын
No judgement taken buddy. This video is a little old. I’ve upgraded since then lol I got utility carts and tables now lol thanks for your support!
@HectorReyes-j3n
@HectorReyes-j3n Жыл бұрын
Great video like how you walk through everything and have time to explain what is the reason your doing it like that or the tips and trick you got when you do the job ✅👍 but I did have one question where do you get the information to torque down the bolts
@DFson
@DFson Жыл бұрын
Great job Dr Alex! Thank you for sharing. Much appreciated.
@nathankotulski
@nathankotulski 5 ай бұрын
First, just want to say thank you Alex for creating this helpful informative video. Any advice for check engine light that is still on after I cleared the codes and drove over 130 miles?
@AlexTheCarDoctor
@AlexTheCarDoctor 5 ай бұрын
Hey there, my pleasure what is the check engine light code?
@nathankotulski
@nathankotulski 5 ай бұрын
@@AlexTheCarDoctor p0016, p0011, p0017 I changed both sensors and solenoids before changing the timing chain and guides
@robertmedina6875
@robertmedina6875 Жыл бұрын
That is correct. If you don’t wrench every day, you should not use power tools to cinch the bolts back down. Because if you make a mistake and step that bolt off, you’re gonna be in a lot of hurt!
@ryanbeshears931
@ryanbeshears931 2 ай бұрын
I would absolutely come unglued trying to do this with the breather box in there 😂😂😂😂
@dnguyen2226
@dnguyen2226 2 жыл бұрын
You’re the best!! Love all your video!!
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
Thanks for the love and support I really appreciate it
@Noidentity-j4d
@Noidentity-j4d 4 ай бұрын
I did exactly as youve done on the engine and the timing marks all lined up and you told me not to worry, but as i spun the crankshaft 2 times around they are no longer lined up on the timing marks or arrows. should I worry about this?
@rickl1281
@rickl1281 8 ай бұрын
Hi Alex, great work! Can you please post the link for the blue digital torque wrench?
@Marjan67
@Marjan67 11 ай бұрын
Had to like and subscribe!! Enjoy your content!
@AlexTheCarDoctor
@AlexTheCarDoctor 11 ай бұрын
Thanks so much! Welcome to the fam!
@meblake7359
@meblake7359 Жыл бұрын
Hey Alex. Nice video. Would it help to put rags in the bottom at the top of the oil pan to keep parts from dropping in?
@danielsmithingell9806
@danielsmithingell9806 8 ай бұрын
Great video thank you. I don't think you showed lineing up tje groove in tje chain tensioner to the chain guide
@robertmedina6875
@robertmedina6875 Жыл бұрын
You’re like an engine you have to warm up properly lol that’s what happens when we get old my friend lol great video! You are a very good teacher :-)😊😊
@transparention
@transparention 5 ай бұрын
when i try to open the crankshaft bolt counterclockwise, the crankshaft pulley spin together with the chain and the phaser.. did you have to lock the pulley first or something? how do you do that?
@jayjayltz
@jayjayltz 2 жыл бұрын
Awesome Awesome Awesome video please continue!!!!! Great job!!!!!!
@naveenroberts2885
@naveenroberts2885 2 жыл бұрын
Would like to see Full Video on 2007 Dodge Charger 2.7 replace Rear main seal step by step Thanks
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
Thanks for the video idea
@giannigarbati3537
@giannigarbati3537 Жыл бұрын
Hey man excellent video you are the best. I really want to know how much will be the cost to do a job like this one. Thabks in advance.
@eznix
@eznix 2 жыл бұрын
Thanks for the video. I own a 2015 Chevy Malibu with the 2.5L Ecotec 4 cylinder engine. Does the timing chain on the 2015n suffer from the same type of wear and are the plastic tensioners also prone to breaking?
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
I have not seen a 2.5 yet with the timing failure hopefully GM fixed it
@eznix
@eznix 2 жыл бұрын
@@AlexTheCarDoctor Thank you for the reply. I am happy to hear it. 🙂
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
@Jonathan A I thought so I was not sure
@eznix
@eznix 2 жыл бұрын
@Jonathan A Thank you for further confirmation and putting my fears to rest over this issue! 🙂
@kromeout
@kromeout 9 ай бұрын
Hey Alex I appreciate the step by step procedure. Quick question If the roller lifter has a slight play and does not come out of its position, and all compression is good do u think I can still do the timing chain?
@AlexTheCarDoctor
@AlexTheCarDoctor 9 ай бұрын
Slight play is normal
@kromeout
@kromeout 9 ай бұрын
@@AlexTheCarDoctor Really appreciate that, thank you! Love the content keep the positive vibez going!
@jasminemartin5925
@jasminemartin5925 Жыл бұрын
I believe my timing went out while the vehicle was sitting(dead battery) maybe while it was being cranked. If the timing jumps do I automatically need a whole engine? Nobody has actually taken the time to look at it. Just a crank and "You need a new engine"
@solidcredit3971
@solidcredit3971 Жыл бұрын
Very thourgh video, nice job!
@MrGeko469
@MrGeko469 Жыл бұрын
Thank you for the video Does the oil have to be drained before the timing cover is removed? Your video doesn’t show it. But someone else did Thanks in advance
@shadowsoftomorrow6703
@shadowsoftomorrow6703 Жыл бұрын
Should I replace my water pump after finishing timing chain?
@chrismalings4483
@chrismalings4483 2 жыл бұрын
Very similar to my alfa romeo 2.2 JTS (GM). Shame we don't have Cloyes in UK, I'm likely going to use INS or SKS. I wonder who makes the OEM chains?
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
It might be the same engine. Hopefully someone can answer your question, I’m not sure
@kenwiz1257
@kenwiz1257 Жыл бұрын
I just finished installing the tensioner and haven’t activated it yet but the chain is very tight already. It had some slack before I screwed the tensioner in. How tight is the chain supposed to be?
@Brocky065
@Brocky065 Жыл бұрын
Hi Alex could you please put the torque settings on here please thanks for a great and helpful video cheers Paul
@franklincollins7473
@franklincollins7473 2 жыл бұрын
Is there a part number or website where i can buy the parr to fix the top bolt to the black tensioner and the timing cover plug or should I just have it welded in the center of the inside of the timing cover plug?
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
Hey there It should be a link in the description let me know if you find it there
@stephenandloriyoung5716
@stephenandloriyoung5716 7 ай бұрын
"In case of need, any nearby object becomes a hammer." Would a 24 mm end wrench work to hold/turn the front cam? The top chain guide didn't seem to be destroyed, just from a passing glimpse. So I'm wondering how the chain got past it to chew on the valve cover. There's a saying, "Mechanics are born, not made." Some people enjoy this work and have a feel for it, while others don't get it at all. Your awareness that something was wrong when torquing the guide bolt puts you in the "born mechanic" group, I think. The excitement does fade some with fatigue and the passing of decades.
@dnguyen2226
@dnguyen2226 2 жыл бұрын
Alex, what if the charger 2.7 motor locked up, is there a way to unlocked it? If so can you make a video? I got a few that is locked up..trying to attempt to save it if I could!!thanks in advance!
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
I will definitely make a video it probably won’t be on a 2.7 but another motor which is the same process on just about any motor
@rogerredwanski4696
@rogerredwanski4696 10 ай бұрын
I have a Saturn Vue, 2008, and a problem. There seem to be interference with the chain removal. The only way to remove the timing chain appears to require splitting the chain, Seems to run around some sort of castings. Have you ever seen this?
@leonardlopez3538
@leonardlopez3538 2 жыл бұрын
Thanks for this video my car is having the same problem
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
No problem buddy also I’m sorry to hear the bad news
@pablojrmunoz3048
@pablojrmunoz3048 Жыл бұрын
hey great video but if this problem occurs and car stops at a stop sign and goes out how do I know there's excessive damage. TO the motor before i decide to move forward with a timing chain replacement just to find out there was damage
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
Hey there I’m going to send you a link to my other video explaining
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
kzbin.info/www/bejne/qmPMc2x6gMpmjpo
@jameswhisler5601
@jameswhisler5601 Жыл бұрын
​@@AlexTheCarDoctor yh
@BruceBeatty-n5w
@BruceBeatty-n5w 3 ай бұрын
I changed the timing chain and guides. I then took the 2014 Captiva for a test drive and after it warmed up the engine started making a popping sound. Why?
@christophershepard301
@christophershepard301 2 жыл бұрын
Mine is doing the exact same thing! Still running but im scared it's gonna blow
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
Please don’t continue to drive it these engines are very expensive UpWord of $2000
@JosephHernandez-i2v
@JosephHernandez-i2v 15 күн бұрын
Alex, do I need to drain oil before I open up engine to replace timing chain in a Chevy equinox 2016?
@AlexTheCarDoctor
@AlexTheCarDoctor 15 күн бұрын
@@JosephHernandez-i2v it’s easier if you drain the oil you make less of a mess but you don’t have to
@JosephHernandez-i2v
@JosephHernandez-i2v 14 күн бұрын
@@AlexTheCarDoctor ok, got it. Wondering if a damaged timing chain would cause a lack of compression in the cylinders? My daughters eco tec in chev equinox 2016 was diagnosed as “should be replaced”. Trying to determine if it just needs a replacement timing chain
@nitpp
@nitpp Жыл бұрын
Thank you for this amazing video, was so helpful for me, I do the job today and everything was successful 👍
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
Glad to hear it buddy! Thanks for watching 😎
@maxayala6710
@maxayala6710 4 ай бұрын
hi your honest opinion on mellig timing chain, oil pump engine parts
@JOULES_ENTERTAINMENT
@JOULES_ENTERTAINMENT Жыл бұрын
Hi bro.. I recently mixed the 2 camshafts and I don't know which is which... 1 has number D30 F1 and 1 has D30 G1... Which 1 is the exhaust and which 1 is the intake camshaft?
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
Hey there I’m assuming it’s not the same as this engine because it’s hard to mix the exhaust and intake cam.what type of vehicle are you working on and engine size
@JOULES_ENTERTAINMENT
@JOULES_ENTERTAINMENT Жыл бұрын
@@AlexTheCarDoctor chevrolet captiva 2.4 LT LE5 engine. Same engine sa this 1
@piripipipex
@piripipipex Жыл бұрын
I took the cover rocker bolts out but one of them broke. After I could take it out I couldn't find the same bolt in the market. But when I saw your video in detail I could notice that you use normal bolts (my bolts have a metal collar with a rubber). Please guide me, how can I change it for a normal bolt like you.
@csabajuhasz7584
@csabajuhasz7584 Жыл бұрын
Hi Alex! That car work with that open top cover? Its amaizing.
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
Yep but that’s nothing I have seen baseball size holes in engine blocks and still run
@daniellecarrico261
@daniellecarrico261 Жыл бұрын
How do you keep the crank pulley from trying to turn when removing and tightening the crank bolt?
@AlexTheCarDoctor
@AlexTheCarDoctor Жыл бұрын
A impact gun is your best bet
@TobiasSaibot87
@TobiasSaibot87 8 ай бұрын
I have this issue currently too
@HarleySLA
@HarleySLA 7 ай бұрын
There's a specialty tool you can get, a harmonic balancer holder. You can use it for loosening and tightening to proper spec.
@Gerónimo-m1c
@Gerónimo-m1c 8 ай бұрын
Thank you , your a blessing sir
@AlexTheCarDoctor
@AlexTheCarDoctor 8 ай бұрын
So nice of you to say that. Thank you .
@jt_hoopz6384
@jt_hoopz6384 8 ай бұрын
What would you do if cams gear timing marks aren’t in the 10 and 2 o’clock position?
@kblandgaming9422
@kblandgaming9422 Жыл бұрын
Will this timing chain be the issue for stalling and p0011 code if the vvt solenoid and camshaft sensor have been changed but code and stalling continued
@sergiozak332
@sergiozak332 2 жыл бұрын
Great video! Thanks!
@AlexTheCarDoctor
@AlexTheCarDoctor 2 жыл бұрын
Thanks for watching
@doriwilson6991
@doriwilson6991 Жыл бұрын
What if it's already jumped time? If it backfired and then lost power could the valves or pistons get damaged? I am facing this issue with my 2013 captiva
@kyngsmash2305
@kyngsmash2305 3 ай бұрын
Did u ever figure this out, in having exact problem with exact car
@jorgegarcia-s8j
@jorgegarcia-s8j 7 ай бұрын
Hey Alex good job Dallas Texas Jorge Garcia
🕊️Valera🕊️
00:34
DO$HIK
Рет қаралды 16 МЛН
Это было очень близко...
00:10
Аришнев
Рет қаралды 6 МЛН
GM 2.0L/2.2L/2.4L Timing and Balance Shaft replacement, Kits 76209V and 76093
15:42
SA GEAR TIMING COMPONENTS
Рет қаралды 78 М.
They Need To Make Jeep This Great AGAIN!
27:00
Alex, The Car Doctor
Рет қаралды 354
14 Equinox 2.4l timing chain replacement part 1
37:08
Backwoods Restoration
Рет қаралды 37 М.
Full Build: '69 Road Runner Transformed Into Road Burner
2:58:38
POWERNATION
Рет қаралды 6 МЛН
Advanced Crankshaft Position Sensor Testing P0335
2:18:54
GoTech
Рет қаралды 296 М.
The 2.4L EcoTec | 4 Common Problems & Reliability
9:48
8020 Media
Рет қаралды 23 М.
Случай на светофоре
0:46
ЮРИЧ
Рет қаралды 699 М.
McLaren #caredit #mclaren #viralshorts #shorts
0:20
Leandro Alexandre SUPERCAR
Рет қаралды 8 МЛН
Моя тачка
1:00
Тони
Рет қаралды 1,5 МЛН